Question about 1992 GMC Jimmy

1 Answer

The check gauge ligth in the board is flashing

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 50 Answers

If light is flashing you are probably running rich. This could damage converters. Get it fixed and save lots of fuel mileage/

Posted on Mar 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Problem w/gauges they will flash on while driving stop working then go back to normal.


problem could be in instrument panel circuit. a wire might be broke or melted on the circuit board. may have intermitting touch of broken wire causing gauges and lights to flash on an off.

Mar 31, 2015 | 2008 Ford Taurus SEL

1 Answer

I am getting hold ligth on on my dash board,when i start the engine,the engine fuse break,i have change the alternator n check all the fuses,if i disconnect the wiring from the alternator the engine runs...


There might be a short between the alternater and ground.
Check wiring
Disconnect battery and alternater wiring from the back of the alternater and with a multimeter check for continuity between the BAT stud on the back and the alternater housing.There shouldn't be any.

Apr 18, 2011 | 1990 Mazda 929

1 Answer

GOT A 99 GMC SONOMA. THE VOLT GAUGE WAS SHOWIN BETWEEN 9 & 14 VOLTS. HAD BATTERY CHECKED,THEY SAID IT WAS BAD. GOT NEW BATTERY N IT DID SAME THING. GOT ANOTHER ALTENATOR,PUT IT ON NOW IT SHOWIN BOUT...


11-12 IS GOOD WITH RUNNING NOTHING ON WHATS IT ON . NOW TURN JUST HEAD LIGTHS ON DID IT MOVE ANY MAYBE 1-2 METERS THATS FINE . DRIVE IT!!!!!!!!!!!!!!

Dec 12, 2010 | 1999 GMC Sonoma

1 Answer

I have a Toyota Echo 2004 , the fuel tank indicator on the instrument panel stop working even if the car is completely full the ligth is on , indicating low fuel.


There is a flotation operated sender inside the gas tank, which provides information to the gauge.
Either your sender has died or become corrupted by taking on gas, or the gauge has died. Probably easier cheaper and faster to have the gauge checked out at a dealer than to pull the tank out. Might be a common problem on that model or year. Ask a dealer service department how much to figure it out.

Oct 08, 2010 | Toyota ECHO Cars & Trucks

2 Answers

My gauge ligth is on and my oil and engine ligth on? why thats happening maybe my mechanic put the wrong oil???


The "wrong oil" wouldn't do that - not immediately, anyway. More probable is they may have forgotten to fill the engine with oil when they changed it last. Have you checked the dipstick to see if the oil level is correct? If you do not see oil on the dipstick, do NOT run the engine! Have it towed to a different mechanic, and have it inspected to see if there is any permanent engine damage. You may have cause for a claim against your mechanic.

Sep 30, 2010 | Ford F-250 Cars & Trucks

1 Answer

Flashing ligth not working at all


Hi!!!

If your hazard lights turn on but do not blink, replace flasher.

If your hazard lights don't turn on, check hazard/stop/turn fuse(s).

Let me know how it worked out, good luck.

Mar 26, 2010 | 1998 Ford Windstar

1 Answer

Oil ligth stay's on


Locate oil pressure sending unit and unplug the wire. Be sure it touches nothing and check to see if light went out. If it did replace the sending unit. If not I recommend seeing a tech to install manual oil pressure gauge to check actual oil pressure and go from there.

Aug 02, 2008 | Chevrolet TrailBlazer EXT Cars & Trucks

Not finding what you are looking for?
1992 GMC Jimmy Logo

Related Topics:

39 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

76051 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...