Question about 1994 GMC Jimmy

1 Answer

My 1998 jimmy wont go in to four high low works fine

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 63 Answers

I am assuming that you have the shift on the go in your truck. with the motor running, put the truck in neutral, and try shifting between the ranges. If you have a manual shift, make sure the bolts that hold the shift arm from the shifter and on the transfer case have not loosened up. You can pull the boot off the top of the shifter and see if the slot is lined up, if not check your bolts under the truck

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Why wont my 2001 jimmy go into low 4x4 and wont come out


I had a similar issue. In my case, the cause was a faulty electronic 4x4 switch, that is, the small unit with the push-buttons in the dashboard you push to engage or disengage the four-wheel drive. Replacing the switch fixed the issue.

It could probably be many different things, so I can't say for sure that this will solve your specific issue. It's probably worth checking out, though.

Jul 11, 2014 | 2001 GMC Jimmy

1 Answer

Driver side headlights not working right


Check the earth connection, sounds like it has lost the earth on the off side and both elements of the bulb are coming on together and halving the power ( causing bad elluimination)

Dec 27, 2013 | 1998 GMC Jimmy

2 Answers

Where is the headlight relay in the 1998 jimmy? Low beams won't come onat night everything else does. high beams work


There is a headlight relay in the engine compartment fuse box, but its after the headlight switch and before the dimmer switch, so it powers both high and low beam circuits.
I would check the dimmer switch.

Dec 12, 2012 | 1998 GMC Jimmy

2 Answers

4x4 not shifting into high


hi how are you doing? just had same problem with by gmc i replaced the transfurcase motor and it works fine. the electric motor moves the shifter in your transfurcase from 4hi to 4lo and 2hi.there is only 3 things that operate your 4x4 the switch the motor and the control modgual.

Jan 28, 2009 | 1994 GMC Jimmy

1 Answer

4WD UNIT JUMPS OUT OF HIGH?


EASY FIX!

Your Schro's are going bad in the 4WD HIGH Trans Case. This sucks i know. But i had the same problem berfore.

Unit will continue to work good in low range since the stress is less then on the HIGH range. I would never use the 4WD HIGH anyway...doesnt do much on the street...just tears up the gearing and schros.

Hope this helps,

THanks,

Mark

Dec 30, 2008 | 1999 GMC Jimmy

2 Answers

4wd high range does not lite or engage


I had the same problem with my 98 sierra 4x4. Turned out that the electrical activator on the transfer case was not working. It will still go into 4 low but not 4 high. Replace the electrical switch on the transfer case and it should work again.

Dec 29, 2008 | 1998 GMC Jimmy

1 Answer

4 wd low range will sometimes engage 4wd high will never engage


I had a very similar problem with my 98 gmc 2500. The 4 low would engage - though the upshifts were erratic, but no 4 high though the light sometimes came on. I changed out the electric shift solenoid or whatever it is called, on the transfer case and it worked fine after that. A fairly simple fix that can be done in 15 minutes. Hope this helps.

Dec 08, 2008 | 1998 GMC Jimmy

1 Answer

All of the running lights work except the headlights 1998 jimmy


just try this. I had the same problem here a while back. try clicking on the high beam lever. mine went bad and was stuck in between high and low beam and would not come unstuck. and it caused the headlights not to work...

Nov 28, 2008 | 1998 GMC Jimmy

1 Answer

4 wheel low works but 4 wheel high does not.


sounds like the encoder on the side of the trans on the drivers side

Nov 24, 2008 | 1999 GMC Jimmy

Not finding what you are looking for?
1994 GMC Jimmy Logo

Related Topics:

113 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...