Question about 2000 Chevrolet Venture

1 Answer

I have the battery and all bolts wires etc. out but it is stuk with something else, like its glued in.

Posted by on

  • mtatnall May 11, 2010

    is there and locking block bolted down on one side?

×

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 5 Answers

There is a Battery hold down that needs to be unbolted at the bottom of the battery on the side the right front fender is on. The nut for that bolt is part of the bottom of the battery case. I had one rusted solid and I had to use a 2x2 piece of wood to pry the battery out and replace the battery hold down.

Posted on Feb 16, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuk camshaft pulley


if that eagle has a 2.0 then your talking about the camshaft gear or is it the crank shaft pulley . then your gonna have to use the gear puller with the two arms and use the thin ones and turn them inside out but if its the small gear just use the two jaw puller and wrap a ratchet strap around the puller to where the jaw puller claws are on snug and use the strap and tighten it down and screw in the center bolt use an inpact wrench just hit the trigger enough to where it gives it a slamming affect . this will jar it lose dont use no hammer .

Mar 21, 2014 | 1995 Eagle Talon

1 Answer

Remove upper oil pan on 94 ford probe have it loose wont come off


sum pans on original engines are glued on at the gasket. You may have to use something like a wood chisel to break the seal between the pan flange and the crank case edge.

Mar 05, 2014 | Cars & Trucks

2 Answers

My mitsubishi diamnte starter will not shut off


the start relay is sticking or the selenoid on the starter is stuk

Nov 28, 2013 | 1997 Mitsubishi Diamante

1 Answer

Lose connection


reconnect and support the wires so that the strain is not pulling apart. Something simple like a paddle pop stick over the connection tied on with zip ties and zip tie the wires to something handy--- pipe, bolt bracket etc

May 09, 2013 | Cars & Trucks

1 Answer

Car clicked several times had it jumped to make it home. Next day removed battery which tested to be bad. Replaced battery and now it does nothing. No lights, radio etc. Alarm did go off and doors locked...


Check the battery connections. This is a common problem and the first thing that should be checked when a problem like this occurs. If you can move the cables at all this is your problem.

Make sure the cables are clean; use a wire brush or sandpaper to clean them up. Tighten the bolts so that the clamps are tight and you can't move the cables whatsoever.

Make sure your red wire goes to the positive + side of the battery and negative - to the negative side.

Feb 20, 2011 | 2001 Ford Escort ZX2

1 Answer

On my 96 jeep cherokee sport my key is stuk in the ignition with it stuck on acc mode i had to discoonect the battery to keep it from draining how do i replace the hole switch


I have that problem at times and mine I just have to push the automatic shifter forward towards park... there is spot where it lets your key free... It might be something else but I have grown used to pushing that shifter all the way with a little extra force...

Aug 03, 2010 | 1996 Jeep Cherokee

1 Answer

Took out oil pan bolts and bell housingbolts and oil pan will not come off .is there an alignment pin or something?


there should be 2 x pins,both in bottom of block,one front/one rear but pan is glued on.....as well as bolted.pull harder....

Jan 11, 2010 | 2000 Volkswagen Beetle

2 Answers

Can you disable car alarm in 1991 Acura Legend by


If it's a cheap aftermarket alarm, check for a red wire coming off the hot side of your battery with an inline fuse. If it's not, try to locate the alarm "computer" under the driver's side dash or nearby your fuse panel. You'll find a black box with a wiring diagram glued to the side, normally strapped to a wiring harness or other fixed element. If this is the type of alarm you have, you'll need to trace each wire coming from the alarm computer and unclip each fastener that's clipped to your vehicle's factory wiring. The trouble with these types of alarms is that they can get power from a number of sources (stereo, interior lights, etc.). Good luck with this one!

Jun 12, 2009 | 1991 Acura Integra Hatchback

1 Answer

Removal of Oil pan


did you try giving it a gentle smack with a rubber hammer? these pans are usually glued on with silicone and will not just fall off after unbolting... sometimes you need to get something like a paint scraper and slide it between block and rail to seperate the two.

Jan 17, 2009 | 1996 Pontiac Grand Am

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

20 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7768 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...