Question about 2000 Jeep Grand Cherokee

Open Question

2 sets of 3 beeps every so often

On occasion the vehicle will do 2 sets of 3 beeps. Usually when I hear beeps, there is a message on the overhead display. When I hear a bell (ding) it is usually an idiot light on the dash. Not this time. Its 2 sets of 3 beeps and I see no lights or messages. Thanks.
Steve.

Posted by on

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Overhead DVD player in 2008 Toyota Sienna does not show the picture. Sound works.


Hello, I hope this helps. If no change then you probably have a hardware/ wiring issue and the dvd player may need to come out. Please advise
1. Confirm the DVD RSE system is inoperative. (blank screen) 2. For vehicles with Toyota navigation system: Perform the following procedure to turn OFF the RSE Lock function. A. Press the INFO switch on the navigation unit. B. Press the "Screen Setting" touch button on the navigation display. C. Under the "Rear Lock" option, press the "OFF" touch button and then press "OK" in the upper right part of the display. D. Press the DVD switch on the RSE system (if a DVD is NOT already in the player, insert one) and confirm screen is ON and the system will play DVDs. 3. For vehicles without Toyota navigation system: Perform the following procedure to turn OFF the RSE Lock function. A. Push the Audio Control knob multiple times to cycle through the various options (Bass, Mid, Treble, etc.) until "REAR LOCK" is shown on the screen. B. Turn the Audio Control knob so the display says "OFF" next to "REAR LOCK". C. Press the DVD switch on the RSE (if a DVD is NOT already in the player, insert one) and confirm screen is ON and the system will play DVDs. 4. If the above procedure resolves the concern, explain the system operation to the customer.This procedure is described in the Audio/Video" section of the vehicle Owner's Manual. 5. If the above procedure does NOT resolve the concern, perform RSE diagnosis using the Technical Information System (TIS), 2006 model year applicable vehicle Repair Manual.

Jun 29, 2015 | 2008 Toyota Sienna

Tip

Ford service light procedure 1994-01


Windstar

1999-01

To reset CHANGE OIL SOON/OIL CHANGE REQUIRED message on the message center, press the SETUP control to access the System Check mode. Press and release the RESET button until IF NEW OIL HOLD RESET is displayed. Press and hold RESET button until OIL LIFE SET TO 100% is displayed.


Windstar


1997-98

To reset "CHANGE OIL SOON/OIL CHANGE REQUIRED" message on the Message Center, press "RESET" and "SETUP" controls at the same time. "OIL LIFE % HOLD RESET NEW" will be displayed. Press the "SETUP" control to access the System Check mode. Press "RESET" to start the system check. Press and hold the "RESET" control. Press "RESET" and "SETUP" to reset the system to 100%


Explorer,
Mercury
Mountaineer


1997-01

To reset the oil life feature on the Message Center, press and hold the "OIL CHANGE RESET" button until the system counts down (about 5 seconds). The Message Center will display "OIL LIFE RESET TO 100%"


Probe

with Analog Dash

1989-92

When "SERVICE" is illuminated on the Vehicle Maintenance Monitor on the overhead console, press the "SERVICE INTERVAL RESET" button located directly above the light.


Probe

with Digital Dash

1989-92

When "SERVICE" is illuminated on the Vehicle Maintenance Monitor on the overhead console, press the "SERVICE INTERVAL RESET" button located directly above the light.


Probe

with Digital Dash

1989-92

When "SERVICE INTERVAL CHECK" is displayed is displayed on the far left side of the instrument panel, press the "SERV OFF" button, located on the speed alarm keyboard, until three tones sound.


Thunderbird,
Mercury Cougar

with System Scanner

1986-88

When "SERVICE" appears on the Diagnostic System Scanner, press the "ODO SEL" and "TRIP RESET" buttons simultaneously. The "SERVICE" message will go out and three short beeps will be heard when the system is reset.


Thunderbird,
Mercury Cougar


1989-94

If "CHANGE OIL SOON" or "NOW" is indicated on the Monitor, turn the ignition on, but do not start the engine. Within 16 seconds, insert a paper clip into the cavity to the left of the display and depress. The display will flash; when it stops, the system is reset.















on Dec 07, 2009 | Ford Windstar Cars & Trucks

2 Answers

2006 Expedition overhead compass reads "N" when heading "E". Wonder how to reset it so it indicates the direction accurately.


Yes. Wish I could tell you which button for sure, but to reprogram the Compass you hold one of the buttons and drive in a circle one or two times to reacquire your position.

Apr 08, 2013 | 2006 Ford Expedition XLT

1 Answer

My 2007 Dodge cummins 6.7 is telling me to perform service and the catalyst is full. How do I fix this problem myself?


Intervention Regeneration Strategy - EVIC
Message Process Flow (Catalyst Full Message)
(6.7L Diesel Engines Only)

Your new Cummins 6.7L diesel meets all EPA Heavy
Duty Diesel Engine Emissions Standards, resulting in the
lowest emitting diesel engine ever produced.
To achieve these emission standards your vehicle is
equipped with state of the art engine and exhaust system.
The engine and exhaust aftertreatment system work
together to achieve the EPA Heavy Duty Diesel Engine
Emissions Standards. These systems are seamlessly integrated
into your vehicle and managed by the Cummins
6.7L engine Powertrain Control Module (PCM). The PCM
manages engine combustion to allow the exhaust system's
catalyst to trap and burn Particulate Matter (PM)
pollutants, with no input or interaction on your part.
Additionally, the overhead console in your vehicle has
the ability to alert you to additional maintenance required
on your truck or engine. Refer to the following
messages that may be displayed on your Electronic
Vehicle Information Center (EVIC):

WARNING!
A hot exhaust system can start a fire if you park over
materials that can burn. Such materials might be
grass or leaves coming into contact with your exhaust
system. Do not park or operate your vehicle in areas
where your exhaust system can contact anything that
can burn.

Perform Service
The 6.7L Cummins engine utilizes a Closed Crankcase
Ventilation (CCV) system, EGR Valve and a EGR Cooler.
This system filters and recycles gasses produced in the
crankcase during the normal combustion process. Perform
Service will be displayed on the overhead console of
your vehicle if the CCV filter, EGR Valve and EGR Cooler
is due for required maintenance. The CCV filter is located
on the top of the engine valve cover. For additional
information, see your local authorized dealer.
Catalyst Full See Owner Manual
Catalyst Full See Owner Manual will be displayed on the
overhead console of your vehicle if the exhaust particulate
filter reaches 80% of its maximum storage capacity.
Under conditions of exclusive short duration and low
speed driving cycles, your Cummins engine and exhaust
aftertreatment system may never reach the conditions
required to remove the trapped PM, if this occurs Catalyst
Full See Owner Manual will be displayed on the
overhead console in your vehicle. If this message is
displayed you will hear one chime to assist in alerting
you of this condition.
Catalyst Stat::::::::::80%
Catalyst Stat::::::::::80% will replace the message Catalyst
Full See Owner Manual after it is displayed for one
minute. The engine Powertrain Control Module (PCM)
will continue to monitor the amount of particulate matter
trapped in the particulate filter. This message indicates
the percentage of the particulate filter capacity that has
been used.

By simply driving your vehicle at highway speeds for as
little as 45 minutes you can remedy the condition in the
particulate filter system and allow your Cummins engine
and exhaust Aftertreatment system to remove the
trapped PM and restore the system to normal operating
condition.
Catalyst Stat:::::::::::80%, 90%, 99%
Catalyst Stat:::::::::::80%, 90%, 99% If you are unable to
drive your vehicle under these conditions for an extended
period of time after the initial warning notification,
the Engine PCM will continue to monitor the
particulate filter and will display the progression of
particulate filter usage (80, 90, 99%) on the EVIC message
center.

CATALYST FULL SERVICE REQD
If the particulate filter reaches 99% of it's capacity the
overhead console in your vehicle will chime twice and
display the message CATALYST FULL SERVICE REQD.
At this point the engine PCM will register a fault code,
the instrument panel will display a MIL light and the
engine PCM will derate the truck reducing its horsepower
and torque output.
The PCM derates the engine in order to limit the likelihood
of permanent damage to the aftertreatment system.
If this condition is not corrected and a dealer service is
not performed, extensive exhaust aftertreatment damage
can occur. In order to correct this condition it will be
necessary to have the truck serviced by your local
authorized dealer.

Feb 14, 2011 | 2007 Dodge Ram Truck

1 Answer

Reset power mirrors 2008 expedition limited


if your talking about when you start the vehicle and they set them selves on the door are your settings buttons. usually 1 and a 2 set your mirrors and seats to your liking after your where your want them push and hold in on the number your wanting for yourself you should hear a beep noise showing there set to test it turn of the vehicle and back on and push the button once. your seat and mirrors should set to your set up. hope this helps

Jan 24, 2011 | 2008 Ford Expedition

2 Answers

Hi, I have a check front tire pressure warning on my 2009 saturn vue hybrid I filled up the tire it's not low at all, how do I get rid of the indicator warning? Thanks Amanda


The TPMS light (Tire Pressure Monitoring System) for that vehicle should function as follows.

If the light is on and steady, it means that the pressure in one or more of the tires is too low, and if the light is flashing, then it indicates that one or more of the tires are over-inflated.

1. Turn the ignition key to the "On" or "Run" position but do not start the vehicle. (If the vehicle has an electronic keyless ignition then place the ignition switch in the "ACCY" position)

2. Press the "Lock" and "Unlock" buttons at the same time on the vehicles remote key fob, and keep holding the two buttons down until you hear the horn beep, and usually this takes around five seconds. The horn beep will indicate that the learn cycle has begun.

3. Re-learn the TPMS system. Deflate or inflate air into the driver-side front tire for approximately 8 to 10 seconds and then listen for the horn to beep one time. (the horn might beep before the 8 to 10 second re-learn, or it could even take as long as 30 seconds after)

4. Repeat steps 2 and 3 for the remaining three tires. Also, the remaining three tires must be checked in the exact following order, the passenger-side front tire, the passenger-side rear tire and finally the driver-side rear tire. After the final TPMS sensor has re-learned then the horn will beep twice.

5. Listen for the horn to beep twice. When the horn does beep twice, it wikll be the indicator that the TPMS system has re-learned and reset.

6. Turn the ignition switch to the "Off" position, and then be certain that all four tires have the correct tire pressure as recommended on the drivers door, and the next time that the ignition is turned on, the tire pressure light should be reset.

Let me know if you require any further assistance.

Sep 23, 2010 | 2009 Saturn VUE

1 Answer

Change Engine Oil Light stays on


if your vehicle does not have the optional Drive Imformation( DIC) do the followig. 1.with the ignition key ON, but the egine OFF , fully push and release the accelerator pedal 3 times within five seconds. - the Change Engine Oil message should be off - If the Change Engine Oil message comes back on, the engine oil life monitor has not reset, Repeat the procedure. If your vehiclehas the optional ( DIC ), do the following: 1 turn the engine ON, with the engine OFF. 2 press the MODE button until the DIC reads OIL LIFE LELT/ HOLD SET TO RESET 3. press and hold the SET button until 100% is displayed. You will hear 3 chrimes and the Change Engine Oil message will go off. if the Change Oil message comes back on, the system has not reset, Repeat the procedure. Hope this can help , Good luck

Apr 11, 2010 | 2001 Pontiac Aztek

1 Answer

Seat memory


How many buttons are there?
Most times there are three (3) related to the seat positions, with a number 1 on one, and a number 2 on a second. The third button (usually on top of the other two) is an "exit" button (usually) that moves the seat to the full forward position, allowing the rear seat passenger more room to exit.
As far as the memort goes - put the seat in your favorite position - height, forward / back position, etc. Once you are ok with that, press and hold the number 1 or 2 button for approximate 8 seconds. You should hear a beep or tone that indicates the memory has the position in memory. Some Yukon models (i.e. 2004) also require that to commit the seat setting to permanent memory, you have to push the button again (as if you were confirming the setting) and you will hear a similar confirmation tone.

Jun 09, 2009 | 2001 GMC Yukon XL

1 Answer

Oil change


good morning and welcome to fixya.com. do you have an oil change light on that you are trying to reset or do you just want to set the minder on the computer in the overhead console. if its just the overhead console then go to where you want to and hold both buttons in until you hear a beep then the numbers will reset to zero for you along with you fuel mileage and economy gauge. good luck and let me know the outcome.

Mar 07, 2009 | 1996 Jeep Grand Cherokee

4 Answers

How do I program my new Suzuki keyless entry remote to work with our new SUV?


I bought a remote the other day and got these instructions with it. They worked!

1. Make sure vehicle is in Park
2. Press Vehicle Information button (has the icon of a car and an 'i')until 'PRESS *check mark* TO RELEARN REMOTE KEY' displays.
3. Press set/reset button. The message 'REMOTE KEY LEARNING ACTIVE' will display.
4. Press and hold the lock and unlock buttons on the transmitter at the same time for about 15 seconds. A beep will sound indicating that the transmitter is matched.
5. To match additional transmitters at this time, repeat Step 3. Each vehicle can have a maximum of four transmitters matched to it.
6. To exit the program mode, you must cycle the key to LOCK.

Jul 20, 2008 | 2007 Suzuki XL-7

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

362 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

76682 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...