Question about Honda Civic Coupe

1 Answer

Just bought a civic type r on 08 plate-when i put the headlamps on the dashboard illumination isnt very bright but is bright when driving in daylight

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Honda Master
  • 1,675 Answers

Somewhere there should be a adjuster for the brightness normally down on right hand side of dashbored will have a picture of a clock most cars have them hope this helps

Posted on Feb 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

No low beam. Good high beam. No day lights. What's wrong?


No on the fuse . The LH HDLP and RH HDLP fuse in the fuse block - under hood, supply battery positive voltage to both low and high beam lamps at all times. For manual operation, when the headlamp switch is in the ON position, the headlamp switch supplies ground directly to the headlamps and to the body control module (BCM) on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. The BCM uses this signal to determine if the conditions are present to illuminate the daytime running lamps or park lamps.
The headlamps may be turned on 2 different ways. First, when the driver places the headlamp switch in the ON position, for manual operation. Second, with the headlamp switch placed in the OFF position activating automatic lamp control (ALC).For ALC operation, the BCM receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under low light conditions the BCM grounds the headlamp relay control circuit energizing the headlamp control relay. The now closed relay supplies ground through the headlamp switch to the headlamps and the BCM on the headlamp low or high beam signal circuit, depending on the position of the headlamp dimmer switch. When the BCM grounds the headlamp relay control circuit it also grounds the park lamp relay control circuit illuminating the park lamps. The headlamp relay is grounded at G203.
Daytime Running Lamps (DRL)
The low beam headlamps operate at reduced intensity when in daytime running lamps (DRL) mode. The ground circuit to the switch side of the DRL relay has a resistor in-line to reduce the intensity of the low beam headlamps for DRL operation. The body control module (BCM) receives a signal from the ambient light sensor indicating a low or high ambient, outside, light level. Under daylight conditions the BCM grounds the DRL relay control circuit energizing the DRL control relay. The now closed relay supplies ground directly to the low beam headlamps and to the BCM on the headlamp low beam signal circuit. The low beam headlamps now illuminate with reduced intensity. The DRL relay is grounded at G203. Any time the headlamps are illuminated the DRL will not illuminate. Manual park lamps do not effect DRL operation.

Feb 23, 2016 | 2005 Chevrolet Equinox LS

1 Answer

How can the lights be disabled that stay on all the time ?


Have you tried replacing the headlamp power relay in the underhood fuse/relay box ?
Headlights Circuit Description
Voltage to the headlamp switch is available at all times from the HDLP SW fuse 7 through CKT 1940 (ORN). When the headlamp switch is turned to the HDLP position, the headlamp power relay coil is energized through CKT 352 (WHT). A signal is also sent to the body control module (BCM) that the headlamp switch is ON. When the headlamp switch is in the AUTO or PARK position, the ambient light sensor (located in the right speaker grill) senses either daylight or darkness and sends the signal to the BCM. When the Ambient Light Sensor detects a dark condition, the BCM produces a signal that will energize the headlamp power relay through CKT 352. The relay coil is grounded through terminal F7 connector 2 of the UBEC to CKT 350 (BLK) to G102. When the headlamp power relay is energized the relay supplies power to the LT HDLP and RT HDLP fuses. The RH low beam headlamp receives current through CKT 198 (DK BLU) from the RT HDLP fuse. The LH low beam headlamp receives current through CKT 712 (YEL/BLK) from the LT HDLP fuse. Both headlamp low beam bulbs are grounded by CKT 524 (PPL) through the UBEC to the multifunction switch (low position) contacts through CKT 10 (YEL) to the headlamp grounding relay in the body relay block through the normally closed contacts to CKT 1850 (BLK) to G200.

Dec 22, 2015 | 1998 Chevrolet S-10 Pickup

1 Answer

2006 buick allure , automatic low beams do not come on when key starts car


Headlamps
You can use the headlamps two different ways.
?€¢
Place the headlamp switch in the HEAD position for normal operations


?€¢
Place the headlamp switch in the OFF position for automatic lamp control (ALC) operation. During ALC the low beam headlamps are ON for daytime running lamp (DRL) operation in daylight conditions at reduced intensity or low beam headlamps ON at full intensity with exterior park lamps ON in low light conditions. The ambient light sensor is a light-sensitive transistor that varies its voltage signal to the body control module (BCM) in response to changes in the outside (ambient) light level. When the BCM receives this signal the BCM turns ON just the low beam headlamps at reduced intensity for the daytime running lamp (DRL) operation. A resistor wire is used (CKT312) to reduced the voltage which reduces the light intensity for the DRL's function. The ambient light sensor can also turn ON the low beam headlamps and the exterior lamps for automatic lamp control (ALC). Any function or condition that turns ON the headlamps will cancel the DRL operation (this means no reduced voltage to the low beam lights). Thirty seconds after you start the engine with the headlamp switch in the OFF position, the DRL will perform one of two actions:
?€¢
Illuminate the low beam headlamps at reduced intensity in daylight conditions


?€¢
Illuminate the low beam headlamps and exterior park lamps for low light conditions

The DRL operates when the ignition switch is in the RUN position, the parking brake is not set and the transmission is not in the PARK position When these conditions are met and the DRL ambient light sensor indicates daylight conditions the DRL will illuminate
Should have BCM scanned for DTC'S - diagnostic trouble codes , could have DTC'S stored in memory !
DTC B2645 Ambient Light Circuit
The body control module (BCM) monitors the ambient light sensor signal circuit in order to determine if the daytime running lights (DRL) or the auto headlights (ALC) should be turned ON in the AUTO mode. When the BCM senses the ambient light sensor voltage is between 1.75-4.9 volts, either the DRL will be commanded ON or the ALC will be commanded ON.

  1. Turn ON the headlamps.
  2. Ensure that the headlamp dimmer switch is in the LOW position.
Do both low beam headlamps illuminate?
Is only one low beam headlamp inoperative? YES / NO
IF no
  1. Disconnect the lamps switch assembly.
  2. Install a jumper between the headlamp switch headlamps ON signal circuit and ground.
Do the low beam headlamps illuminate?
Do the low beam headlamps illuminate?
Go to Step 18
Go to Step 7

7

  1. Remove the headlamp module.
  2. Install a fused jumper between battery positive voltage and the switched low beam voltage supply circuit.
Do the low beam headlamps illuminate?
Go to Step 8
Go to Step 11

8

Test for the following in the headlamp module control circuit:
?€¢
An open


?€¢
A poor connection


?€¢
A short to ground

Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 10

9

Inspect for a poor connection at the harness connector of the lamp switch assembly. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 14

10

Inspect for a poor connection at the headlamp module. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 15

11

Test for a short to ground in the low beam voltage supply circuit. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 12

12

Inspect for a poor connection at the harness connector of the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections and Connector Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 17

13

Inspect the inoperative low beam headlamp voltage supply and ground circuit for a high resistance, a short to ground, or an open. Refer to Circuit Testing and Wiring Repairs .
Did you find and correct the condition?
Go to Step 19
Go to Step 16

14

Replace the lamp switch assembly. Refer to Headlamp Switch Replacement .
Did you complete the replacement?
Go to Step 19
--

15

Replace the headlamp module. Refer to Relay Replacement in Wiring Systems.
Did you complete the replacement?
Go to Step 19
--

16

Replace the inoperative low beam headlamp. Refer to Headlamp Assembly or Headlamp Bulb Replacement .
Did you complete the replacement?
Go to Step 19
--

17

Replace the underhood fuse block. Refer to Testing for Intermittent Conditions and Poor Connections .
Did you complete the replacement?
Go to Step 19
--

18

Replace the BCM. Refer to Control Module References for replacement, setup, and programming.
Did you complete the replacement?
Go to Step 19
--

19

Operate the system in order to verify the repair.
Did you correct the condition?
System OK
Go to Step 3

IF

Sep 30, 2015 | Buick Cars & Trucks

1 Answer

The head lights keep on while the switch is off


Do you mean they stay on when the Headlamp Switch is off (and the vehicle is running), or do you mean they stay on when you turn the Ignition Switch off? The 1999 Windstar has DRL (Daytime Running Lights) which illuminate during daylight hours when the vehicle is running. This occurs whether or not the headlamp switch is on.

Nov 10, 2013 | 1999 Ford Windstar

1 Answer

2007 chevy silverado can not get running lights to work


If you are talking about the Daytime Driving lights, I believe they only come on if there is sufficient daylight present, the engine is running, and the headlamps and park lights also have to be in the "Auto" position. I think your model pickup illuminates the low beams for use as the Daytime lights.

Nov 28, 2010 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

No daylight driving lights and also passenger head light is bright and the drivers side is dim what will cause.and if its aground.where is it located.


Corrosion in the wire harness splices are quite common on Cavaliers. The front lighting harness will need to be closely inspected for water intrusion into the harness. Remove both headlamp housings and inspect the harness that runs between both headlamps near the "grill" area. Any spliced area's will appear as a bulge in the harness and should be opened and inspected. Water intrusion will appear bright green as the copper will be corroded.Repair any supsect areas and tape up the harness completely after confirming the repair. Sorry I cannot tell you which splice as there are mutiples. Good luck.

Mar 31, 2010 | 2001 Chevrolet Cavalier

1 Answer

Dashboard lights out after replacing headlamp switch..


Did the old switch melt the pluggin? Might be a bad connection on the switch. Or you new switch is defective.

Aug 16, 2009 | 1996 Dodge Ram 1500 Club Cab

2 Answers

Alarm warning sound bit no warning light on dash board, cmax


It maybe the seatbelt connection fault as some fords don't all have an illumination on dashboard

Jul 03, 2009 | 2004 Ford Focus

1 Answer

Dash and shifter lights in 1996 jeep cherokee wont light


Hello and welcome to FixYa . Locate the dial that controls the brightness of the dashboardlights. If the control is not immediately evident. Make sure the brightness control is turned on. If it is and the lights aren't working, the problem may be a bad fuse. Check the fuse that controls the dashboard lights Replace the fuse if necessary. If just one part of the instrument panel is not lighting up, then you have either a burned-out bulb or a wiring problem.

Passenger side kick panel fuse breakdown for a 1996 jeep Cherokee Country

01 - 25A Rear Wiper/Washer
02 - 15A Radio, Cigar Lighter
03 - Empty
04 - 15A Passing Light
05 - 30A Blower Motor
06 - 30A (Circuit Breaker) Power Windows
07 - 02A ABS
08 - 20A Turn Signal Flasher
09 - 10A Radio/Clock Memory, Courtesy Lights, Glove Box, Cargo, Dome Lights, Telltales
10 - Empty
11 - 25A Headlamp Delay Module, Horn
12 - Empty
13 - 20A Power Door Locks
14 - Empty
15 - 15A Instrument Panel Lamps, Clock/Radio and Memory, Headlamp Switch, Parking Lamps
16 - 30A (Circuit Breaker) Power Seats, Trailer Tow
17 - 7.5A Instrument Cluster Gauges, Headlamp Delay Module, Chime Module, Overhead Console
18 - 25A Rear Defrost
19 - 05A Instrument Panel Lamps, Radio Illumination
20 - 5.5A (Circuit Breaker) Windshield Wipers and Washers

This should get you going. And you can always Ask Me.

Apr 27, 2009 | 1996 Jeep Grand Cherokee

Not finding what you are looking for?
Honda Civic Coupe Logo

Related Topics:

83 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76691 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...