Question about 2000 Chevrolet Venture

1 Answer

The pully on the cam shaft is out of line with the other pulleys WHY?

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Genius:

    An expert who has answered 1,000 questions.

  • Master
  • 1,098 Answers

It sounds like it has been poorly fitted, check the centre of the pully wheel and se if it sat correctly on the shaft end. if you can loosen the belt and tap the centre of the wheel to see if it re-aligns, be careful driving it, in fact I would not drive it at all until it looked correct.

I had a similar fault on another car one of the bolts hokding the pully wheel had came loose and fell out there was 3 bolts on this car, not sure on yours but do chcek they are all tight and be sure to tighten them evenly half a turn each then move to the next etc etc.

hope this helps
regards
dan

Posted on Feb 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trying to time the cams shafts to the belt pullys there no notches only 3 bolt holes


You really need the Cam Tool that holds the Cams in place from the opposite end of the head as the Pulleys. There is also a Tool to hold the Cam Pulleys as well. IPD sells it for near $280 and that also includes the guides for the Cam Cover and a set up to evenly press the cam cover in place. The Cams will have a groove where the tool holds them and you will need to find out how they are supposed to be set. Just be happy you are not dealing with a Variable Cam Timing set up.

Feb 04, 2013 | 1999 Volvo S70

1 Answer

Timing marks mitsubushi l200 warrior


  • No 1 piston at TDC on the firing stroke.
  • crankshaft pulley notch in line with TDC mark on timing covet
  • cam shaft pully notch in line with mark on head
If it has dizzy then No1 at tdc will have rotoe pointing on number 1 lead.
if has Igniters then line notches on cam to notches on head

Sep 23, 2011 | Mitsubishi Pickup Cars & Trucks

3 Answers

How to set timing when you relesh tensioner and it changes the alignment postion of pullies 2000 ford ranger 2.5 l


Here is the trick. Align marks. Put the timing belt on the crank shaft pulley first, and after on the overhead cam pulley. Release tensioner and rotate the crank shaft till the timing belt makes two full circles. Try to align marks, you will be at least one tooth off. Align the crank shaft on the mark, and find out how many teeth you are off at the cam shaft pulley. Count the teeth. Remove the timing belt from cam shaft pulley only. Move cam shaft pulley in reverse according to the number of teeth you counted. Make sure the crank shaft pulley is on the mark. Mount the belt at cam shaft pulley.Rotate the belt two circles and check the marks. Repeate this procedure til after releasing the tensioner, and rotating the timing belt two full circles, the mars will be align.

Nov 22, 2010 | 2000 Ford Ranger SuperCab

1 Answer

1999 ford ranger timing marks 2.5


One is on the crank shaft pully (for TDC). It is a line, scribed on the pully, that alligns to a pointer on the plastic timing belt cover. The second is on the cam shaft pully. It can be accessed by removing the rubber inspection plug on the timing belt cover. The third is on the auxillary shaft (oil pump) and is also accessed through an inspection plug on the timing belt cover.

On the cam and oil pump pullies, the diamond aligns to the diamond and the triangle aligns to the triangle (the pullies have both). These should be perfectly aligned when the crankshaft pully line is at 0 deg TDC. If you can't see the marks through the inspection port while the crank is at 0 TDC, you are 180 degrees out - turn the crank one more time. 

Sep 12, 2010 | 1999 Ford Ranger SuperCab

1 Answer

How do i time my Golf 1 correctly? it consumes a lot


its tricky enough if your not sure what your doing but ill run you through it. 1. remove top rocker cover and timing belt cover. 2 make up the position of the pully on the cam shaft at the top and the drive shaft at the bottom, this marks are you fail safe incase you cant time the engine. 3 remove the timing belt and pully tentioner, note if your going this far you are as well to replace the timing belt,tentioner and water pump. 4 On the cam shaft at the top if you force them to turn you will see a small indicator mark on the shaft this mark has to line up with the other indicator mark on the housing between the cam shaft and the cam shaft pully, once they line up your top end is timed, mark up the pully incase it moves. 5 on the drive shaft pully there is also markings that have to line up but you can also feel the position of the pully as you turn it, you will feel the piston been forced up and it is timed at top dead centre on cylinder one, which means the the piston has to be at the top just before the point of returning back down, using your feeling as a guide and the markings lined up you will have timing. also mark up this pully, your new marking should be very very close to the fail safe markings you put on at the start. when you have your marking replace the timing belt with the longest distance between pully contact going on first, try not disturb your timing or your hard work will have been for nothing, make sure the tentioner on the belt is tight but not to tight to the point where you ll stretch the belt or snap it, put everything back as you found it and crank the engine, job done, best of luck. hope this helps( rate me on my answer thanks )

Aug 27, 2010 | 2000 Volkswagen Golf

1 Answer

Diagram of changing a 2000 model nissan xterra timing belt


I am assuming you have the 3.3 litter v-6?cf56ba7.gifI just did my own so I can offer you a few words of personal advice. Make sure, before you remove the crank shaft pulley, that the engine is at TDC. There is a pointer on the lower timing cover that should line up with the mark that is furthest to the left on the crank pulley (looking at it from the front of the truck). If you are replacing the timing belt for maintenance, not failure, make several marks on the cam pullies to the rear of the timing cover with a paint pen before removing the old belt and make sure that everything stays aligned to those marks upon reassembly. If this method is not an option, use the timing dimples on the back of the upper timing cover only as reference points for the cam pulleis (this is where I ran in to trouble). What is most important is that there are exactly 40 teeth on the belt between the marks on the cam pullies and 43 teeth between the right cam pully mark (right cam as you look at the engine from the front of the truck) and the mark on the crank pully. I used a Goodyear Belt that actually had marks that indicated the 40 and 43 tooth increments. Make sure you have the belt on the right directon, arrows to the front of the truck. Again it is very important that the crank pully remain at TDC (top dead center) during the entire process. Good luck, hope you get it the first time and not the second like me!!

Jan 27, 2010 | 2000 Nissan Xterra

1 Answer

How easy is it to change water pump gasket on 91


There are two pulleys running in this engine, and the waterpump runs on the second pully behind a case. so you have to take almost everything off to get at it. Then, the waterpump is actually the belt tensioner for that pulley system. it is excentric (sp?) so when you turn it in place, it tightens the belt. then you secure it back with three bolts. The belt system in question connects the drive shaft with the cam shaft, So you do have to be Very Careful with the belt/ pulley alignment. i marked the pulleys very very carefully so i could get everything lined up again.

Oct 16, 2009 | 1991 Pontiac Sunbird

1 Answer

Fitting cam shafts on Volvo 850se 1994 20v 2ltr


There is a special tool that mechanics use for the alignment of the camshaft pullys. It is basically an angle iron straight edge that fit exactly into the camshft grooves.. Just make sure that the engine 's first cylinder is at the top. (Top dead center) before fitting the cam(s) into place.

Feb 06, 2009 | 1994 Volvo 850

1 Answer

Need 2 no where timing marks are for 86 hilux 2188cc diesel


Hey NewK, Try looking under the Cam Pully If ya got the radiator out Its at the lowest point Fuunyist thing I ever seen but thats where it is. Heres a tip if ya radiator is still in the vehical Use a small mirror to help you see the Underside of the pully......................Tight Nutz, Donkuz.

Jan 02, 2009 | 1995 Toyota 4Runner

1 Answer

Timing marks for 91 volvo


The balance shaft pulley should be sitting at 4 o'clock, the crank pulley should be setting at 12 o'clock, and the cam pulley should be set even with the edge of the cylinder head at about 11 o'clock. You may have to set the distributor forward or back a little t get it running right.

Nov 22, 2008 | 1991 Volvo 740

Not finding what you are looking for?
2000 Chevrolet Venture Logo

Related Topics:

31 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

77186 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Ronny Bennett Sr.
Ronny Bennett Sr.

Level 3 Expert

6927 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...