Question about 1999 Chevrolet 3500

1 Answer

Removal of key and tumbler, does this require steering wheel removal.

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 7 Answers

YES IT DOES

Posted on Feb 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do I change the ignition cylinder on a 97 Chevy c1500 if can't turn key to on/run.


You need to remove the steering wheel , turn signal control and in the steering column you will find a pin that holds the tumblers in place for the key switch. You can remove the pin and then remove the key tumbler and replace it. Go to You Tube and they have videos on just what you need to do to remove the steering wheel and etc. Hope this helps.

Apr 03, 2015 | 1997 Chevrolet C1500

1 Answer

Do i have to remove the steering wheel to change the ignition switch on a 2002 cavalier


Ignition switch located half way down steering column.
Ignition tumbler (Where you insert the key) Need to remove steering wheel, if tilt steering need remove c clip, then there is a hex bolt securing the tumbler.
Ignition switch is a bit more involved.
hope this helps, James Booth

May 17, 2011 | Chevrolet Cavalier Cars & Trucks

1 Answer

Replaced the ignition key switch and now my steering wheel clicks when i turn it what do i do


I've seen the plastic covers not go together correctly and rub the steering wheel. try removing the Key and tumbler and turn the steering wheel. Is the noise gone? Sometimes the new tumbler will not pull back the steering wheel lock enough and it will rub alittle. Check the steering wheel lock to see if it's pulling all the way away from the steering wheel.

Jan 11, 2011 | 1996 Chevrolet K1500

2 Answers

2000 dodge caravan key will not turn can not start car steering wheel is locked


The tumblers in the lock cylinder are stuck and this prevents the key from turning. Spray some lubricant into the cylinder, insert the key in and out numerous times and also hit the end of the key with a rubber hammer while it is in the cylinder and this will help to release the tumblers.

Dec 27, 2010 | 2000 Dodge Caravan

1 Answer

Key stuck in ignition -- cannot turn on or off. Can an ignition switch cause the tumbler to lock up? Or does the ignition tumbler need to be replaced? If the ignition tumbler needs to be replaced, how...


lets start simple.get a can of silacone spray oil and spray into the switch and keep moving key and you will find this will reliese the key,if you need to remove the ign switch dont panic as its a simple enough job.Forget about steering wheel and whatever,simply remove the outer plastic cover then this exposes the switch at the back of switch is a plug with wires pull it away ,then below the key you should see a tiny screw undo, and make sure the steering lock is not under pressure,ie steering wheel free,when trying to remove switch move steering wheel back/forward and switch should pull out.good luck.adrian,,,,

Nov 25, 2010 | 1988 Chevrolet Celebrity

1 Answer

How do you remove the ignition switch on a ford 250 1994 model?


Do you mean the key and tumbler, or the switch down on the bottom of the steering column? If you mean the switch, just lower your steering column by removing the cover at the bottom of the dash, and then remove the 2 bolts on either side of the column. The switch is near the base of the column, and the rod that runs from the ignition switch goes into it.
If you mean the key and tumbler, you have to pull the steering wheel, remove the screws from the signal cam, and then remove the locking bolt that holds the tumbler. You will need a steering wheel puller to remove the snap ring, and to reinstall.

Sep 04, 2010 | 1994 Ford F250 Supercab

2 Answers

How to remove key switch 1998 buick


This requires a couple of special tools, you'll need a steering wheel puller set with a lockring removal tool.Remove the steering wheel and horn wire connection. Remove the locking ring from the steering shaft. Now, with the key inserted in the key tumbler, turn the key to the run position. After doing this you'll be able to push in the key tumbler locking pin located near the base of the tumbler. If you do not have a key or it is not turning, then it will become necessary to replace the entire collar assembly. The amount of damage that is necessary to turn a non-working key is enough to ruin the collar permanently. Thank You, Dana

Feb 13, 2010 | 1998 Buick Century

1 Answer

How can i replace the key switch in a 01 Grand AM and will i need to replace the security mod too?


It depends if you want to change the key barrel or the tumblers, to remove the tumbler set put key in the switch, remove the beauty ring it just snaps on then stick a paper clip into the hole where you removed the ring or on the bottom of the barrel turn the key in reverse past accessories and pull tumbler set out. if you need to remove the barrel you will have unhook the battery then take horn cover off, pull the protective plastic tabs off the rear of the steering wheel and remove the safety tork screws and remove the air bag disconnect the air bag plug. next remove the three screws holding the horn ground ring and the plastic piece that separates it from ground put them in order next remove the center bolt using a steering wheel puller pull steering wheel next compress the plastic cover with the U shaped steering wheel clap and push the plastic dust cover down 1/4 inch next remove the center c cer-clip slide the clip off of the steering wheel shaft remove the dust cover remove the copper tangs on the right side of shaft and you will see a #6 tork screw remove that one screw and the barrel will come out, on some models it's the only way to get the barrel out. If this helps plese rate me. I am a better mechanic than a typest.

Aug 07, 2009 | 2001 Pontiac Grand Am SE

2 Answers

1992 gmc ignation tumbler


You have to remove the steering wheel, and the turnsignal switch, and you will see a torx bolt that retains the tumbler.

May 12, 2009 | 1996 GMC Sierra

Not finding what you are looking for?
1999 Chevrolet 3500 Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76848 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...