Question about 1994 Toyota Camry
Have 200 toyota camry temp goes high ,fan dont come on but they are good checked may be the themstate is stuck
Posted on Feb 13, 2010
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
1. Look up along the lower radiator hose. It will plug into a metal
tube on the engine side. Follow the metal tube. It goes to a housing.
The housing is kind of buried in the driver's side of the engine. There
are 2 smaller coolant tubes plugged in above it. You do not need to
touch those, although it looks at first glance like you do.
2. Disconnect lower radiator hose at the metal tube.
3. Disconnect fan switches 1 and 2. These are on elecrtical harnesses going to this housing.
4. Disconnect a sensor on the front of the engine, just above the lower hose. I believe this is the knock sensor, but I'm not sure.
5. Now for the fun part. There are 3 bolts holding this housing on. You can see one at the top. There are 2 others underneath it, such that the bolts form a triangle pattern. You will have to get the bottom 2 out by feel (blind). They are 10mm.
6. Also, if you look to the front of the housing, you will note another 10mm bolt on the front holding down a black plastic leg. This is a wiring harness duct. Remove that bolt. Trace back along the duct. There is one more bolt on the driver's side retaining the duct. There is also one on the back of the engine at the firewall / driver's side. Remove these 2 as well.
7. There is a 12mm bolt holding the metal tube from that housing to the driver's side. Remove that bolt.
8. Gently pry the plastic wiring duct toward driver's side, and back toward firewall. You have just enough to get it off of the stud on the thermostat housing.
9. Now you can pull the housing. It will not come all the way out. It will come loose enough to give you just enough clearance to remove the thermostat (barely). Once you remove the thermostat, you have to pass it downward and toward the firewall to fumble it out.
By the way, you will notice that the metal tube is kind of wiggly in the thermostat housiung. This is normal.
10. Pass the new thermostat in the same way you got the old one out. Make sure when you plug it in that it has an air bleed poppet, and that this poppet is facing up.
11. Reassemble by reversing removal. Getting the nuts / bolts back in blind is... fun...
I don't know the torque spec. You can get a torqure wrench in there barely if you get creative with extensions, knuckles, etc. I wouldn't go abouve 8-10 ft-lb.
Posted on May 01, 2009
This is better done when your engine is cold.
Park the car on a level fround.
Open the hood and remove the radiator cap.
Put a sizable container under the radiator and open its drain-plug.
(the drain-plug is by the radiator lower back wall).
Thermostat is in the inlet pipe held by three 10mm bolts that's attached to the engine block. (please note how it sitted)
Installation is reverse of removal. (replace o-ring around thermostat with a new one)
Posted on Nov 13, 2009
its on the driver sidde of the engine. You will see the radiator hose running to the thermostat housing. You must remove the radiator hose and thermostat housing to see it. also make sure your radiator caps seals aren't leaking, especially the one on the top passenger side of the engine!!
Posted on May 10, 2010
Tips for a great answer:
Apr 27, 2012 | 1994 Toyota Camry
Feb 19, 2012 | 1994 Toyota Camry
Dec 28, 2011 | 1994 Toyota Camry
Oct 06, 2011 | 1994 Toyota Camry
Sep 20, 2011 | 1994 Toyota Camry
Jul 24, 2010 | 1994 Toyota Camry
Mar 27, 2010 | 1994 Toyota Camry
Feb 20, 2010 | 1994 Toyota Camry
234 people viewed this question
Usually answered in minutes!