Question about 2003 Chevrolet TrailBlazer

1 Answer

Had a test done and it said it is the camshft/crankshaft censor where is it located and how do i remove it. Check engine light came on and it started to idle rough. I changed fuel filter and sparkplugs then took it to monroe muffler they did a test and told me it was the above problem. I just need to know where it is located and how to remove it.

Posted by on

  • vnbliq Feb 03, 2010

    well I found and changed camshaft sensor and it did not help it actually made it worse. Now I cant run my heater while the car is running or it will turn off. I have no idea what to do now and i cannot read spanish sorry.

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

  • Contributor
  • 4 Answers

Precisoooo de um numero de serial do nero media player sera que é possivel

Posted on Feb 03, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is a crankshaft positioning censor location on a 1989 Chevrolet celebrity 2.8 multiport fuel injection


It is located under hood, center, rear engine area back side of the engine block, it picks up its signal off the crankshaft throw. See picture below
26293690-igh0mp2c2a55vdmoomvc2bzi-2-0.jpg

Sep 27, 2016 | Chevrolet Cars & Trucks

1 Answer

Where is the crankshaft position sensor located on the 2002 Mitsubishi Montero sport xls 3.5 truck.


Hi David, The link below is how to test the crank sensor (1997-2004 3.0l Montero, Hope this helps......CHEERS
http://easyautodiagnostics.com/mitsubishi/3.0L/crankshaft-position-sensor-test-1#3
The crankshaft position (CKP) sensor is located behind the timing belt... but testing it is done without removing the timing belt or its components. This is due to the fact that the crank sensor's connector is located on top of the engine and in plain view (next to the ignition control module). In the photo below, the orange arrow points to the location of the crankshaft position sensor connectors (photo applies to: 3.0L 1997-2004 Montero Sport).

Mar 31, 2016 | Mitsubishi Cars & Trucks

1 Answer

How to install a camshft position sensor in 2000 windstar


Please tell me did you test crankshaft position sensor?
It is relatively easy to replace it. It is located on the right side of the engine on transmission bell housing below electronic ignition coil. Remove negative battery terminal, unplug the connector from sensor and remove it. Installation is in reverse of removal.

Dec 29, 2013 | 2000 Ford Windstar

1 Answer

Crankshaft sensor on a 2000nissan xterra where is it located and how can it be replaced


crankshaft position sensor location for 3.3 V6 engine is mounted at the rear of the engine on transmission bellhousing, the 3.5 V6 engine crankshaft sensor located at front of the engine on the aluminum oil pan section below crankshaft pulley.replace the crankshaft position sensor remove heat shield disconnect the electrical connector the remove sensor retaining bolt then remove crankshaft sensor.after replacing crankshaft sensor you need to erase code if check light come back on.

Nov 14, 2011 | 2000 Nissan Xterra

2 Answers

My Nissan Altima 1997 has a Engine Check light on. I brought it to an Autozone for diagnostic. The test result showed that the probable cause is a Crankshaft Sensor (CS). I want to replace it but I don't...


cs sensor is beside crankshaft pulley side of motor look for electrical plug. or could be inside crankshaft pulley, some are made that way, if so you'll have to pull harmonic balancer to get it out. hope i helped!!!

Aug 16, 2010 | 1996 Nissan Altima

1 Answer

No spark got gas


If you have access to a scan tool you can check and see if the scan tool shows any RPM's while cranking this indicates whether the pcm is receiving a signal from the crankshaft sensor.The crank sensor is generally located on the rightside of the car lower engine by the cranskshaft pully/dampener.Before going this route would check the ignition module which is right by the coils underneath the coil cover many auto parts stores can test these for you.

May 14, 2010 | 1996 Chevrolet Cavalier

2 Answers

CAN NOT LOCATE THE CRANKSHAFT POSITION CENSOR ON MY 1996 INTREPID


It should be on the transmission by the passenger side of car. It has three wires connected to it.
1998 Dodge Intrepid
the crank sensor is on the passenger side of the car on the back of the engine. Check right up there by the transmission housing.
1994 Dodge Intrepid 3.3 liter

Jan 01, 2010 | 1996 Dodge Intrepid

1 Answer

How to time up a ford fiesta 12.5 on a y reg for


(you need a set of timing tools to do this)you need to place timing pin in engine block located drivers side just above the sump you need to set pistons at tdc to do this turn crankshaft clockwise till the crank stops against the pin then you need to take off the rocker cover place cam setting bar in the end of camshfts you then need to loosen cam sprockets dont remove undo tensioner remove belt replace with new starting at crank anticlockwise tension up tighten cam sprockets remove bar and pins 2 rotations by hand to see if everything ok then start

Dec 13, 2009 | 2000 Ford Focus

1 Answer

Dodge 2500 5.7 crankshaft censor replacment


The crank sensor is located on the right or passenger side of the engine, at the back on top of the transmission bell housing. It is held in with two bolts and has a single electrical plug on it. Hope this helps and good luck.

Jan 17, 2009 | 2005 Dodge Ram 2500 Truck

2 Answers

Crank positioning censor


The camshaft position sensor is located on the timing cover on the front of the engine. The crankshaft position sensor is located just above the differential on the transaxle bell housing where it has to be to read from the flywheel the position of the crankshaft. It is easy to see from the front of the engine even though it is on the back half. Just look for the shifter cable and where its bracket ends (on the firewall side of the bracket) glance about 12" to the left and you should have no problem finding it. An 8 mm bolt is holding it in and with that bolt taken out it just pulls out of its hole. Google "95 caravan crankshaft position sensor" and then pick IMAGES so you can see an actual picture of what it looks like.

Aug 01, 2008 | 1995 Dodge Caravan

Not finding what you are looking for?
2003 Chevrolet TrailBlazer Logo

97 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75817 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8180 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...