Question about 2002 Audi A4

1 Answer

Trouble Codes I have the following codes: 19497 P3041 18032 P1624 01039 01304 P0761 can anyone please tell me which need to be fixed and what exact parts need to be fixed?

Posted by on

  • devinotsuka Feb 03, 2010

    so for number 1 and 3 do i need a new collant temp sensor and rewire it? 4 is just radio meaning the wiring behind the stereo or attena? number 5 and 4 what do i need to fix?

  • devinotsuka Feb 03, 2010

    so for number 1 & 3 all i need to do is replace the coolant temp sensor and wiring for it? opr one or the other? number 4 is the radio wiring to the stereo or attena? what do i need to do for 5 and 2? i have no idea

×

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,874 Answers

1. VW VAG type 5 digit fault code 19497 = EOBD type P3041 fault code:
Fault location = CAN data bus, instrumentation - implausible Engine Coolant Temperature (ECT) signal
Probable cause = Wiring, matching resistor in Engine Control Module (ECM)

2. VW VAG type 5 digit fault code 18032 = EOBD type P1624 fault code:
Fault location = Malfunction Indicator Lamp (MIL) - request signal active
Probable cause = Trouble code(s) stored in other system(s)

3. VW VAG type 5 digit fault code 01039:
Fault location = Coolant Temperature Sensor (G2)
Probable cause = Open or Short to Plus, Short to Ground - Intermittent

4. VW VAG type 5 digit fault code 01304:
Fault location = Radio
Probable cause = No Communication

5. EOBD type P0761 fault code:
Fault location = Shift Solenoid C
Probable cause = Performance or Stuck OFF

Posted on Feb 03, 2010

Testimonial: " "

  • TDISLine
    TDISLine Feb 03, 2010

    For number 1 and 3 you need check up wiring, and if good then replace the Engine Coolant Temperature (ECT) sensor (G2).

    For number 2 only erase all faults from all ECU systems after damaged components replacement.

    For number 4 check up radio electrical cables and in most cases antena connexion (radio without communication).

    For number 5 check up supply wiring and Shift Solenoid (SS) C - performance or stuck of.



×

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

99 olds alero abs trouble codes


looks like all 4 brakes need checked..

Dec 27, 2013 | 1999 Oldsmobile Alero

1 Answer

96 taurus ax4n tranny


You might need to replace the valve body clip with the upgraded (stronger) one. Ford had problems for a while with the clip breaking and not allowing the tranny to shift into O/D. I had the no O/D problem, I replaced the clip with the upgraded (stronger) one which fixed the problem.

fix with this kit
Sonnax 96206-07K AX4N 4F50N Transmission forward control valve, Transmissionpartsusa.com

Below are the DTC codes if it has any. ISSUE
No 4th gear operation (no 3-4 shift) and Diagnostic Trouble Codes (DTCs) P0734 and/or P0761 or 648 may occur on some vehicles.

Nov 19, 2013 | 1996 Ford Taurus

1 Answer

I have a 1998 Nissan Maxima GLE, I Failed the Emission Inspection (DTC) Diagnostic Trouble Codes of "P1492","P1105" What these Codes exactly? mean


A code P0300 may mean that one or more of the following has happened:
  • Faulty spark plugs or wires
  • Faulty coil (pack)
  • Faulty oxygen sensor(s)
  • Faulty fuel injector(s)
  • Burned exhaust valve
  • Faulty catalytic converter(s)
  • Stuck/blocked EGR valve / passages
  • Faulty camshaft position sensor
  • Defective compute
  • P1105MAP/BARO Pressure Switch Solenoid Valve
  • Check and clean the MAP sensor, or replace.
  • P1492EVAP Canister Purge Control/Solenoid Valve (Circuit)
  • Replacing the purge solenoid will clear code P1492 This should also clear code P0300 as well.

Oct 16, 2012 | 1998 Nissan Maxima

1 Answer

2003 ford f150 running rough, check engine light is on.


Get a cheap code reader(a basic one is about 50 bucks).It won't exactly tell you what's broken,but it will lead you in the right direction.(or,you can take it to some parts stores and get a free reading).Having your own is nice,though,because some repairs require reading the code,try something(like swapping ignition coils to see if the trouble follows the part or not),and then fixing it and clearing the code for good.

Sep 16, 2012 | Cars & Trucks

1 Answer

Have a 2002 Isuzu rodeo, the check engine light tells me ignition coil misfire.I just had an aftermarket installed a while back. Now mechanic tells me it needs the original part and not an aftermarket...


Do you have the exact code? An aftermarket coil can still fail, especially if it is not designed for your ignition system and the output/input readings expected by the ECM. No matter what, it is worth a try, it is not difficult to change it out. But I would still like to know what the actual code is.

Dec 30, 2010 | Isuzu Rodeo Cars & Trucks

1 Answer

Failed OBDII Diagnstic trouble codes P0761 and O1744 What does this mean?


code P0761-
Possible causes - Low transmission fluid level
- Dirty transmission fluid
- Faulty shift solenoid 3 valve
- Shift solenoid 3 valve harness or connectors
- Shift solenoid 3 valve circuit is open or shorted
P0761 FORD Description Shift solenoid valve 3 is turned ON or OFF by the Transmission Control Module (TCM) in response to signals sent from the park/neutral position (PNP) switch, vehicle speed and Engine Control Module (ECM) (throttle opening). Gears will then be shifted to the optimum position. When is the code detected? The P0761 code is detected when the ECM has detected a mechanical fault with the solenoid energized, valve stuck off code O1744- is not a code these are the ones I have found that come close
P0174 1999 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2000 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2001 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2002 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 2003 FORD WINDSTAR Fuel Injection System Too Lean Bank 2 P0174 FORD Fuel Injection System Too Lean Bank 2

Sep 28, 2010 | 1999 Ford Taurus

1 Answer

2003 Audi A6 gives the code P3041. What's wrong with my car?


EOBD type: P3041 = VAG type 5-digit: 19497
Fault location: CAN data bus, instrumentation - implausible ECT (Engine Coolant Temperature sensor) signal
Probable cause: Wiring, matching resistor in ECM (Engine Control Module)

Sep 03, 2010 | 2003 Audi A6

2 Answers

Fault code on my vw mk4 19497 implausible engine temp. message from inst panel p3041


VAG TYPE 5 DIGIT 19497 EOBD TYPE P3041 FAULT LOCATION CAN DATA BUS INSTRUMENT-IMPLAUSIBLE ECT SIGNAL PROBABLE CAUSE WIRING MATCHING RESISTOR IN ECM

Mar 04, 2010 | 2003 Volkswagen Golf

2 Answers

Vehicle wont change up into gear reverse gear not


P0734 - 4th gear incorrect ratio. P1529 Malfunction Indicator Lamp Request. Problem is in the transmission.
Take/Tow your vehicle to an authorized Hyundai dealership and pay the diagnostic fee... they will tell you exactly what the problem is and the cost of parts/labor to fix it... at least this way you'll know what the problem is and what's required to fix it.

Sep 27, 2009 | 2002 Hyundai Accent

1 Answer

CHECK ENGINE LIGHT IS ON AND SO IS THE AIR BAG LIGHT


I recommend taking your car to your local auto parts store like AutoZone. They will hook up their diagnostic computer free of charge and generate your error codes. They can also decode the codes and tell you what may be the proximate cause. Same thing the VW Dealer will do for a charge of $65 (but AutoZone is FREE). One of the codes probably relates to a bad seal on your gas cap (try removing, cleaning and replacing). One of the other codes might be indicative of a bad oxygen sensor. They cost $20+, so you want to be certain before you start a replacement. There are between 2-3 oxygen sensors on your car.

Sorry I couldn't be more descriptive.

Jun 30, 2009 | 2003 Volkswagen New Beetle Convertible

Not finding what you are looking for?
2002 Audi A4 Logo

Related Topics:

4,314 people viewed this question

Ask a Question

Usually answered in minutes!

Top Audi Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

yadayada
yadayada

Level 3 Expert

80637 Answers

Thomas Perkins
Thomas Perkins

Level 3 Expert

14417 Answers

Are you an Audi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...