Question about 2000 Volkswagen Beetle

1 Answer

Headlight replacement and getting the assemble installed correctly.

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    New Friend:

    An expert that has 1 follower.

    Cheetah:

    An expert who has answered 20 or more questions within one hour.

  • Expert
  • 111 Answers

Hey this is tedious but with much patience the assembly will go back in. Make sure the lever you lifted to get the assembly out is still up and just keep lining up the slots with the groves in the assembly and with much prayer it will go in.

Posted on Mar 17, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Replace headlamp 1998 V70


If you're talking about just the bulb, it's very easy and will require no tools. If you're talking about the whole headlight assembly, that's pretty easy, and I believe all that is required is a 10mm socket, and maybe an extension. If I remember correctly there's 3 bolts that hold it in place. Be careful when removing the assembly as the side marker assembly tabs into the headlight assembly, and it's pretty common to break 15 year old brittle plastic tabs. Install the new assembly and adjust it as best you can until you can get it aligned professionally.

Jan 26, 2013 | 1998 Volvo V70

3 Answers

Replace headlight bulb


  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
  27. PLS VOTE ME
BMW e46 HID Headlight Replace
replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-0.jpg

replace-headlight-bulb-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 23, 2012 | 2000 GMC Denali

2 Answers

How do I get to the front headlight to change it


Re: Replace headlight bulb

  1. INSTALLATION GUIDE:
  2. BMW E38 99-01 HID TYPE 7 Series 1PC Halo Amber Projector Headlights
  3. Parts Identification:
  4. Projector Headlight
  5. Halo & L.E.D.
  6. Bottom of the Headlight:
  7. Ballast Bracket, Halo Wires(red/black)
  8. Turn Signal Adaptor
  9. TOOLS REQUIRE
  10. 10mm - 8mm socket
  11. Philip Screwdriver
  12. Crimper/Pliers
  13. For more information about how to install your vehicle, come visit our youtube page on
  14. http://www.youtube.com/spyderauto
  15. Remove the facotry headlight from the BMW. First remove the front panel cover below the headlight to access the bottom screw of the headlight housing. There is also two screws on the top of the housing.
  16. Once you have remove the headlight, turn the headlight around and remove the bracket that holds the Ballast. Then remove the ballast using a philip screwdriver.
  17. Unplug the wire from the ballast, and then remove the Xenon Plug from the housing. Put the Ballast aside.
  18. Carefully remove the D2S Xenon Bulb from the factory housing. Once you have remove the bulb, transfer the bulb to the Spyder headlights.
  19. Remove the bracket from the Spyder Headlight, and then install the ballast on the housing like the original. Once you have put the ballast on, put the bracket back on.
  20. Remove the Panel Cover bracket from the original headlight to the new Spyder Headlights as shown here.
  21. STEP:
  22. Install the Spyder turn signal socket if the orignal does not fit, unplug the factory plug from the harness and plug the new one on.
  23. Install the Spyder Headlight back on to the vehicle. Plug the Harness back on, the halo/L.E.D. Wires is connect to the Parking lights. These wires are optional to your vehicle, you do not have to wire them together.
  24. Factory Xenon Headlight
  25. Spyder Projector Headlight using Factory Xenon Lights
  26. STEP:
BMW e46 HID Headlight Replace
get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-0.jpg

get-front-headlight-change-afy5cnsznmokzumyhdcbeseq-5-2.jpg

Nov 22, 2012 | Cars & Trucks

2 Answers

How do you remove the headlights off a Pontiac grand am 2004


Lighting Headlight, Side Marker, Park & Turn Signal Assembly Removal & Installation To Remove:
  1. Open the hood.
  2. Remove the front air deflector.
  3. Apply light pressure to the headlight lens to hold the headlight in place while disconnecting the retainers.
  4. Lift up the headlight retainers to release the housing.
  5. Remove the headlight assembly, pulling straight forward from the headlight mounting panel. NOTE: Note the location and position of the adjuster retainers and locator tab.
  6. Disconnect the wiring harness from the headlight assembly.
  7. Rotate the bulb(s)/socket(s) as needed counterclockwise to release.
  8. Remove the bulb(s)/socket(s) from the headlight assembly.
To Install:
  1. Install the replacement bulb(s)/socket(s) to the headlight assembly rotating clockwise until fully seated.
  2. Connect the wiring harness to the headlight assembly.
  3. Position the headlight assembly to the mounting panel.
  4. Apply light pressure to the headlight assembly lens to hold the assembly in place while installing the retainers.
  5. Align the headlight assembly retainers and slide them over the assembly mounting tabs
  6. Install the front air deflector.
  7. Close the hood.
prev.gif next.gif

Feb 02, 2011 | 2004 Pontiac Grand Am

1 Answer

How to install a headlight


Locate the headlight bulb in the engine compartment, in the rear of the headlight assembly. It has a wiring harness connector attached to it.

Remove the wiring harness connector from the bulb. Release the locking tab on the connector and pull it off the bulb. Lay it aside

Locate the locking ring on the back of the headlight assembly. Turn the lock ring 1/8 of a turn counterclockwise to release the lock from the headlight assembly. Remove the lock ring and set it in a safe place.Remove the headlight bulb from the headlight assembly, pulling it straight back toward the engine. Discard the old bulb, unless you are reusing the bulbs in the Jeep.Insert a new bulb into the headlight assembly. (Be careful not to touch the glass when handling the bulb. The oils from your hands can cause it to overheat and shatter.)Install the headlight lock ring onto the headlight assembly and turn it clockwise 1/8 of a turn to lock the bulb into the assembly. Connect the wiring harness connector to the new bulb, ensuring that it seats completely on the bulb.Move to the opposite headlight and repeat the process to replace the second bulb. Turn on the lights to verify they are working correctly.

Jan 13, 2011 | 1993 Jeep Cherokee Country

1 Answer

How do I remove halogen low beam head light to replace it?


Removal & Installation To Remove:
WARNING
The halogen fog light bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope.
NOTE: The headlight bulb should not be removed from the headlight assembly until just before a replacement bulb is installed. Removing the bulb for an extended period of time may affect headlight bulb performance. Contaminants may enter the headlight assembly where they can settle on the lens and reflector. Never turn on the headlights with the bulb removed.
  1. Before servicing the vehicle, refer to the precautions in the beginning of this section. NOTE: Make sure that the headlight switch and the ignition switch are in the OFF position.
  2. Remove the pin-type retainers, screws and the air deflector from the radiator.
  3. Remove the three bolts and the headlight assembly.
  4. Disconnect the electrical connector.
  5. Remove the cover from the rear of the headlight assembly.
  6. If equipped with HID, release the spring tabs to remove the low beam bulb, otherwise disconnect the electrical connector and remove the bulb.
  7. Disconnect the electrical connector and remove the high beam bulb.
HID low beam headlight bulb lin_tc_0085.gif

Standard low beam headlight bulb lin_tc_0086.gif

High beam headlight bulb lin_tc_0087.gif

To Install:
  1. Place the headlight assembly in the proper position.
  2. Install the cover from the rear of the headlight assembly.
  3. Connect the electrical connector.
  4. Install the three bolts and the headlight assembly.
  5. Install the radiator air deflector.
prev.gif next.gif

Dec 18, 2010 | 2003 Lincoln Town Car

1 Answer

Replace headlight


Open the hood, There will be some phillip head screws on the top of the headlight Assembly. After taking the screws out, the head light assembly will pull straight out. Replace bulb and replace assembly. Carefully to get the tabs on the assembly back into the slots when installing the assembly.

Dec 17, 2010 | 2002 Pontiac Grand Prix

1 Answer

How do I get the headlight cover off to replace the bulb?


there should be two ten mm bolts to remove then look to see if there is a metal pin/rod that aligns the headlight assembly on outer side you might have to wiggle it and pull straight out they get stuck often when re-installing make sure metal pin/rod aligns with hole to keep headlamp adjusted if not installed correctly headlamps wont be aligned.

Mar 23, 2010 | 2006 Pontiac G6

2 Answers

Changing the headlight bulb in 2003 dodge grand caravan


1) open the hood.
2) Carefully remove the three screws holding the headlight assembly in place.
3) Carefully slide the headlight assembly out. At this point you can replace the headlight bulb, turn signal bulb, or the entire headlight assembly. To replace the headlight bulb turn the collar holding the bulb in counter clockwise. Pull the bulb out of the headlight assembly. Replace the bulb. Insert the bulb into the headlight assembly insert the collar and turn clockwise until it locks. (Do not touchglass with your fingers or it will cause the bulbs to catastrophically fail - clean with alcohol pad if you touch the glass)
4) Carefully insert the headlight assembly back into place.
5) Replace the three screws removed in step 2 being careful not to over tighten.

Oct 30, 2009 | 2003 Dodge Grand Caravan AWD

1 Answer

Driver light out how to replace bulb need special tools?


Headlight Bulb Removal & Installation To Remove:
  1. Disconnect and isolate the negative battery cable.
  2. Remove the headlight assembly mounting screws.
  3. Pull the assembly forward and disconnect the bulb connector.
  4. Turn the bulb retainer ring counterclockwise and remove the bulb from the headlight assembly.
To Install:
NOTE: Do not handle the glass portion of the bulb with your bare fingers.
  1. Install the bulb in the headlight assembly.
  2. Install the retainer ring.
  3. Connect the connector to the bulb.
  4. Install the headlight assembly in the vehicle.
  5. Connect the negative battery cable.
No special tools required.

Jun 24, 2009 | 2004 Dodge Caravan

Not finding what you are looking for?
2000 Volkswagen Beetle Logo

Related Topics:

111 people viewed this question

Ask a Question

Usually answered in minutes!

Top Volkswagen Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22246 Answers

yadayada
yadayada

Level 3 Expert

76846 Answers

Jeffrey Turcotte
Jeffrey Turcotte

Level 3 Expert

8548 Answers

Are you a Volkswagen Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...