Question about Mazda B2200

1 Answer

How to change ignition lock clyn - B2200 Mazda Cars & Trucks

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Expert
  • 56 Answers

You have to pull the steering wheel off and you can pull the lock frpm there.

Posted on Feb 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2004 Alero Oldsmobile if I buy the chipped ignition does it reprogram itself for the anti-theft device


Chipped ignition ? Key's on your car do not have transponder chip . Replacing Keys
The ignition lock cylinder and keys do not contain any coded electronic components. The lock cylinder housing contains the coded electronic components. Changing an ignition lock cylinder or replacing a key is a purely mechanical process which does not affect the vehicle theft deterrent system. To replace an existing key, simply cut a new key to match the existing one. If no keys are available, the lock cylinder must be changed. To change the lock cylinder, simply replace the existing lock cylinder with one of the same type.

Jan 13, 2017 | 2004 Oldsmobile Alero

1 Answer

1988 s15 2.8 6 clyn stalling out


I would start with the air and fuel filters. Next would be fuel pressure and spark plug wires. Then I would check the ma's air flow sensor. Not enough informationinformation, with a limited problem I can only give a limited attempt for solution.

Apr 08, 2014 | 1993 Chevrolet S-10 Blazer

1 Answer

Wont shift into first or second


you may need a new clutch and pressure plate or slave clyn

Mar 02, 2014 | Saab 900 Cars & Trucks

1 Answer

Ford truck


im sure you also have a check engine light flashing.its a misfire in one or mor cylinders,the cause is very common the coil on top of spark plug goes bad. but you have to find out which coil.if its running rough at idle strat with #1 cyl and pull injector connector,if there is a change in idle speed then this is the or one of the bad cylinders.if idle drops then coil is good.then just reolace bad coils.

Jul 18, 2013 | Ford F-250 Cars & Trucks

1 Answer

How do i know whether to change the ignition switch or the ignition lock ( cylinder& keys) to my 2001 ford f-150


Well if the lock is turning the switch, the lock is doing its job.
Sometimes the link between the lock and the switch wears out, but thats rare.

Jul 28, 2012 | Ford F-150 Cars & Trucks

2 Answers

If i change my ignition after a break in do i need a new key for the doors and ignition too


If the door lock is undamaged then it's fine to use the old key in the door and the new key with the ignition - you then have 2 separate keys for ignition and door -
I dont quite understand the question... could you word it fidderently,
You said you "changed my ignition" - which parts of the ignition?

Jan 22, 2010 | 2000 Nissan Xterra

2 Answers

How too change the ignition switch on a 88


disconnect negative battery cable.place the ignition lock in the off lock position. remove the 2 switch mounting screws.disconnect the switch from the rod.disconnect the wiring and remove the switch.TO INSTALL.ignition switch installation for non tilt columns.move the the ignition switch slider to the off unlocked position move the slider all the way down.then back 2 clicks.the remote rod hole in the ignition switch slider should now be centered.insert the remote rod in the ignition switch slider hole and install the ignition switch on the steering column.tighten the attaching screws to 35 inch lbs.ignition switch installation for tilt columns.insert the ignition key in the lock cylinder and turn the cylinder to the off unlock position.move the ignition switch downward to eliminate any slack and tighten the attaching screws to 35 inch lbs.

Nov 26, 2009 | 1988 Jeep Cherokee

1 Answer

I need to change my ignition lock cylinder but i cant turn the ignition switch lock cylinder to the ON position. What do i do?


well is it that the key wont turn or dont have key? you can drill out the lock use a big bit it will distroy the tumblers so you can use a screw driver turn it and pull out

Jun 04, 2009 | 1998 Pontiac Grand Prix

1 Answer

The battery in my 2006 pontiac vibe went dead. I recharged it; however, the setting for the door locks changed. It now unlocks automatically when I turn the car off instead of when I put the car in park. I...


The 2006 Vibe no longer has that feature. It was discontinued after 2005. I have the 2005 so I know how to change it. If your 2006 is able to change then here are the directions from my 2005.
Programmable Automatic
Door Locks
If you have an automatic transaxle, your vehicle is equipped with an auto door lock/unlock feature which enables you to program your power door locks.
Your vehicle left the factory programmed to Mode 4.
The following is a list of the available programming options:
Mode 1: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. There is no automatic door unlocking.
Mode 2: No automatic door locking or unlocking.
Mode 3: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the shift lever is moved to PARK (P) with the ignition on.
Mode 4: All doors and liftgate lock when the shift lever is moved out of PARK (P) with the ignition on and all doors and liftgate closed. All doors and liftgate unlock when the ignition switch is turned from ON to ACC or to LOCK.
To change the mode you are in, do the following:
1. Set the interior lamp control dial to the door position.
See Interior Lamps Control on page 3-16.
2. Move the shift lever into PARK (P) and close all doors and liftgate.
3. Turn the ignition to ON.
4. Within five seconds after the ignition is turned to ON, press and hold the power door lock switch in
the lock position for about five seconds.
5. The interior lamp will flash to indicate that the mode has been changed. For example, if the lamp flashes once, the function has been changed to Mode 1.
If the battery is disconnected or run down, the mode is changed to the initial mode which is Mode 4.

Jan 22, 2009 | 2006 Pontiac Vibe

1 Answer

How do I replace the Ignition lock?


Hi there, to remove the ignition lock, remove the steering colomn trim, insert the key and turn to position 2, there is a small button under the lock press this and pull the key, this will remove the lock, you will have to switch the tumblers over to the new barrell so that it works with your original key

Dec 17, 2008 | 1999 Jeep Grand Cherokee

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

109 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8265 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...