Question about 1999 Chevrolet Silverado 1500

2 Answers

When i went to leave. when i went to put it in gear the colomn jusy went all the way down. what could cause this?

Posted by on

2 Answers

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Sergeant:

    An expert that has over 500 points.

    Champion:

    An expert who has answered 200 questions.

  • Expert
  • 226 Answers

The linkage rod from the outside column to the transmission selector came loose at the trans selector you will need a wrench and go under and set it back up for proper operation of all gears

Posted on Feb 04, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Expert
  • 55 Answers

The linkage from the column to your transmission may be the cause .
Put them together and try again .Look underneath your car where the steering wheel is towards the front a little ...you make someone shift the gears and you watch what happens .You may be able to see it where the problem is .It may be a pin that fell on the ground.

Posted on Feb 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My 99 Cougars manual transmission will not go into any gears at all


Check the cable under the gear lever. Look for broken pin or missing pin joining the lever to the cable

Mar 05, 2013 | 1999 Mercury Cougar

1 Answer

Clutch issues


This is a hydraulic clutch, meaning you push fluid to make the clutch move just like the brakes.
I would check the clutch master cylinder first to see if it is full of fluid.
The master or slave cylinder could have failed, among other things.
Grinding gears means the clutch disk is not moving.

Jul 01, 2012 | 2006 Saturn Vue

1 Answer

Horn repair at steering colomn


the center section where the horn button is should slide out with some resistance. then one large nut holds the steering wheel on usually accompanied by 2 or 3 small bolts to hold the horn actuator down. it takes a gear puller to actually remove the steering wheel. as for the steering column itself it's a conglomeration of lag screws and plastic covers.

May 17, 2012 | 2007 Nissan Frontier SE Crew Cab

1 Answer

Broken shifter cable, how do i repair it


Put park brake on or block wheels, and shift into neutral (if possible), If not go to tranny and pop the cable off the tranny lever (pry off with screwdriver). Turn tranny shift lever, until it clicks twice, leave here for later adjustment. Follow the cable to the adjuster, pull out the flat steel retainer clip, pinch the sides to remove cable from bracket. Remove upper covers below the steering wheel. Remove kick panel below steering colomn. Remove cable from steering wheel shifter assembly (pry off and remove clip same as at tranny). Remove the side kick panel and follow cable along floor. You may find it easier to remove the driver seat (4 nuts on floor and wiring). Pull cable thru floor and replace. Reverse procedure to install. Lock the cable and clip at steering colomn, but leave the clip off at tranny. The tranny should still be in neutral. Now turn key to run and shift the shifter into neutral. At the tranny side cable there is a white square button, press in and lock cable to lever. install retainer clip. move shifter thru ranges and ensure it locks in park. Readjust if needed by pressing button and moving shifter lever on tranny.

Jan 27, 2011 | 1995 Chevrolet Silverado 2500

1 Answer

Steering wheel moves 1/2 inch to the side


It sounds like the upper steering colomn bowl is loose. The bolts come up from the bottom and hold the lower portion of the steering wheel cover to the upper. The steering shaft runs down thru the middle of both. If loose the steering wheel will rock side to side in the upper bearing race, not holding the shaft tight or straight. Its actually easier to remove the entire steering colomn, turn upside down and tighten. Remove the lower steering shaft at the firewall (mark the spline alignment). Disconnect the electrical connections at the lower colomn. Disconnect shifter (if not floor console shifter). Unbolt from dash and remove the entire colomn, with wheel attached. Flip over and chek the lower bolts for tightness. It can be done from disassembling the colomn, but its a lot of work and lots of little pieces to loose.

Jan 26, 2011 | 1987 Chevrolet El Camino

2 Answers

2001 ford taurus Went to store with no problems went to leave car will shift through all gears without holding brake but will not move. You can here the car idle up and down when you change gears but it...


has the oil in the auto box been checked latly,it sound like the oil pressure is not building up in the autobox ,has there been an oil leak where the car was parked?if the engine is idleing up and down then its not the soloined,need to check oil first if that ok then i would say oil seal.adrian,,,,,,

Aug 12, 2010 | 1999 Ford Taurus

1 Answer

I have a 2003 Chevy Impala, automatic. It drove fine all day and last night when I went to leave a friends I went to put it into drive, nothing, the shifter can be pushed in to all the gears and it wont go...


That is true. I could be a simple as that breaking off. Had that happen to my Mazda 626 just this past winter. Thought it was a 1700 dollar fix and it ended up being a 26 dollar fix.

Jul 05, 2009 | 2003 Chevrolet Impala

1 Answer

Subaru will not go in to gear was work fine and then jusy stop going into gear


Check your shift linkage. If your shift linkage got out of place it would be possible that you cannot shift into gear.

Mar 08, 2009 | 2007 Subaru Impreza WRX STI Limited Sedan

Not finding what you are looking for?
1999 Chevrolet Silverado 1500 Logo

166 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75066 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7754 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...