Question about 2003 GMC Yukon Denali

1 Answer

How do you know if you have need a stering pump

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,752 Answers

When it makes noise, it's hard to run the steering wheel, and/or it leaks.

Posted on Feb 03, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Steerin wheel hard to turn


Hi I can't give sn accurate answer with knowing what the vehicle is! A few things you can check if hydrolic stering. Is there fluid in the resivour? Is the belt turning the pump?? Are there any visible leaks??? If its electric stering are there any lights on the display, if so go to a mechanic to get it diagnosed. Regards Jim...

May 20, 2015 | 2001 Ford Taurus

1 Answer

Power stering pump 2008 f150


You will need basic hand tools. First take off the serpentine belt. Unhook the high and low pressure lines, they should be toward the rear of the pump. Remove the four bolts securing it to the engine. Replace the pump and make sure to refill fluid.--------------------------------------------------------------------------------
Digiprog3 Odometer Correction Tool

Mar 28, 2013 | Cars & Trucks

1 Answer

Mercury Sable 99 power stering problem


ALL FORDS WILL DO THAT THERE IS NO BY PASS IN GEAR BOX OR RACK , WITH ENGINE OFF THEY WILL OVER FLOW. ONLY FORD SORRY TO SAY YOU FIX IT BUT IS ALL THE SAME ..

Feb 16, 2013 | Mercury Sable Cars & Trucks

1 Answer

Power srering fluid turned clay color


Yes, this is a problem. The clear power steering fluid is a mineral oil base and the red Lucas additive is petroleum base. Your car uses the red petroleum base, which is actually Dexron ATF (automatic transmission fluid). Lucas is great stuff, the person at the parts store just doesn't know their stuff. You need to flush the system to save your pump from going out very prematurely.

Jan 28, 2013 | Cars & Trucks

1 Answer

Have a bad stering angle sensor on a 2006 grand cherokee do you have to re program the system after you change the sensor


not sure i know you do on a renault to the straight ahead position but this is a special electric motor under the dash ,if this has a hydraulic pump then i wouldnt think so

Oct 05, 2012 | 2006 Jeep Grand Cherokee

1 Answer

I am leaking power stering fluid, is it best to replace the power stering pump or overhaul it replace the gasket


where is the leak coming from gear box or pump,if its the pump,replace whole pump

Mar 25, 2010 | 1998 Dodge Dakota

1 Answer

I need to replace my power stering pump on my 1995 surburban


Removal/Installation Notes
  1. Disconnect hoses at power steering pump, then plug pump ports and hoses to prevent dirt entry.
  2. Loosen pump adjusting bolt and remove pump drive belt.
  3. Remove pump to support bracket retaining bolts, then the pump.
  4. Reverse procedure to install.

May 20, 2009 | 1995 Chevrolet Suburban

1 Answer

Power stering pump


Is this the 3.4L DOHC engine or the 3100/3400 engine?

Oct 17, 2008 | 1997 Chevrolet Monte Carlo

1 Answer

Stering pump ? for 1993 jeep cherokee 4.0 .


Loosen 2 pivot bolts on back of pump, 13mm. then loose one bolt on bottom/front. Turn adjustment bolt on right side/bottom of pump to loosen belt. Once belt if off, remove all of the bolts connection pump to engine bracket. Remove hoses going to pump. Install new one, filled up with fluid. Now you have to bleed air out of sys. Move steering wheel left/right to the stops. Do this about 10 times either direction.

Aug 06, 2008 | 1993 Jeep Cherokee Country

Not finding what you are looking for?
2003 GMC Yukon Denali Logo

Related Topics:

77 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76109 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...