Question about 1999 Mercedes-Benz E-Class

Open Question

Removing the headlamp bulb assembly to change bulb Mercedes E220

I turn the bulb assembly anticlockwise and I can then pull it out about 5mm but after that it seems to catch on something inside

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 3 Answers

SOURCE: Removal of Headlamp bulb?

The Xterra doesn't have stock xenon headlights, so are your lights aftermarket? If not, there is a retaining ring on the back of the headlight housing (under the hood) and you just turn the ring counter clockwise to detach and the the bulb comes right out. Installation is the reverse of removal.

Posted on Nov 24, 2008

  • 2 Answers

SOURCE: Change bulb in front headlamp

Yes you do have to remove the bumper, there are 2 screws underneath the assembly which the bumper obstructs. Once you get to this point it is pretty straight forward.

Posted on Jun 26, 2009

  • 119 Answers

SOURCE: 2005 Subaru Impreza Corner Indicator Bulb Replacement

the front bumper cover needs to come away from the headlamp, the book says to remove it entirely but you can usually pull it far enough away to remove lamp on either side, this job is easier than you think, remove grille,then remove fasteners from inside each front wheel well,than the black plastic clips that are on the bottom of the cover need to come off then gently pull forward,i guess if your this far i would replace the bulb on the otherside, why do it twice good luck

Posted on Jul 23, 2009

  • 163 Answers

SOURCE: Replace pass side headlight bulb on Volvo '02 S40

won`t the coolent tube pull out

Posted on Nov 28, 2009

  • 1619 Answers

SOURCE: mercedes e220, horn, heater fan and electric

Horn and heater may be fuse related. The headrests have nothing to do with fuses. The switch is bad or going that way for the seat or the motors for the headrests are out.

The horn fuse spin it, or replace as corrosion from aluminum fuses cause problems. I suggest replacing them all with new copper barrel fuses. The blower motor fan is a strip fuse on the driver side strut mount in a tootsie roll sized case.

Posted on Apr 15, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to change light on front day time lights


Open the hood. Pull up on the retaining pins that hold the headlamp assembly into place.
2 Pull straight up on the headlamp assembly carefully, as all of the bulb wiring will be attached to the rear of the assembly.3 Locate the DRL bulb in the headlamp assembly, which will may be the socket at the inboard position in the assembly.4 Turn the DRL bulb socket in a counterclockwise direction and pull it straight out of the back of the headlamp assembly. (Note: Some vehicles may utilize a release lever that needs to be depressed before the socket can be turned.) 5 Pull the DRL bulb straight out of the socket and discard it. Push a fresh bulb into its place until it is fully seated.6 Push the socket back into the rear of the headlamp assembly and turn it in a clockwise direction until it locks into place.7 Place the headlamp assembly back into position on the front of the vehicle. Push the retaining pins back down until they lock into place.

Sep 29, 2011 | 2003 Buick Regal

1 Answer

I need to change the headlights


REMOVAL PROCEDURE
  1. Open the hood.
  2. Remove the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly to flex forward.
  3. Remove the bolt and the push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.

  1. Gently pull the upper fascia and grille assembly forward only far enough to remove the bolt located at the bottom inboard side of the headlamp assembly.
  2. Pull the headlamp assembly straight out to disengage the snap-in retainer at the lower outboard back surface of the assembly. Turn the assembly so that the front inboard corner clears the front fascia.
  3. Pull the headlamp assembly out and away from the vehicle
  4. Disconnect the headlamp electrical connector.
  5. Remove the headlamp assembly from the vehicle.
  6. Remove the headlamp bulb cover from the headlamp assembly.
  7. Remove the headlamp bulb socket from the headlamp assembly.
CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Remove the headlamp bulb.
  2. Remove the side marker bulb socket from the outer side of the headlamp assembly.
  3. Remove the side marker bulb.
  4. Remove the parking lamp bulb socket from the inner edge of the headlamp assembly.
  5. Remove the parking lamp bulb.
INSTALLATION PROCEDURE

CAUTION: Refer to Halogen Bulb Caution in Service Precautions.


  1. Install the headlamp bulb to the socket.
  2. Install the headlamp bulb socket to the headlamp assembly.
  3. Install the headlamp bulb cover to the headlamp assembly.
  4. Install the side marker bulb to the socket.
  5. Install the side marker bulb socket to the headlamp assembly.
  6. Install the parking lamp bulb to the socket.
  7. Install the parking lamp socket to the headlamp assembly.
  8. Connect the headlamp electrical connector.
  9. Install the headlamp assembly to the vehicle by placing it back into position so that the bolt holes align and the snap-in retainer located at the outboard back surface of the headlamp assembly engages.
  10. Gently pull the upper fascia and grille assembly forward only far enough to install the bolt located at the bottom inboard side of the headlamp assembly.
NOTE: Refer to Fastener Notice in Service Precautions.
  1. Install the bolt and push-pin retainer that secures the top of the headlamp assembly to the upper tie bar.
Tighten the bolts to 6 N.m (53 lb in).


  1. Install the push-pin retainers that secure the top of the upper fascia and grille assembly to the upper tie bar to allow the upper fascia and grille assembly.
  2. Close the hood.
3e4ca4a.gif

Oct 21, 2010 | 2006 Cadillac SRX

1 Answer

How to change headlight fo 2005 chevrolet uplander


Headlamp Removal & Installation Bulb Replacement To Remove:
  1. Remove the Headlamp Assembly. Headlamp bulbs gm-06-00-3206.gif

  2. Turn the high/low beam bulb socket counterclockwise to remove.
To Install:
  1. Turn the high/low beam bulb socket clockwise to install.
  2. Install the Headlamp Assembly.
Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I gm-06-00-3207.gif

  1. Rotate the headlamp assembly retainer pins and pull up to remove.
  2. Remove the mounting bolts.
  3. Disconnect the harness connectors.
To Install:
  1. Connect the harness connectors.
  2. Position the headlamp assembly on the panel.
  3. Rotate the retainer pins and push down to lock in place.
  4. Install and secure the mounting bolts.
prev.gif next.gif

Oct 07, 2010 | 2005 Chevrolet Uplander

1 Answer

How to change front turn light bulb


At the back of the headlamp, pull two retainer pins up to release the
headlamp assembly.
Pull headlamp assembly forward disengaging the lamp from the rear
retainer to expose the back of the bulb.
Remove bulb socket by turning it counterclockwise, then slide it out
of the lamp assembly.
Carefully pull bulb straight out of the socket and push in the new
bulb.
To complete installation, follow removal procedure in the reverse
order.

Sep 06, 2010 | 2000 Ford Windstar

1 Answer

How do you change the headlight on a 2006 grand prix


  1. Raise the hood.
  2. Lift upward on the headlamp retainer (1).
  3. Pull the headlamp assembly outward enough to release the headlamp assembly from the upper fascia support.
  4. Position the headlamp assembly away from the vehicle body to access the electrical connector
    1. Disconnect the electrical connector from the headlamp assembly.
    2. Remove the headlamp assembly from the vehicle.
    3. Use caution handling halogen bulbs. Remove the headlamp bulb/socket from the headlamp, by turning counterclockwise. CAUTION: Refer to Halogen Bulb Caution in Service Precautions.
    4. Remove the headlamp bulb/socket from the headlamp assembly.450a6d8.gif

May 06, 2010 | 2006 Pontiac Grand Prix

1 Answer

HOW TO CHANGE HEADLIGHT


  1. Open the hood.
  2. Remove push-pin fasteners from the grill assembly.
  3. Tilt the grill assembly forward and lift it up to remove it from the vehicle.
  4. Remove the fasteners from the headlamp assembly.
  5. Push the headlamp housing lever up to disengage the headlamp housing from the headlamp housing pocket.
  6. Turn the bulb socket being replaced counterclockwise one-quarter of a turn while pressing the socket in firmly.
  7. Pull the socket rearward until the bulb clears the headlamp housing, and lift it up to access the bulb.
  8. Disconnect the wire connector from the bulb by lifting the lock tab and pulling it away from the plastic base.
  9. Remove the bulb assembly and replace it with the appropriate bulb.
  10. Reverse the steps to reinstall the headlamp assembly.

May 05, 2010 | 2003 Saturn L-Series

1 Answer

Change headlinght bulb


SECTION 417-01: Exterior Lighting 2005 Freestyle/Five Hundred/Montego Workshop Manual REMOVAL AND INSTALLATION Procedure revision date: 03/14/2005 Headlamp Bulb adobe.gif Printable View (327 KB) Freestyle, Five Hundredn0035265.gif
Item Part Number Description 1 — Headlamp bulb electrical connector (part of 14290) 2 13N021 Headlamp bulb

Montegon0035266.gif
Item Part Number Description 1 — Headlamp bulb access cover screws (6 required) (part of 13006) 2 13N019 Headlamp bulb access cover 3 — Spring retainer (part of 13006) 4 13N021 High intensity discharge (HID) bulb 5 14A411 HID bulb electrical harness 6 — High beam bulb electrical connector (part of 13006) 7 13N021 High beam bulb Removal and Installation
ani_caut.gif WARNING: The headlamp bulb contains gas under pressure. The bulb may shatter if the glass envelope is scratched or if the bulb is dropped. Handle the bulb only by its base. Avoid touching the glass envelope. Failure to follow these instructions may result in personal injury.
NOTE: The headlamp bulb should not be removed from the headlamp assembly until just before a new bulb is installed. Removing the bulb for an extended period of time may affect headlamp bulb performance. Contaminants may enter the headlamp assembly where they can settle on the lens and reflector. Never turn on the headlamps with the bulb removed from the headlamp assembly.
NOTE: Make sure the headlamp switch and ignition switch are in the OFF position.
Freestyle, Five Hundred
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego
  1. Remove the headlamp assembly. For additional information, refer to Headlamp Assembly — Five Hundred, Montego in this section.
  1. Remove the 6 screws and the headlamp bulb access cover.
Montego high beam bulb
  1. Rotate the headlamp bulb 1/8-turn counterclockwise and remove the headlamp bulb.
    • Disconnect the electrical connector.
Montego HID bulb
  1. Release the spring retainer and remove the HID bulb.
    • Disconnect the electrical connector.
All vehicles
  1. To install, reverse the removal procedure.

2010&c18=modelyear&c20=n920901&c35=wsm%2cheadlamp%20bulb%2cs5f%2c417-01%2cremoval%20and%20installation&s=1600x900&c=32&j=1.3&v=y&k=y&bw=1171&bh=582&ct=lan&hp=n&[aqe]

Apr 02, 2010 | 2005 Ford Five Hundred

1 Answer

Headlights removal ford explorer 96


  1. Check that headlamp switch (11654) is in the off position.
  2. Lift hood (16612).
  3. Release latch and swing filler panel to left or right.
  4. Remove electrical connector from headlamp bulb by grasping wires firmly and snapping connector rearward.
  5. Remove headlamp bulb retainer (13N019) by rotating counterclockwise (when viewed from rear) about one-eighth turn and sliding ring off plastic base. Keep headlamp bulb retainer as it may be used again to retain new headlamp bulb.
  6. Carefully remove headlamp bulb from socket by gently pulling straight backward out of socket. Do not rotate headlamp bulb during removal. 7056091.gif
Headlamp Assembly, Explorer
Removal and Installation
  1. Disconnect battery negative cable.
  2. Remove blind rivets (2) attaching screws (4) and radiator upper sight shield.
  3. Remove turn/park lamp attaching screws (2) and pull assembly away from body. Remove bulb sockets from housing and remove lamp assembly. Repeat on opposite side of vehicle.
  4. With turn/park lamp assembly removed, screw attaching grille to front fender flange is accessible. Remove grille attaching screw. Repeat on opposite side of vehicle.
  5. Remove attaching screws (4) located across top of grille.
  6. Grip lower edge of grille and pull outward to disengage from retaining clips. Remove grille.
  7. Using needle-nose pliers, compress barbs on headlamp housing retainer. With barbs compressed, pull forward on housing just enough to disengage from retainer. Repeat on opposite side of headlamp housing.
  8. Turn headlamp housing as necessary and pull forward to disengage from headlamp aiming ball socket.
  9. Disconnect wiring from headlamp bulb socket.
  10. If replacing headlamp housing, remove retaining collar and bulb.
For installation, follow removal procedures in reverse order. Make sure to check headlamp aim. 568a220.gif

Apr 02, 2010 | 1996 Ford Explorer

1 Answer

How do i change right turn lamp in my 2004 pontiac grand prix


Answer remove the headlight assembly and the bulbs are located below the Assembly to remove headlamp assembly and access signals: -open the hood
-while pushing rearward on the headlamp,pull up half-way on the (white)plastic retaining clip on the electrical connector - align the square cut-out on the retaining clip with the notch on the headlamp
-pull the headlamp assembly straight out from the vehicle (moving the headlamp up and down slightly may help with its removal)
-locate the front turn signal,parking lamp and foglamp bulbs which are located below the headlamp assembly (turn/parking lamp on top and the fog lamp is below it)
-turn the bulb socket 1/4 turn counterclockwise to remove it from assembly
-pull the old bulb from the socket and replace it with a new one
-turn the bulb socket a 1/4 turn clockwise to reinstall it
-reinstall the headlamp assembly carefully so you dont scratch the paint
-push down on (white)plastic retaining clip on the electrical connector while pushing rearward on the headlamp making sure headlamp is secure.

Nov 26, 2009 | 2004 Pontiac Grand Prix

3 Answers

Change low beam


Headlamp Removal & Installation Bulb Replacement To Remove:
CAUTION
Halogen bulbs contain pressurized gas. Mishandling a bulb may result in the bulb shattering into flying glass fragments.
CAUTION
Make sure to wear eye protection when handling a halogen bulb.
CAUTION
Do not touch the glass of a halogen bulb, only handle the bulb by the base.
CAUTION
Do not allow a halogen bulb to come into contact with dirt or moisture.
CAUTION
Make sure to dispose of a used halogen bulb properly.
CAUTION
Do not allow children to handle halogen bulbs.
  1. Turn the lamp switch to the off position.
  2. Make sure the bulb is cool before changing.
  3. Remove the headlamp assembly from the headlamp panel.
  4. Remove the rear access cover from the headlamp assembly.
  5. Disconnect the headlamp connector.
  6. Remove the bulb from the headlamp assembly by rotating the bulb and socket counterclockwise.
To Install:
  1. Connect the headlamp connector.
  2. Install the bulb into the headlamp assembly by rotating the bulb and socket clockwise.
  3. Install the rear access cover onto the headlamp assembly.
  4. Install the headlamp assembly into the headlamp panel.

Jul 16, 2009 | 2004 Chevrolet TrailBlazer

Not finding what you are looking for?
1999 Mercedes-Benz E-Class Logo

Related Topics:

483 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mercedes-Benz Experts

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

yadayada
yadayada

Level 3 Expert

75051 Answers

Michael Contreras
Michael Contreras

Level 2 Expert

166 Answers

Are you a Mercedes-Benz Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...