Question about 1988 Chevrolet Blazer

1 Answer

Installed a new manifold now blazer don't get fuel to t.b.i and my headlights don't work

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 377 Answers

Check the fuel hose, may be it is stock thats why the fuel won't go through and regarding the headlights check the connections and if the connections and the wires are ok check the fuse.

Posted on Feb 02, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2000 blazer will not start did a manifold gasket job, replaced plugs, wires, distributor cap,new fuel filter. Cranked and ran really good for 2 days then will not crank


Check you starter, maybe you have a loose connection. Try to give direct power to the starter and see what's happening. I nothing happens, you have a bad starter.

Mar 16, 2013 | 2000 Chevrolet Blazer

1 Answer

How to install headers on a 2001 chevy 4.3


You are wanting to put headers on a Blazer? Power to ya, dude! I doubt if anyone can tell you how to do it other than unbolt the existing manifolds and bolt the headers in....hope they fit...

Have you thought about what you are going to do with the REST of the exhaust system? Like the O2 sensors, catalytic converter, etc.? Install headers because it sounds cool and all your buddies will be impressed with all the "power" it gives your Blazer...only to totally mess up your fuel control and have it run like ****???

I don't get it.....

Good luck

May 11, 2012 | 2000 Chevrolet Blazer

1 Answer

Where is the fuel pressure regulator located on a 1996 Chevy Blazer with a 4.3 V6 engine?


The fuel pressure regulator is under the upper manifold assembly. disconect battery remove manifold release the fuel pressure, remove the fuel pressure regulator snap ring retainer the regulator assembly and the O-rings.

Jan 03, 2011 | 1996 Chevrolet Blazer

1 Answer

If i put a little gas in the carberator and fight with my blazer it will start and stay started, but if i leave it for awhile, it will turn over but not start. i cant figure out if it is electric or...


Get a fuel pressure gauge and connect it to the rail for the fuel injectors to read pressure.

If the pressure is too low, it might be a bad fuel pressure regulator or pump:

Fuel Pressure Regulator Removal & Installation 2.2L Engine To Remove:
  1. Relieve the pressure in the fuel system.
  2. Disconnect the negative battery cable.
  3. Disconnect the vacuum hose from the fuel pressure regulator.
  4. Remove the pressure regulator mounting screw.
  5. Remove the fuel pressure regulator assembly with O-ring. Inspect filter screen for contamination. If contaminated, remove and discard.
Fuel pressure regulator removal/installation (2.2L SFI engine) gm-05-22-619.gif

To Install:
  1. Apply clean engine oil to the new pressure regulator O-ring and install the O-ring on the regulator.
  2. Install the regulator on the fuel rail. Apply thread-locker to the mounting screw.
    • Tighten the screw to 106 lb in (12Nm).
  3. Connect the negative battery cable.
  4. Use the following procedure to pressurize the fuel system and check for leaks;
  5. Turn the ignition ON for 2 seconds.
  6. Turn the ignition OFF for 10 seconds.
  7. Turn the ignition switch back ON to run the fuel pump again and pressurize the fuel system.
  8. Check the fuel rail assembly for fuel leaks.
4.3L Engine RPO L35 To Remove:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold (See: Upper Intake Manifold)
    • Fuel pressure regulator retainer clip (M) and discard the clip
    • Regulator (N) from the housing by twisting and pulling the fuel pressure regulator (N) and using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (R) and discard the O-ring seal
    • Regulator filter (Q) and discard the filter
    • Regulator seal O-ring (P) and discard the O-ring seal
    • Backup ring (O) and discard the ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO L35) Fuel meter body assembly gm_trk_sil15_02-04_43_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (O)
    • Regulator seal O-ring (P)
    • Regulator filter (Q)
    • Regulator seal O-ring (R)
  3. Install or connect the following:
    • Fuel pressure regulator with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (M)
    • Upper manifold
  4. Test drive the vehicle to confirm the repairs
RPO LU3 To Remove:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Before servicing the vehicle, refer to the Cautions and Warnings in the beginning of this section
  2. Remove or disconnect the following:
    • Upper intake manifold
    • Fuel pressure regulator retainer clip (E)
    • Regulator (F) from the housing by twisting and pulling the fuel pressure regulator (F) while using a shop towel to catch any spilled fuel
    • Regulator seal O-ring (J) and discard the O-ring seal
    • Regulator filter (I) and discard the filter
    • Regulator seal O-ring (H) and discard the seal
    • Backup ring (G) and discard the backup ring
  3. Cover the fuel pressure regulator housing to prevent contamination from entering the fuel system
To Install:
4.3L (RPO LU3) Fuel meter body assembly gm_trk_sil15_02-04_43_rpolu3_fuel_metr_body_assy.gif

  1. Lubricate the NEW O-ring seals with clean engine oil.
  2. Assemble the following new parts to the fuel pressure regulator:
    • Backup ring (G)
    • Regulator seal O-ring (H)
    • Regulator filter (I)
    • Regulator seal O-ring (J)
  3. Install or connect the following:
    • Fuel pressure regulator (F) with the vacuum tube pointing down
    • Fuel pressure regulator retainer clip (E)
    • Upper intake manifold
  4. Test drive the vehicle to confirm the repairs
prev.gif next.gif

Nov 04, 2010 | 2002 Chevrolet Blazer

2 Answers

My 2001 chevy blazer (v-6, 4.3L)., has a fuel injector problem and I would like to know how to repair the number 5 injector.


You will need to remove the fuel rail bolted to the intake manifold. There maybe a clip holding on the injector. Spraying some WD-40 on the ends of the injectors to aid removal, also when installing, spray some on the O-rings, will help in installing them. Make sure all are seated.

Mar 08, 2010 | 2001 Chevrolet Blazer

1 Answer

Where is fuel pressure regulatore located


For 2000 Chevrolet Truck Blazer 4WD 4.3L SFI 6cyl
If your engine is a 4.3L V-6 with CPI (central point injection) it is inside the upper intake manifold. The upper intake manifold is bolted on top of the normal intake manifold.

The throttle body is mounted on it and your fuel lines terminate into the center of this.


Removal & Installation
  1. Relieve the fuel system pressure.
  2. Remove the air cleaner outlet resonator.
  3. Disconnect the engine wiring harness from the retaining clips at the front of the engine.
  4. Disconnect the fuel pressure regulator vacuum line.
  5. Clean any dirt from the fuel pressure regulator and the surrounding area.
  6. Disconnect the fuel return pipe.
  7. Remove the fuel return pipe retainer.
  8. Remove the fuel pressure regulator retainer.
  9. Remove the fuel pressure regulator.
  10. Inspect the regulator filter screen for contamination. If contaminated, replace the fuel pressure regulator.
To install:


aaf5240.jpg
Fig. Fuel pressure regulator-4.2L engine
  1. Install the regulator filter.
  2. Install the new O-ring on the fuel pressure regulator.
  3. Lubricate the fuel pressure regulator O-ring with clean engine oil.
  4. Push the fuel pressure regulator into the regulator housing on the fuel rail.
  5. Install the fuel pressure regulator retainer. Tighten the regulator retainer screw to 71 inch lbs. (8 Nm).
  6. Install the fuel return pipe retainer. Tighten the return pipe retainer screw to 71 inch lbs. (8 Nm).
  7. Connect the fuel return pipe.
  8. Connect the fuel pressure regulator vacuum line.
  9. Connect the negative battery cable.
  10. Inspect for leaks:
    1. Turn ON the ignition for 2 seconds.
    2. Turn OFF the ignition for 10 seconds.
    3. Turn ON the ignition.
    4. Inspect for fuel leaks.
  11. Install the engine wiring harness into the retaining clips at the front of the engine.
  12. Install the air intake resonator.
Hope help with this (remember rated this post).

Feb 26, 2010 | 2000 Chevrolet Blazer

1 Answer

1998 blazer will not start


there is a tube system on the vortec under the mainfold the delivers the fuel called the spider and these are known to start leaking on higher mile engines, if there is any fuel in the engine oil you need to fix asap or bearings will get ruined and engine will be needing rebuild.

Aug 16, 2009 | 1998 Chevrolet Blazer

1 Answer

Chevrolet Blazer 1997.


If sender is new in the fuel tank, you have a wire problem between conection of fuel sender and dashboard gauge most likely place at dasbboard gauge.

Nov 27, 2008 | 1997 Chevrolet Blazer

2 Answers

My truck will not start. i have a new starter, alternator, fuel filter fuel pump, mas, air filter. any other suggestions. its fine once its started. i spay choke spray in it to get started.


I have had similar problems and had to replace the fuel pressure regulator. It's a major expense because it sets below the diaphram in the intake manifold. Ask your mechanic about it, it may be the issue. I would get about 30,000 miles between replacement, I've replace it 3 times since purchasing the 2000 chevy blazer new, first one was under warranty.

Jul 25, 2008 | 2000 Chevrolet Blazer

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

28 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8514 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...