Question about 1995 Lexus ES 300

1 Answer

How do I change the right license plate bulb. Do not see easy access from plate area in trunk. Or do I pop off piece around bulb on outside to change? 1995 Lexus ES300

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 81 Answers

This ones kind of tough for an amateur. You need to pop off most of the little black retainers holding the trunk lid liner on. then theres the emergency handle that you use to get out if your locked in the trunk. you need to pull on the far end of the handle and the outer cover will come off. you may need a small screwdriver to remove it. then pull straight down, really hard and the handle will come off. then remove the rest of the liner. the bulbs are 194a bulbs. available pretty much anywhere. reinstall in the reverse order.

Posted on Feb 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace license plate bulb on 2004 Buick Century


You have to take out the entire back lights, Inside the trunk pull back the material and unscrew those plastic lugs. (Some years have lights on trunk when opened or under) But in my 01 the lights come up with the trunk. Remove those lugs. Take off the entire rear light assembly. You'll have easy access to the License plate bulbs. Sounds complicated but it takes a total of 10 minutes total. While your at it wash the area where the lights were on. A coat of wax left on will keep the water, moisture from rotting the surfaces. Make sure your seals are good and re-install. If the bolts are rusting put a small amount of grease on them. (Prior to re-installation of course)

Dec 01, 2016 | 2004 Buick Century

1 Answer

I am trying to replace my license plate light as it is out. I know how to change the bulb, but I don't know what bulb I need.


You need to pop the trunk and look behind the back plate.these lights are usually 5watt small bayonet types and easy to spot if filament has burned or broken.

Feb 19, 2015 | 2000 Pontiac Grand Am GT

1 Answer

Need to replace bulbs that lights license plate. License plate and light is part of trunk


raise trunk lid look on the inside behind your license plate light there should be access to the bulb there. You will see the wires going in to the bulb there will either be a flt plate that can be removed to access bulb or where the wires enter there will be a round socket that you can twist counter clockwise and remove the bulb socket for bulb replacement. hope this helps.

Jan 15, 2011 | 2003 Lincoln Town Car

1 Answer

How to replace license plate lights


    Follow the Steps on how to replace license plate light on your car.

    1. Open the trunk and locate the trunk liner retainer clips.Use the Phillips head screwdriver to loosen the center plastic screw of the retainer clip about 1/4 turn, just enough to raise the head of the screw from the base of the clip. Pull the screw up, and lift the clip out of the liner. Use a flathead screwdriver to help pry it out. Remove enough of the clips to allow access to the license plate light sockets. Pull the liner back.

    2. Remove the emergency trunk release handle by popping off the top cover of the handle. Use the needle nose pliers to gently squeeze the prongs on the shaft, while removing the handle.

    3. Unplug the wire harness from the license plate light bulb socket the release clip on the side of the outlet.Twist the license plate light bulb socket 1/4 turn counterclockwise, using the needle nose pliers again. Do not apply too much pressure to the pliers; you may damage the socket.

    4. Remove the bulb from the socket, and replace it with a new one.

    5. Replace the socket into the socket assembly, and plug the wire harness back in. Test the bulb by turning on the lights of the Corolla, then turn them off again.

    6. Replace the trunk emergency release handle, and replace the hood liner and the retainer clips. Remove the old bulb and tools, and close the trunk.

Dec 22, 2010 | 1995 Toyota Corolla

2 Answers

Access to tail light wiring harness plug


You have to remove the access panel on the interior side of the passenger compartment to access that connector.. it's a simple procedure after you see the wire harness and bulkhead boot.

May 09, 2009 | 2002 Hyundai Santa Fe

1 Answer

License plate bulb 99 alero


remove the 2 license lamp screws from outside,above the lic.plate then from insidethe trunk pull up the lic.lamp housing and replace the bulb.it should pull straight out

Apr 21, 2009 | Oldsmobile Alero Cars & Trucks

2 Answers

License plate bulb on 1997 Cadillac deville


this is straight out of the book ok



  1. Open the rear compartment lid.
  2. Remove the rear compartment lid trim.
  3. Pull back on the rear compartment trim panel.
  4. Unplug the lamp connector from the rear compartment lid wiring harness.
  5. Press the grommet out of the rear compartment lid.
  6. Remove the nuts retaining the lamp assembly to the rear compartment lid.
  7. Remove the bulb.

Mar 07, 2009 | 1997 Cadillac DeVille

3 Answers

Licence light replacement 1996 Cadillac Deville


remove your license and behind it you will find i think two screws then remove that panel and you should be able to get to it.

Jan 22, 2009 | 1996 Cadillac DeVille

2 Answers

Change tag bulb 2000 focus


am not familiar with the early year Focus'. Look above the license plate, if the lens for the bulb has two screws, you need to remove them to access the bulb. On other models, open the trunk and look down where the license plate is, you should be able to see and access the bulb from there.

Jul 19, 2008 | 2000 Ford Focus

1 Answer

License plate lights in the trunk lid.


The license plate bulb is replaced by removing the two scews that hold the lens in place and pulling the lamp housing out of the trim plate the removing the socket.

Jul 15, 2008 | 1998 Buick LeSabre

Not finding what you are looking for?
1995 Lexus ES 300 Logo

216 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lexus Experts

yadayada
yadayada

Level 3 Expert

75051 Answers

ROBERT GARCIA
ROBERT GARCIA

Level 3 Expert

874 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Lexus Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...