Question about 1997 Oldsmobile Achieva

1 Answer

1997Acheiva 2.4L fuel leaking at pressure regulator, why?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 279 Answers

The regulator has a rubber o-ring that seals it to the fuel rail, It can also be a defective diaphram inside the regulator.I would suggest that you replace the regulator.

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1999Buick regal gs. Car shut off like it wasnt getting fuel changed filter got me home ran fine then cranks stuts back off like no fuel again blak flood smoke coming out exhaust


Use a fuel pressure gage, check for proper fuel pressure, key on engine off. Then with key off, see if pressure will hold for a bit? If the pressure drops like a rock, check for a fuel pressure leak, check for fuel injector leak and fuel pressure regulator leak. If fuel pressure regulator is connected to fuel rail and has a vacuum line, check to see if gas in the vacuum line, if so, pressure regulator is faulty.

Check for applicable trouble codes? How long since a tune-up?

Oct 28, 2015 | Cars & Trucks

1 Answer

Fuel rail leak


fuel rail contains o'ring and seal washer. the fuel regulator is at end of rail

Oct 17, 2013 | Chevrolet Prizm Cars & Trucks

1 Answer

Im gonna rplace the fuel pressure regulator. In the haynes manuel it says that you need to remove the fuel rail. Ive asked a few people and they said they dont think it is necassary it is an 03 impala. ...


Not sure why Haynes says to do that. below is instructions from autozone.com, and none of the engines require the fuel rail to come off. That said, if you have the 3.4, you may need to pull the upper intake manifold.


Removal & Installation The need to work as cleanly as possible cannot be over-emphasized. Even the smallest amount of dirt, if allowed into the fuel pressure regulator and/or the fuel rail, will find its way to the fuel injectors. The nozzle openings of the injectors are very small. Keep hands and tools clean. Clean the areas to be disconnected with a suitable solvent. Carefully cover open fittings and connections to keep out foreign material. Dirt in the injectors almost guarantees a clogged fuel injector and engine performance problems.

3.4L (VIN E) Engines

  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Remove the upper intake manifold assembly.
  4. Disconnect the vacuum line from the pressure regulator.
  5. Remove the regulator retaining screw and remove the retainer bracket. Using a clean shop cloth to catch fuel spillage, carefully pull the regulator from the fuel rail. Twist the regulator slightly while removing to ease removal. Discard the O-ring.

    0996b43f802307fd.jpg enlarge_icon.gifenlarge_tooltip.gif

    Fig. Exploded view of the fuel pressure regulator mounting-3.4L (VIN E) engines


To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate a new pressure regulator O-ring with clean engine oil and install on the regulator inlet.
  4. Install the fuel return pipe to the regulator.
  5. Install a new retainer and spacer bracket into the slot on the fuel rail and install the pressure regulator to the fuel rail. Tighten the fuel return line nut to 13 ft. lbs. (17 Nm).
  6. Connect the vacuum line to the pressure regulator and install the retainer screw. Tighten to 76 inch lbs. (8.5 Nm).
  7. Inspect and verify that the retainer and spacer bracket is engaged in the slots in the fuel rail. Grasp and pull on the regulator to ensure that it is properly seated.
  8. Install the upper intake manifold.
  9. Connect the negative battery cable.
  10. Inspect for leaks using the following procedure:
    1. Turn the ignition switch to the ON position for 2 seconds.
    2. Turn the ignition switch to the OFF position for 10 seconds.
    3. Turn the ignition switch to the ON position again.
    4. Inspect all areas for fuel leaks.

3.8L Engines
  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Clean any dirt from the fuel pressure regulator retaining ring.
  4. Remove the vacuum hose from the pressure regulator.
  5. Remove the snaprings. Twist the regulator slightly and pull the pressure regulator from the fuel rail. Use a shop towel to catch fuel spillage as the regulator is removed.
  6. Remove the O-rings and O-ring back-up.

To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate the new pressure regulator O-rings with clean engine oil. Install the O-ring back-up, the large O-ring and then the small O-ring. Install the pressure regulator and secure with the snapring.
  4. Attach the vacuum hose.
  5. Connect the negative battery cable.
  6. Inspect for leaks using the following procedure:
    1. Turn the ignition switch to the ON position for 2 seconds.
    2. Turn the ignition switch to the OFF position for 10 seconds.
    3. Turn the ignition switch to the ON position again.
    4. Inspect all areas for fuel leaks.

  1. Disconnect the negative battery cable.
  2. Relieve the fuel system pressure.
  3. Clean any dirt from the fuel pressure regulator retaining ring.
  4. Remove the vacuum hose from the pressure regulator.
  5. Remove the snaprings. Twist the regulator slightly and pull the pressure regulator from the fuel rail. Use a shop towel to catch fuel spillage as the regulator is removed.
  6. Remove the O-rings and O-ring back-up.

To install:
  1. Clean all parts well. DO NOT use shop compressed air to test or clean a fuel pressure regulator. Clean the fuel pressure regulator screen, if necessary. DO NOT immerse the fuel pressure regulator in a solvent bath or it will be damaged.
  2. If the filter screen has been contaminated, it should be removed and the pressure regulator replaced.
  3. Lubricate the new pressure regulator O-rings with clean engine oil. Install the O-ring back-up, the large O-ring and then the small O-ring. Install the pressure regulator and secure with the snapring.
  4. Attach the vacuum hose.
  5. Connect the negative battery cable.
  6. Inspect for leaks using the following procedure:
    1. Turn the ignition switch to the ON position for 2 seconds.
    2. Turn the ignition switch to the OFF position for 10 seconds.
    3. Turn the ignition switch to the ON position again.
    4. Inspect all areas for fuel leaks.

Mar 16, 2011 | 2003 Chevrolet Impala

1 Answer

Have trouble code 45 on a 1993 s10 blazer 4.3l. Have replaced oxygen sensor, did not help


1994 Chevrolet S10 Blazer 4.3L, Vin W Customer Concern: DTC 45 The spark plugs are black on both banks. Right bank plugs are damp. Removed the tuning valve and looked inside the plenum. Can see a washed/clean area on the right side. Fuel pressure is good, it holds when the pump stops. Tests/Procedures: 1. Remove the upper intake plenum cover and inspect for a fuel leak at the fuel pressure regulator.

2. Inspect the fuel pressure regulator and return lines and fittings at the left side of the plenum.

3 Replace the Central Multipoint Fuel Injection (CMFI) unit. Potential Causes: Leaking Fuel Line - One or more may have a problem.
Leaking Fuel Pressure Regulator
Tech Tips: The fuel pressure regulator may only leak at a cold or hot engine, only with vacuum applied, or only without vacuum applied. The leaking at the fuel lines and fittings have as often been the result of repairs as the initial cause of the problem. Handle the lines and fittings carefully. The fuel pressure regulator is a integral part of the Central Multi-port Fuel Injection (CMFI) unit. Any failure requires entire unit replacement.

Mar 03, 2011 | Chevrolet Blazer Cars & Trucks

1 Answer

I need to replace de fuel presurre sensor in a pontiac montana ,do i have to just replace the sensor ,o the sensor came with the fuel pump?thank you


Replacing the fuel pressure regulator, involves just replacing the regulator at the end of the fuel rail in the engine compartment, but fuel pressure sensor - does this mini-van have a fuel pressure sensor?
replacing the fuel pressure regulator: (1) locate it at the end of the fuel rail in the engine compartment,
(2) relieve fuel system pressure (3) disconnect fuel pressure regulator vacuum line. (4) remove fuel pressure regulator retaining screw (retain for re-use (5) using a shop towel to catch spilled fuel, lift & twist Fuel pressure regulator to remove it from the fuel rail. (6) remove/discard retainer and spacer bracket from the fuel rail. (7) remove fuel pressure regulator from the engine fuel return pipe. (8) remove/discard Fuel Pressure Regulator inlet O-ring (9) Check Fuel Pressure Regulator filter screen for contamination - if contaminated, replace Fuel Pressure Regulator. (10) Lubricate new Fuel Pressure Regulator inlet O-ring with clean engine oil & install onto the Fuel Pressure Regulator inlet. (11) Install the fuel return pipe onto the Fuel Pressure regulator (12) Install new retainer & spacer bracket into the slot on the fuel rail.
(13) Install Fuel Pressure Regulator onto Fuel Rail & tighten Engine Fuel Return Pipe nut to 13 ft-lbs (17 Nm). (14) connect Fuel Pressure Regulator vacuum line, (15) Install Fuel Pressure Regulator attachng screw & tighten to 76 in-lbs (8.5 Nm). (16) Inspect & verify that retainer & spacer bracket is engaged in the slots on the fuel rail. Grasp & pull on the Fuel Pressure Regulator.
to ensure that the Fuel Pressure Regulator is properly seated. (17) inspect for fuel leaks with this
procedure: On 2sec,(holy rollers), off 10sec will be left on, inspect for leaks while running.

Dec 11, 2010 | 2000 Pontiac Montana

1 Answer

I have a 2004 Tahoe which has misfire problems (P0300). I changed the plugs, wires, fuel filter and air filter but problem still exist. The 4 plugs on the passenger side continue to file out and become...


Removal & Installation of fuel Regulators on
4.8L, 5.3L & 6.0L Engine To Remove:
CAUTION
Three styles of fuel pressure regulators and fuel rails will be used in this model year. Each regulator has a different "footprint" that consequently changes the size of the receiving port in the fuel rail. The regulator retaining clips are specific to each rail-regulator design and cannot be interchanged.
chevy_aval15_02-04_fuelrail.gif

  1. Remove the engine sight shield.
  2. Relieve the fuel system pressure. Refer to Fuel Pressure Relief Procedure.
  3. Clean the fuel pressure regulator retainer and the surrounding area.
  4. Remove or disconnect the following:
    • Fuel pressure regulator vacuum line.
    • Fuel pressure regulator retainer.
    • Fuel pressure regulator.
  5. Remove the following parts from the fuel rail:
    • Backup ring (10)
    • Regulator Seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
To Install:
chevy_aval15_02-04_retainer.gif

  1. Make sure the NEW fuel pressure regulator retainer is the right one.
  2. The tabs (1) are used on the straight vacuum port retainer (2), and the E85-straight vacuum port retainer (3).
  3. The angle vacuum port retainer (4) has no tabs. chevy_aval15_02-04_fuelrail.gif

  4. Install the following parts onto the fuel pressure regulator (9).
    • Backup ring (10)
    • Regulator seal O-ring (11)
    • Regulator filter (12)
    • Regulator seal O-ring (13)
  5. Lubricate the fuel pressure regulator O-rings with clean oil.
  6. Install the fuel pressure regulator and retainer. CAUTION
    Whenever the fuel pressure regulator is removed from the fuel rail NEW O-rings and a NEW retaining clip should be used on reinstallation.
  7. Connect the vacuum line.
  8. Tighten the fuel filler cap.
  9. Use the following to inspect for leaks:
    • Turn ON the ignition, with the engine OFF, for 2 seconds.
    • Turn OFF the ignition for 10 seconds.
    • Turn ON the ignition, with the engine OFF.
    • Install the engine sight shield.
8.1L Engine To Remove:
Fuel pressure regulator vacuum line gm_trk_sub15_fuel_press_reg_vac_line.gif

  1. Before servicing the vehicle refer to the precautions at the beginning of thjs section
  2. Remove the fuel injector sight shield as needed
  3. Relieve fuel system pressure (See: Fuel Pressure Relieving)
  4. Disconnect the fuel pressure regulator vacuum line (A) 8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  5. Clean any dirt from the fuel pressure regulator retainer and the surrounding area
  6. Remove the fuel pressure regulator retainer (I)
  7. Remove the fuel pressure regulator (H) from the fuel pressure regulator housing
To Install:
8.1L Fuel pressure regulator retainers gm_trk_sub15_81l_fuel_press_reg_retainers.gif

  1. Install or connect the following:
    • Backup ring (J) on the fuel pressure regulator (H)
    • New large O-Ring (K) on the fuel pressure regulator
    • Regulator filter (L) on the fuel pressure regulator
    • New small O-Ring (M) on the fuel pressure regulator
  2. Lubricate the fuel pressure regulator large O-Ring and the small O-Ring with clean engine oil
  3. Push the fuel pressure regulator onto the regulator housing on the fuel rail
  4. Install a new fuel pressure regulator retainer (I)
  5. Install or connect the following:
    • Fuel pressure regulator vacuum line
    • Negative battery cable
  6. Tighten the fuel filler cap
  7. Inspect for leaks using the following procedure:
    • Turn on the ignition with the engine off for two seconds
    • Turn off the ignition for 10 seconds
    • Turn on the ignition with the engine off
    • Inspect for fuel leaks
  8. Install the fuel injector sight shield
  9. Road test the vehicle to check performance
prev.gif next.gif

Sep 02, 2010 | Chevrolet Tahoe Cars & Trucks

2 Answers

When you turn the key on excessive fuel flows into the air intake. its a 1989 6 cylinder 3.1 fuel injected


You could have either an injector that is stuck open or a fuel pressure regulator that has developed a leak. A leaky injector will usually only leak fuel into one cylinder as it is located just above the intake valve in the lower part of the intake while a leaky fuel pressure regulator will leak fuel into the front end of the intake manifold [behind the throttle plates] and the fuel will acuumulate throughout the upper intake plenum. When a fuel pressure regulator develops a leak the fuel that is escaping from it flows through the small 1/8" diameter plastic vacuum line which goes from the top of the regulator to the intake manifold. Even a trace of fuel in this line means the regulator is bad. I've seen both leak items leak but probably replace 10 regulators leak for every one injector. Good luck, hope you find your problem!

Jul 22, 2010 | 1989 Oldsmobile Cutlass Supreme

1 Answer

Where is fuel pressure regulatore located


For 2000 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl
If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold.

The throttle body is mounted on it and your fuel lines terminate into the center of this.


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.
To install:


aaf5240.jpg
Fig. Fuel pressure regulator-4.2L engine
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.
  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.
Hope help with this (remember rated this post).

Feb 26, 2010 | 2000 Chevrolet Blazer

1 Answer

Leaking fuel pressure regulator


Release fuel pressure by removing fuel pump relay and turning engine over to release pressure. Place a rag to catch any fuel under regulator Fuel pressure regulator has a locking clip pry clip off remove vacuum line pull regulator out with twisting motion,replace fuel pressure regulator install clip connect vacuum line install relay. Check for leaks,your done.

Feb 23, 2010 | 2001 Pontiac Grand Am SE

Not finding what you are looking for?
1997 Oldsmobile Achieva Logo

Related Topics:

57 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...