Question about 1997 GMC Jimmy

1 Answer

I dont have er or lower break lights the top break light is working

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • GMC Master
  • 655 Answers

Bulb is probably burnt out.

Posted on Feb 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Taillight fuse location


ARE YOU SURE THERE ISNT TWO BULBS ONE FOR TAIL LIGHT AND ONE FOR BREAK LIGHT

Apr 26, 2014 | Chevrolet Silverado 2500HD Cars & Trucks

1 Answer

Two lower break lights not working (top on in the back window is)


Power for the brake lights travel thru a light failure sensor which could have failed. The third brake light does not involve the sensor.
If both brake light bulbs have no voltage, the sensor may have failed.

Aug 08, 2012 | 1995 Toyota Camry

1 Answer

2004 Cadillac CTS break lights


Hello! There is a relay called the BAS relay (brake assist) that controls both the top brake light and the lower lights...Since the top light works the relay is doing its job...However, the relay output is connected to several White wires that carry the same voltage to all brake lights...One of those White wires (the one that carries voltage to the lower lights is open)...There is a Joint Connector located with the BAS relay in the Left rear fuse block...One White wire coming in from the relay contact and 3 White wires leaving...#1 to the top brake light...#2 left brake light and #3 right brake light...It would appear that the junction of #2 and #3 are open inside the Junction block...Not the easiest fault to find and fix...
If you have a multimeter I'll guide you through the process...Or you can take it to a wiring specialist...Wiring Junction blocks look like hair combs (multi-tooth metal combs that push into a connecter with several wires all the same color...In this instance WHITE WIRES...When someone depresses the brake pedal +12 volts must be on all three white wires...Send a comment...Guru...saailer

Dec 11, 2011 | Cars & Trucks

1 Answer

My top break light works all the time....but the other break lights dont come on unless i use my turn signal.....also my running light do work properly.....why would just the brake lights not work when the...


the brake light switch is located in top part of the brake pedal and it controls all brake ligts the top and bottom lights use diferent power line, both come from brake light switch.

Feb 03, 2011 | 1997 Oldsmobile Cutlass Supreme

1 Answer

My breake light came on today. I've check the fluid and the ER break and the both are fine. My break squick a little but I been braking fine. Should I be alarmed?


If you have Significant Wera On the Read BRAKE SHOES This will Cause the BRAKE Light to Illuminate ALSO a FAULTY Brake LEVEL Sensor will Cause it

Aug 15, 2010 | 1987 Toyota Pickup

1 Answer

The upper break light comes on only when you push the break padde all the way and very hard, the lower break does not work at all


Sounds like you have a bad/defective brake light switch. When you apply brakes, the brake applies pressure to a switch like what is on your dryer or refrig. When it is pressed it turns on the brake lights. It is most likely defective mainly on the bottom lights and getting close to going completely out since your top still works. The mechanism inside the switch has broke or brken contact wires.

Jan 17, 2010 | 2003 Land Rover Freelander

1 Answer

1998 S10 rear break lights and blinkers do not work.


GROUND WIRE ON FRAMERAIL Behind Driver side REAR WHEEL << They Have A BAD TRACK RECORD,, They LOOSE CONTACT and Cause this Problem

Nov 02, 2009 | 1999 Chevrolet Suburban

2 Answers

Break light problem


If you have a test light, check the brake light switch (usually mounted at the top of the break pedal arm). The switch will have voltage on one wire....when the pedal is pressed, the switch closes the circuit and sends voltage to the other wire connected to the brake lights.

Jun 30, 2009 | 1998 Acura TL

Not finding what you are looking for?
1997 GMC Jimmy Logo

Related Topics:

22 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...