Question about Honda del Sol

1 Answer

Timing belt specification.

There is a series of marks, 3 in a row, the center one is red, going clockwise there are 2 other marks. To set the timing belt which marks determine top dead center on a 1993 honda del Sol 1.6 liter 16V engine? And what would cause the engine to have no spark after installing the timing belt.

Posted by on

  • funnyfarm5 Feb 08, 2010

    old belt was off, water pump went out while it was being driven and threw timing belt.

  • Bill May 11, 2010

    are you sure nothing moved when you swaped the old belt for the new one.

×

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 23 Answers

The 1.6l is an interference engine and if the timing belt let loose there is a good chance the pistons met the valves and bent them. I'm thinking that you have a compresson problem either caused by bent valves or having the camshaft out of time with the crank.this link seems to be the best description of where the marks need to be I hope it helps http://honda-tech.com/showthread.php?t=1042236&highlight=d16z6+timing+marks+

Posted on Feb 08, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How do i set the timing belt on a 1997 cadillac catera?the betl did not break but how do i make sure the belt did not move a couple of teeth.


Hi, there should be marks on the belt itslf that align with hatch marks on the timing gears. Below are the instructions for installation. From these, you should be able to verify that the belt is in time. There are also some diagrams here: http://www.2carpros.com/diagrams/cadillac/catera/1997


To install:
  1. Install the timing belt.
    1. Start at the crankshaft pulley.
    2. Install the timing belt with a double dash (TDC) mark on the belt aligned with the marks on the oil pump and belt drive gear.
    3. Pinch the belt with special tool J 42069-30 to prevent the splines from jumping.

  2. Route the timing belt through the idler pulley for camshafts 3 & 4 then route the timing belt through the camshaft gears 3 & 4.
    1. Ensure the dash marks on the timing belt align with marks on the camshaft gears and the notches on the rear timing belt cover.
    2. If necessary, loosen timing belt idler pulley or move the cam gears slightly, with J 42069-1 and 2 still in place, until the timing belt can be installed.
    3. Tighten the idler pulley locking bolt until snug. The idler pulley bolt will be tightened to specifications after the final adjustments are made.




NOTE Timing belt deflection between the camshaft gears number 4 and the idler pulley for camshafts 3 & 4, must be no more than 0.4 inch (1 CM.).

  1. If necessary, adjust the timing belt deflection by turning the timing bolt idler pulley eccentric, for camshafts 3 & 4, counter-clockwise with the special tool J 42069-40, or equivalent.

  1. Route the timing belt through the timing belt idler pulley for camshafts 1 & 2 then route the timing belt through camshaft gears 1 & 2.
    1. Ensure the dash marks on the timing belt align with the marks on the camshaft gears and the notches on the rear timing belt cover.
    2. If necessary, loosen the timing belt idler pulley or move the cam gear slightly, with J 42069-1 and 2 still in place, until the timing belt can be installed.
    3. Apply sufficient tension to the timing belt to prevent it from slipping off the gears by turning the timing belt idler pulley eccentric for camshafts 1 & 2 counter-clockwise with special tool J 42069-40 or equivalent.
    4. Tighten the idler pulley locking bolt until snug. Idler pulley bolt will be tightened to specifications after final adjustments are made.

  2. Route the timing belt through the timing belt tensioner.
  3. Apply initial tension to the timing belt by turning tensioner eccentric counter-clockwise, with a 5 mm hex wrench, until marks are set.
    1. Tighten the belt tensioner-locking nut to 15 ft. lbs. (20 Nm).

  4. Adjust the timing belt.
    1. The timing belt must be properly adjusted or engine damage may occur. Do not continue with the engine assembly procedure until the timing belt is properly adjusted.

  5. Install the timing belt cover. Tighten the timing belt cover bolts to 71 inch lbs. (8 Nm).
  6. Install the power steering pump pulley and bolts. Install the water pump pulley and bolts.
    1. Tighten the power steering pump pulley bolts and the water pump pulley bolts after the serpentine drive belt is installed.

Mar 04, 2011 | 1997 Cadillac Catera

1 Answer

WHAT IS CORRECT TIMING MARKS FOR TIMING BELT INSTALLATION. 2000 NUBIRA 2.0 DOHC AND CRNKSHAFT MARKS. Thanks Joe


TIMING BELT
Removal
Disconnect negative battery cable. Disconnect intake air temperature sensor connector from intake air duct. Disconnect the air intake tube from the throttle body. Disconnect the breather tube from the valve cover. Remove resonator from throttle body. Remove air filter housing.
Raise and support the vehicle. Remove right front wheel. Remove right front splash shield from wheelwell. Remove serpentine accessory drive belt.
Remove crankshaft pulley bolts. It is NOT necessary to remove crankshaft sprocket center bolt. Remove crankshaft pulley. Lower vehicle.
Support engine assembly from above with Support Fixture (J-28467-B). Remove engine mount bracket from timing belt end of engine.Remove power steering hose clamp bolt, and position hose away from timing belt cover. Remove front timing belt cover. Using crankshaft center bolt, rotate crankshaft one full turn clockwise (as viewed from timing belt end of engine).
Align mark on crankshaft sprocket with notch at bottom of rear timing belt cover. See Fig. 4 . Align camshaft sprocket timing marks with notches on valve cover. See Fig. 5 .
CAUTION: Engine damage could result if camshaft sprockets are not properly aligned with notches on valve cover.
Loosen the automatic tensioner bolt. Use an Allen wrench to rotate tensioner and relieve tension on timing belt. Remove timing belt.
Fig. 4: Aligning Crankshaft Sprocket Timing Mark
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim_4.jpg
Fig. 5: Aligning Camshaft Sprocket Timing Marks
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim2_3.jpg
Installation
Ensure crankshaft and camshaft timing marks are still aligned. Install the timing belt. See Fig. 7 . Turn the timing belt tensioner counterclockwise to tension the timing belt. Turn tensioner until the pointer aligns with the notch on the rear timing belt cover. Tighten automatic tensioner bolt to specification. See TORQUE SPECIFICATIONS .
Using crankshaft center bolt, turn crankshaft clockwise (as viewed from timing belt end of engine) 2 full revolutions. Ensure timing belt tensioner pointer is still aligned with notch.
If timing belt tensioner is correctly aligned, install timing belt cover. See Fig. 3 . Install the engine mount bracket on the timing belt end of engine. Position power steering hose in place, and install clamp bolt. Install crankshaft pulley. Install serpentine accessory drive belt.
Install right front splash shield. Install right front wheel. Install air filter housing and resonator. Connect air intake temperature sensor connector. Connect negative battery cable.
Fig. 7: Identifying Timing Belt Routing
Courtesy of DAEWOO MOTOR AMERICA, INC.
266999_tim3_1.jpg
here

http://www.2carpros.com/questions/daewoo-leganza-2000-daewoo-leganza-timing-marks

Feb 17, 2011 | 2000 Daewoo Nubira

1 Answer

Como poner la banda de tienpo de un toyota camery


Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence.

Dec 23, 2010 | 1993 Toyota Camry V6

1 Answer

LH guide is straight RHguide is curved has 3=8 slot on top to adjust has springloaded =hydralicassistfd tensioner below RH there is no adjusting screw and you cant get to anything whenfront cover is...


To install:

CAUTION Before installing the timing belt, confirm that the No. 1 cylinder is set at the TDC of the compression stroke.
  1. Remove both cylinder head covers and loosen all rocker arm shaft retaining bolts.
The rocker arm shaft bolts MUST be loosened so that the correct belt tension can be obtained.
  1. Install the tensioner and the return spring. Using a hexagon wrench, turn the tensioner clockwise and temporarily tighten the lock-nut.
  2. Make sure that the timing belt is clean and free from oil or water.
When installing the timing belt align the white lines on the belt with the punchmarks on the camshaft and crankshaft sprockets. Have the arrow on the timing belt pointing toward the front belt covers.

A good way (although rather tedious!) to check for proper timing belt installation is to count the number of belt teeth between the timing marks. There are 133 teeth on the belt; there should be 40 teeth between the timing marks on the left and right side camshaft sprockets, and 43 teeth between the timing marks on the left side camshaft sprocket and the crankshaft sprocket.

  1. 1986-87 Engines:
    1. Using a hexagon wrench, loosen the tensioner lock bolt, set the tensioner and then slowly turn the tensioner clockwise and counterclockwise 2-3 times.If the coarse tensioner stud has been removed, be sure to apply locking sealer to the threads before installing it.
    2. Tighten the tensioner lock-nut to 32-43 ft. lbs. (43-58 Nm). Tighten the rocker arm shaft retaining bolts (in 2-3 stages) to 13-16 ft. lbs. (18-22 Nm).Before tightening, be sure to set the camshaft lobe at the position where the lobe is not lifted.
    3. Install the upper and lower timing belt covers.

  2. 1988 Engines:
    1. While keeping the tensioner steady, loosen the lock-nut with a hexagon wrench.
    2. Turn the tension approximately 70-80 degrees clockwise with the wrench and then tighten the lock-nut.
    3. Turn the crankshaft in a clockwise direction several times and then slowly set the No. 1 piston to TDC of the compression stroke.
    4. Apply 22 lbs. of pressure (push it in!) to the center span of the timing belt between the right side camshaft sprocket and the tensioner pulley and then loosen the tensioner lock-nut.
    5. Using a 0.0138 in. (0.35mm) feeler gauge (the actual width of the blade must be 1 / 2 in. thick!) positioned as shown in the illustration, turn the crankshaft clockwise ( slowly! ). The timing belt should move approximately 2 1 / 2 teeth. Tighten the tensioner lock-nut, turn the crankshaft slightly and remove the feeler gauge.
    6. Slowly rotate the crankshaft clockwise several more times and then set the No. 1 piston to TDC of the compression stroke.
    7. Install the upper and lower timing belt covers.

87fa416.gif

Sep 18, 2010 | 1988 Nissan King Cab

2 Answers

2004 kia rio timing belt replacement procedure


from autozone.com

Removal & Installation

1.5L, 1.6L (VIN 5) & 1.8L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Disconnect the negative battery cable.
  3. Remove the accessory drive belts.
  4. Remove the alternator.
  5. Remove the water pump and crankshaft pulleys.
  6. Remove the timing belt guide plate.
  7. Remove the upper and lower timing belt covers.
  8. Position the crankshaft so that the timing mark is aligned with the timing mark on the engine.
  9. Verify that the I and E mark on the camshaft pulley align with the mark on the cylinder head.
    NOTE Do not move the crankshaft or camshaft once the timing marks have been correctly positioned.
  10. If the timing belt is to be reused, mark the direction of rotation on the timing belt.
  11. Remove the timing belt tensioner pulley.
  12. Remove the timing belt.

25f366d.jpg

b46eac9.jpg

503792b.jpg
To install:
  1. Install the timing belt tensioner pulley, move the tensioner to its furthest point and tighten the lockbolt.
  2. Install the timing belt onto the pulleys, as follows, crankshaft pulley first, then the idler pulley, exhaust camshaft pulley, intake camshaft pulley, and the tensioner pulley.
  3. Loosen the tensioner pulley and allow the tensioner spring to apply tension on the belt, then tighten the lockbolt to 28-38 ft. lbs. (38-51 Nm).
  4. Rotate the crankshaft clockwise 2 turns and be sure all marks are still correctly aligned.
  5. Install the remaining components in the revere order of the removal noting the following torque specifications:

    Crankshaft pulley: 9-13 ft. lbs. (12-17 Nm) Water pump pulley: 9-13 ft. lbs. (12-17 Nm)
  6. Connect the negative battery cable.

1.6L (VIN 3) & 2.0L Engines
  1. Before servicing the vehicle, refer to the Precautions Section.
  2. Remove or disconnect the following:

    Negative battery cable Engine cover Right-hand front wheel Right-hand wheel well side cover Accessory drive belts Water pump pulley Timing belt upper cover
  3. Turn the crankshaft pulley so cylinder No. 1 is at Top Dead Center (TDC). Align the pulley groove with the timing mark T of the timing belt cover.
  4. Remove or disconnect the following:
    NOTE If the timing belt is to be reused, mark the belt to indicate its turning direction.


    Crankshaft pulley Crankshaft flange Lower timing belt cover Timing belt tensioner Timing belt

To install:
  1. Align the timing marks of the camshaft and crankshaft sprockets to ensure the No. 1 cylinder is at TDC.
  2. Temporarily install the timing belt tensioner.
  3. Install the timing belt over the crankshaft sprocket, then inside the idler pulley, over the camshaft sprocket and then inside the timing belt tensioner.
  4. Apply tension to the timing belt by turning the tensioner in the clockwise direction so there is no slack in the belt on the tension side.
  5. Tighten the tensioner mounting bolts to 20 ft. lbs. (27 Nm).
  6. Check the timing belt tension as follows:
    1. 1.6L (VIN 3) engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end is approximately 1 / 2 of the tensioner mounting bolt head radius away from the bolt head center.
    2. 2.0L engine: Push the tension side of the belt in horizontally with a moderate force, the timing belt cog end sags approximately 0.16-0.24 inches (4-6 mm).

  7. Turn the crankshaft two turns in the clockwise direction and realign the crankshaft sprocket and camshaft sprocket timing marks.
  8. Install or connect the following:

    Lower timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Crankshaft flange Crankshaft pulley. Tighten bolt to 101-109 ft. lbs. (138-147 Nm) for 1.6L (VIN 3) engine and 123-130 ft. lbs. (168-177 Nm) for 2.0L engine. Upper timing belt cover. Tighten bolts to 6-7 ft. lbs. (8-10 Nm). Water pump pulley Accessory drive belts Right-hand wheel well side cover Right-hand front wheel Engine cover Negative battery cable

Sep 06, 2010 | 2004 Kia Rio

1 Answer

How do set the timing on hyundai excel 1998


Hi,


It seems you are encountering problems trying to set the timing marks in your elantra,not to worry,simply follow the stepwise solution below;
Ensure timing marks aligned [6] & [7] .

STEP 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets.

STEP 2. Slacken tensioner pulley bolt [8].Push tensioner pulley firmly against timing belt to tension belt.



STEP 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm.


STEP 4. Except Matrix: Turn crankshaft one turn clockwise.



STEP 5. Matrix: Turn crankshaft two turns clockwise.


STEP 6. Ensure timing marks aligned [6] .


STEP 7. Apply a load of 2 kg to belt at .Belt should deflect 4-6 mm. If not Adjust position of tensioner pulley.



STEP 8. Install components in reverse order of removal.


STEP 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm
(7) is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head (6) is crank timing mark,pin mark on crank lines up with markS on block.





Good luck.

Aug 20, 2010 | Hyundai Excel Cars & Trucks

2 Answers

Looking for timing mark's for a 1997 camry with a 2.2 4cyl motor?


Hi,


You find the timing marks on the picture below.

moz-screenshot-2.pngaab8238.jpg



Removal
Remove auxiliary 1. drive belts.
2. Support engine.
Remove:
Engine mounting and bracket.
Timing belt upper cover [1].
3.
4. Turn crankshaft clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Remove:
Crankshaft pulley bolt [4].
Crankshaft pulley [5]. Use tool No.09213-60017.
5.
6. Ensure timing marks aligned [2] & [3].
7. Slacken tensioner bolt [6]. Move tensioner away from belt and lightly tighten bolt.
Remove:
Timing belt lower cover [7].
Crankshaft sprocket guide washer [9].
Timing belt.
Tensioner pulley.

Installation
Installation
1. Check tensioner pulley for smooth operation.
2. Check free length of tensioner spring is 46,0 mm [8]. Replace spring if necessary.
3. Fit tensioner and spring. Ensure spring is connected correctly.
4. tighten bolt [6].
5. Ensure timing marks aligned [2] & [3].
6. Fit timing belt. Ensure belt is taut between sprockets.
Install:
Crankshaft sprocket guide washer [9].
Timing belt lower cover [7].
Crankshaft pulley [5].
7.
8. Slacken tensioner bolt 1/2 turn [6].
9. Turn crankshaft two turns clockwise to TDC on No.1 cylinder. Ensure timing marks aligned [2] & [3].
Turn crankshaft slowly 1 7/8 turns clockwise until crankshaft pulley timing mark [3] aligned with 45° BTDC mark [10] on
timing belt lower cover [7].
10.
11. Tighten tensioner bolt [6]. Tightening torque: 42 Nm.
12. Install components in reverse order of removal.
13. Tighten crankshaft pulley bolt [4]. Tightening torque: 108 Nm.
Manufacturer: Toyota

Jun 25, 2010 | 1997 Toyota Camry

1 Answer

Timing marks setting Hyundai Lantra


Installation
Ensure timing marks aligned [6] & [7] . 1. Fit timing belt in anti-clockwise direction, starting at crankshaft sprocket. Ensure belt is taut between sprockets. 2. Slacken tensioner pulley bolt [8] . Push tensioner pulley firmly against timing belt to tension belt. 3. Tighten tensioner pulley bolt [8] . Tightening torque: 43-55 Nm. 4. Except Matrix: Turn crankshaft one turn clockwise. 5. Matrix: Turn crankshaft two turns clockwise. 6. Ensure timing marks aligned [6] . 7. Apply a load of 2 kg to belt at . Belt should deflect 4-6 mm. If not: Adjust position of tensioner pulley. 8. Install components in reverse order of removal. 9. Tighten crankshaft pulley bolt [2] . Tightening torque: 170-180 Nm

7 is timing mark on cam,pin mark to top,hole in spoke below pin mark lines up with mark on head
6 is crank timing mark,pin mark on crank lines up with mark on block
NOTE this mark is just before top


Mar 21, 2010 | Hyundai Motor 1996 Elantra

1 Answer

Timing for tropper 6cly and 4 camshafts and 24 valves model 2000


Timing Belt
Removal
1. Disconnect battery ground cable.
2. Remove air cleaner assembly.
3. Remove radiator upper fan shroud from radiator.
4. Move drive belt tensioner to loose side using wrench
then remove drive belt.
850RW001
Legend
(1) Crankshaft Pulley
(2) Cooling Fan Pulley
(3) Tensioner
(4) Generator
(5) Air Conditioner Compressor
(6) Power Steering Oil Pump
(7) Drive Belt
5. Remove cooling fan assembly four nuts, then the
cooling fan assembly.
6. Remove cooling fan drive pulley assembly.
7. Remove idle pulley assembly.
8. Remove serpentine belt tensioner assembly.
9. Remove power steering pump assembly.
10.Remove crankshaft pulley assembly using
5–8840–0133–0 crankshaft holder, hold crankshaft
pulley remove center bolt, then the pulley.
11. Remove right side timing belt cover then left side
timing belt cover.
12. Remove lower timing belt cover
13. Remove pusher.
CAUTION: The pusher prevents air from entering
the oil chamber. Its rod must always be facing
upward.
014RW011
Legend
(1) Up Side
(2) Down Side
(3) Direction For Installation
(4) Locking Pin
14. Remove timing belt.
CAUTION:
1. Do not bend or twist the belt, otherwise its core
could be damaged. The belt should not be bent at
a radius less than 30 mm.
2. Do not allow oil or other chemical substances to
come in contact with the belt. They will shorten
the life.
3. Do not attempt to pry or stretch the belt with a
screw driver or any other tool during installation.
4. Store timing belt in a cool and dark place. Never
expose the belt direct sunlight or heat.
6A–30 ENGINE MECHANICAL
Installation
NOTE: For correct belt installation, the letter on the belt
must be able to be read as viewed from the front of the
vehicle.
014RY00042
Legend
(1) Crankshaft Timing Pulley
(2) RH Bank Camshaft Drive Gear Pulley
(3) Water Pump Pulley
(4) Idle Pulley
(5) LH Bank Camshaft Drive Gear Pulley
(6) Tension Pulley
014RY00043
Legend
(7) Alignment Mark on Oil Pump.
(8) Alignment Mark on Timing Belt
(9) Alignment Mark (notch) on Crankshaft Timing
Pulley.
(10) Alignment Mark (groove) on Crankshaft Timing
Pulley.
014RW006
Legend
(1) Timing Belt
(2) Engine Rotation Direction
(3) Cylinder Head Side
1. Install timing belt.
1. Align the mark (notch) of crankshaft timing pulley
(2) with mark on oil pump (1).
Align the mark (groove) on the crankshaft timing
pulley (3) with alignment mark (white dots line) on
the timing belt (4).
NOTE: When timing marks are aligned, No.2 piston will
be on Top Dead Center.
014RW003
Legend
(1) Alignment Mark on Oil Pump
(2) Groove on Crankshaft Timing Pulley
(3) Alignment Mark on Crankshaft Timing Pulley
(4) Alignment Mark on Timing Belt
ENGINE MECHANICAL 6A–31
2. Align the alignment mark on the RH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover RH (3).
3. Align the alignment mark (white line) on the timing
belt (1) with alignment mark on the RH bank
camshaft drive gear pulley (2) (on the left side as
viewed from the front of the vehicle) and put the
timing belt on the camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
014RW00004
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover RH.
4. Align the alignment mark on the LH bank
camshaft drive gear pulley (2) to the alignment
mark of the cylinder head cover LH (3).
5. Align the alignment mark (white line) on the timing
belt (1) with the alignment mark on the LH bank
camshaft drive gear pulley (2).
When aligning the timing marks, use a wrench to
turn the camshaft drive gear pulley, then set the
timing mark between timing belt and camshaft
drive gear pulley and put the timing belt on the
camshaft drive gear pulley.
Secure the belt with a double clip or equivalent
clip.
NOTE: It is recommended for easy installation that the
belt be secured with a double clip or equivalent clip after
it is installed the timing belt to each pulley.
014RW00005
Legend
(1) Alignment Mark on Timing Belt (White line).
(2) Alignment Mark on Camshaft Drive Gear
Pulley.
(3) Alignemnt Mark on Cylinder Head Cover LH.
6. Install crankshaft pulley temporarily and tighten
center bolt by hand (do not use a wrench).
Turn the crankshaft pulley clockwise to give some
belt slack between the crankshaft timing pulley
and the RH bank camshaft drive gear pulley.
2. Install pusher and tighten bolt to the specified torque.
Torque : 25 N·m (2.5 Kg·m/18 lb ft)
1. Install the pusher while pushing the tension pulley
to the belt.
2. Pull out pin from the pusher.
NOTE: When reusing the pusher, press the pusher with
approximately 100Kg to retract the rod, and insert a pin
(1.4 mm piano wire).
014RW011

Mar 18, 2009 | 2000 Isuzu Trooper

2 Answers

Need instructions to replace 1993 Toyota Camry Timing Belt


Hi Kmcarroll77

TIMING BELT REPLACEMENT - 2.2L -1993 Toyota Camry

Installation
1.Install No. 2 idler pulley (if removed). Install and tighten bolt to specification. See TORQUE SPECIFICATIONS . Ensure idler pulley is clean and rotates smoothly. 2.Install No. 1 idler pulley and tension spring (if removed). Pry No. 1 idler pulley away from timing belt area as far as possible. Temporarily tighten No. 1 idler pulley bolt. Ensure idler pulley is clean and rotates smoothly. 3.Using crankshaft pulley bolt, rotate crankshaft so timing mark on crankshaft sprocket aligns with timing mark on oil pump housing. See. This will position keyway in crankshaft sprocket at 12 o'clock position.

CAUTION:If reusing timing belt, ensure reference marks on timing belt align with reference marks placed on crankshaft and camshaft sprockets. Ensure timing belt is installed in original direction of rotation.
4.Ensure all sprockets and idler pulleys are clean. Install timing belt on crankshaft sprocket, oil pump sprocket, No. 1 idler pulley, and then No. 2 idler pulley in sequence. 5.Install timing belt guide with cupped side away from crankshaft sprocket and flat side toward timing belt. Install No. 1 timing belt cover and new gasket. 6.Align crankshaft pulley key groove with key in crankshaft. Install crankshaft pulley. Install and tighten crankshaft pulley bolt to specification. 7.Rotate crankshaft clockwise so cylinder No. 1 is at TDC on compression stroke. Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover. If reusing timing belt, ensure reference mark on timing belt aligns with upper edge of No. 1 timing belt cover. 8.Rotate camshaft, and align hole in camshaft sprocket with alignment mark on camshaft bearing cap. See Fig. 2 . Install timing belt on camshaft sprocket. If reusing timing belt, ensure reference mark on timing belt aligns with the reference mark on camshaft sprocket. Ensure tension exists on timing belt between the crankshaft and camshaft sprockets.
CAUTION:DO NOT rotate crankshaft counterclockwise, as viewed from timing belt end of engine.
9.Loosen No. 1 idler pulley bolt 1/2 turn. Rotate crankshaft pulley 2 full revolutions clockwise from TDC to TDC. 10.Ensure timing mark on crankshaft pulley aligns with "0" mark on No. 1 timing belt cover, and hole in camshaft sprocket aligns with alignment mark on camshaft bearing cap. See Fig. 2 . If timing marks are not aligned, remove timing belt and reinstall. 11.Rotate crankshaft clockwise 1 and 7/8 revolutions and align crankshaft pulley "0" mark with 45-degree Before Top Dead Center (BTDC) mark on No. 1 timing belt cover. See Fig. 5 . 12.Tighten No. 1 idler pulley bolt to specification. See TORQUE SPECIFICATIONS . Install No. 2 timing belt cover and gaskets. Install and tighten spark plugs to specification. 13.To install remaining components, reverse removal procedure. Install all bolts/nuts on right (timing belt side) engine mount before tightening to specification. 14.On Camry, when installing control rod and bracket on strut tower and right (timing belt side engine mount, tighten bolts to specification in sequence. See Fig. 6 . On MR2, tighten engine
b7619be.jpg
92cabaf.jpg
Hope this helps, don't forget to rate.

Lazaruselite

Feb 25, 2009 | 1993 Toyota Camry V6

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

381 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...