Question about Mitsubishi Passenger

Open Question

How do i change rear brake pads on 4wd gls pajero?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

ghost4548
  • 776 Answers

SOURCE: how to change rear brake pads

Raise the rear of the vehicle and make sure it is securely supported. Remove the rear wheel Remove the brake hose (A) from the suspension arm by removing the brake hose clip (B).Thoroughly clean the outside of the caliper to prevent dust and dirt from entering inside.Support the caliper with a piece of wire so that it does not hang from the brake se.f2d9a24.jpg
Remove the two guide rods (C) and caliper (D) from the bracket. Remove the pad shim (A) and brake pads (B).77fcb0a.jpg

Remove the pad retainers.2884b28.jpg
Clean the caliper thoroughly; remove any rust, and check for grooves and cracks. Check the brake disc for damage and cracks. Install the pad retainers. Check the foreign material at the pad shim (A) and the back of the pads (B). Contaminated brake discs or pads reduce stopping ability. Keep grease off the discs and pads.3fdca95.jpg
Install the brake pads (B) and pad shim (A) on the caliper bracket. Install the inner pad with its wear indicator (C) facing down ward. If you are reusing the pads, always reinstall the brake pads in their original positions to prevent a momentary loss of braking efficiency. Rotate the caliper piston (A) clockwise into the cylinder, the align the cutout (B) in the piston with the tab (C) on the inner pad by turning the piston back. Lubricate the boot with rubber grease to avoid twisting the piston boot. If the piston boot is twisted, back it out so it is positioned properly.1d2811d.jpg
Install the brake caliper (D). Install and torque the guide rods (E) to proper specification. Install the brake hose (F) onto the suspension arm with the brake hose clip (G). After installation, check for leaks at hose and line joints and connections, and retighten if necessary. Depress the brake pedal several times to make sure the brakes work, then test-drive. Engagement of the brake may require a greater pedal stroke immediately after the brake pads have been replaced as a set. Several applications of the brake pedal will restore the normal pedal stroke.

Posted on Jun 02, 2009

samson-1
  • 153 Answers

SOURCE: rear brake cylinders are stuck, can not push them in

I'm not sure about your vehicle but some models must be turned as they go back.

Posted on Oct 27, 2008

  • 651 Answers

SOURCE: CHANGING REAR BRAKE PADS

the best thing you can do is go to an autoparts store and purchase a haynes repair manual for your car. cost about $18, but will show you everything you need to know, with pictures.

Posted on Nov 28, 2008

greg_margo
  • 1959 Answers

SOURCE: Jeep Commander Rear Brake Pad Installation

Per Chilton Auto repair manual:

Removal & Installation

  1. Raise and safely support the vehicle.
  2. Remove the rear wheel.
  3. Siphon a small amount of brake fluid from the master cylinder reservoir.
  4. Insert a small prybar through the caliper opening and pry the caliper cover (using the outboard brake pad) to bottom the piston in the caliper bore.
  5. Remove the caliper slide bolts.
  6. Remove the caliper from the anchor.

    WARNING Support the brake caliper with mechanics wire. Do not let the caliper hang by the brake hose.
  7. Remove the brake pads from the caliper.
To install:
  1. Install the brake pads onto the caliper.
  2. Lubricate the slide pin bolts with grease provided with the brake pads, or suitable silicon grease equivalent.
  3. Install the caliper on the anchor and tighten the slide pin bolts to 18 ft. lbs. (25 Nm).
  4. Install the rear wheel.
  5. Lower the vehicle.
  6. Pump the brake pedal several times until a firm pedal is obtained in order to properly seat the pads.
  7. Refill the brake fluid reservoir to the proper level.

Posted on May 17, 2009

  • 57 Answers

SOURCE: How To Change Rear Brake Pads on Audi A6 2006

Remove the tires, Remove the calaper bolts, (small heads on them 12mm or so) Remove calaper, Pads are setting in a holder. Lube new pads with litheum grease and place in holder. (look at old pads, one or both may have small metel tab on one end) If the new pads have the tab, put that pad where the old pad with the tab was. (ie. tab to the inside) Press pistion in with a 'C' clamp. If it won't go in easly, it may screw in. If the parking brake cable is hooked to the calaper, it probly screws in. Use large pliers to screw in calaper piston. Place calaper over pads and install bolts (lube bolts) Rember to pump brakes befor driving . to get a solid peddle.

Posted on May 20, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What 2h 4h 4hlc 4llc is used for in a pajero


  1. The Mitsubishi Pajero Owners Club® :: View topic - 2H / 4H ... www.pocuk.com/forums/viewtopic.php?t=52960
    • 2 POSTS
    • FIRST POST: 2006-10-07
    2006-10-07 · pajero owners club,pajero,owners,club,pajero club,pajero insurance,insurance,pajero website,car,cars,mitsubishi,yellow diamond,four,4,wheel ... 2H / 4H / 4HLc / 4LLc ...
  2. When do you engage 4h, 4hlc or 4Llc? - Pajero 4WD Club of ... www2.pajeroclub.com.au > ... > Vehicles > Generation 4-2 Pajero
    • 33 POSTS
    When do you engage 4h, 4hlc or 4Llc? Generation 4-2 Pajero User Name: Remember Me? ... with 225 wide tyres got bogged instantly in 4H! I was still in 2H!
  3. Pajero 4WD WHEN WHAT. . . .... - Pajero Owners Club UAE ... https://www.facebook.com/permalink.php?id=435094183183229&story... Pajero 4WD WHEN WHAT. . . . ... Well these seemingly obfuscating things at first ( 2H 4H 4hlc 4LLc ) is what making our PAJERO a TRUE OFF ROADER !!!
  4. Mitsubishi Pajero Sport: The Prodigy Returns - Top Gear www.topgear.com/.../mitsubishi-pajero-sport-the-prodigy-returns/... Mitsubishi Pajero Sport: The Prodigy Returns. ... 2H, 4H, 4HLc and 4LLc. ... But with the Pajero, you can use 4H on paved surfaces thanks to the centre differential, ...
  5. Super Select - Wikipedia, the free encyclopedia https://en.wikipedia.org/wiki/Super_Select The interior of a 2007 Mitsubishi Pajero, with the Super Select gearlever visible to the left of the INVECS transmission lever. Super Select is the ... 4HLc and 4LLc ...
  6. Mitsubishi AWC - Wikipedia, the free encyclopedia https://en.wikipedia.org/wiki/Mitsubishi_AWC According to Mitsubishi, AWC philosophy is put into practice by means of ... (2H, 4H, 4HLc, 4LLc) ... Pajero also features an upgraded version of Mitsubishi's Active ...
  7. Slipping out of 4H and 4HLc - Pajero 4WD Club of Victoria ... www2.pajeroclub.com.au > ... > Vehicles > Generation 3 Pajero
    • 29 POSTS
    Slipping out of 4H and 4HLc Generation 3 Pajero ... Pajero 4WD Club of Victoria Public Forum > Vehicles > Generation 3 Pajero: Slipping out of 4H and 4HLc
  8. Mitsubishi Super Select 4wd and Super Select II www.offroadaussie.com/2013/06/mitsubishi-super-select-4wd The Mitsubishi Super Select 4wd system provides drivers with the ... When changing from 2H to 4H, ... So there is a gear lever that changes between 2h, 4h, 4hlc and 4llc.
  9. Pajero Owners Club of South Africa & 4H to 4HLc ... pajeroclub.co.za/forum/viewtopic.php?t=2318
    • 10 POSTS
    • FIRST POST: 2011-05-11
    2011-08-16 · I know on my 3.5 V6 I can move from 2H to 4H while on the move with ... Only 4HLc to 4LLc requires you to stop and put ... 2003 Mitsubishi Pajero 3.2 DiD ...
  10. HDC ????????????? ?? Mitsubishi Pajero Sport 2015 ... www.youtube.com/watch?v=YKg0Ro8BmU4
    • BY WICHETTT THAMRUNGPITAK
    • 4 MIN
    • 12K VIEWS
    2015-10-21 · ... 2015 ??????? 2H,4H, 4HLc, 4LLc ... Pajero Sport 2015 (4H ... New Pajero Sport 4x4 _Test Drive by ...
  11. Pagination

Mar 04, 2016 | Cars & Trucks

1 Answer

2012 Hyundaii Accent with 30,000 miles. Rear brakes gone,is this possible


Yes especially if you are heavy footed on brakes. Do you coast to a slow then apply or are you waiting till close to required stop point?
Brake pads can be of different grades and wear quickly if of low grade. Are your rotors gone too or just the pads?

Sep 21, 2013 | 2012 Hyundai Accent GLS Sedan 1.6L 4-cyl....

1 Answer

I have a Ford F250 superduty crewcab 4wd. I am going to replace the rear pads. Do I have to set the rear brakes for the emergency brake and how do I do it.


No do not set the E-brake , change them just like you would the front one side at a time. After installing the new pads and the wheels are back on set the E-brake 2 or 3 time and the pump the brake to make sure the calipers have seated.

May 10, 2011 | Ford F-250 Super Duty Cars & Trucks

2 Answers

Are the front and rear brake pads the same or different sizes on my 2003 Silverado 1500 (4wd)?


YOU HAVE TO BUY FRONT PADS FOR FRONT BRAKES AND REAR PADS FOR REAR BRAKES THERE IS SOME DIFFERENCE.

Mar 04, 2011 | 2003 Chevrolet Silverado 1500

1 Answer

Right side rear brake drags


Remove all rust from pad and caliper sliding surfaces,eg metal to metal,not the pins,they get synthetic brake lube. Apply anti-seize to all sliding surfaces. Make sure you can screw in the rear caliper piston,if applicable, and manually ratchet up the parking brake,after caliper and pads are on. Bleed/Flush all 4 Wheels. Make sure you can slide the pads back and forth,before lubing end tabs. You may need to file a little off the ends or just remove the paint. Make sure parking brake cables are really releasing.

Mar 12, 2010 | 2001 Mitsubishi Montero Sport 4WD

1 Answer

I have a 99 isuzu trooper (jackaroo) 3.5 liter 4wd with torque on demand my jssue is the check rear wheel's lights blinks green then red if I put it in 4wd the rear wheel light indicator gose green the...


sounds like a sensor - when did it start - if just cranked up one day and bam it is there - sounds like either a brake wear indicator issue - if they are connected in those - or a fluid level change in the rear end or transfer case - look for leaks and check the brake pads or shoes

Dec 26, 2009 | 1999 Isuzu Trooper

3 Answers

At what mileage should the rear brakes be replaced? Is it common for the rear brakes to be replaced at less than 22,000 miles on a 2007 Sonata gls?


Most of the stopping power goes to the front of the car. You usually go thru two sets or sometimes three sets of front pads before you need to change the rear brakes. It sounds odd the rear brakes need to be replaced at 22,000. havee the front brakes been replaced before?

Sep 17, 2009 | 2007 Hyundai Sonata Limited Sedan

1 Answer

Rear Brake Squeal. 2003 F-150 4Wd


change to a ceramic pad not semi metallic

Jan 28, 2009 | 2003 Ford F150 Regular Cab

2 Answers

Rotors on rear of 2003 jetta gls


Do you really need the Rotors replaced? How many miles? Are they metal on metal when you brake? Can you have them turned at an auto parts suply house? Remove and replace as in solution #1 but explore yor options first.

Oct 20, 2008 | 2003 Volkswagen Jetta TDI

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

930 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75235 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7795 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...