Question about 1994 Lincoln Town Car

1 Answer

Rear brake lines must be replaced on '94 Town Car

Can I access the brake line proportioning block by removing the left front inner fender panel on a 1994 Lincoln Town Car? The brake lines to the rear wheels must be replaced and the fittings where the lines tie into up by the master cylinder can't be reached from underneath the car. It looks like the drivers side exhaust manifold must be removed to get access from underneath and I don't want to do that.

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 1,068 Answers

Yes you can i have had this issue before and it is a pain in the rear! lol... i think i have also got it from above reaching down also. let me know if you need more help. funny i must have done 4 brake line jobs on town cars in the last month. now you ask about it. before them i haven't seen one in years. lol.... good luck

Posted on Feb 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to remove rear A/C expansion valve on 2001 Chrysler Town and Country


Next remove the rear seats or stow them. Then remove all the trim panels from the passenger rear of the vehicle. You will then be able to see the rear HVAC assembly.

Jack up the vehicle and support it properly. remove the nut that holds the rear lines to the expansion block.

Remove the heater core form the HVAC module with the cooling lines still attatched. Remove the HVAC module from the vehicle.

You will then be able to replace the rear evap core/tubes/expansion valve.

Get the kit from the dodge dealer. It will make life very easy.

Aug 13, 2015 | 2001 Chrysler Town & Country

1 Answer

I need to know if a brake line Junction Block is the same as a proportioning valve?


no a brake line junction block will give all of the brakes equal pressure and wear the back brakes out faster then the front if your car is not made for it a proportioning valve monitors the pressure on each brake and distributes it accordingly

May 12, 2011 | 1998 Ford Taurus

1 Answer

88 t-bird non abs. the front brakes drag. i have replaced all rubber lines also new master cyl. new front brake calipers. rear brake hose preasure will bleed of after it has set for 15 to 20 min.can...


This is bizarre... I'm suspecting dirt in line(s). Are you bleeding correctly? Starting w/ Right rear, left rear, right front, then left front. You might try using a power bleeder also. A possible long shot, is brake proportioning valve sticking.

Mar 21, 2011 | Ford Thunderbird Cars & Trucks

1 Answer

Repair and replace propation block for brakes


This part is better of replaced, you will need to remove the brake lines first and make a diagram to label the location of the lines as you remove them and then install new valve and bleed brake system starting at the right rear then go to left rear then left front and last right front.

Jan 23, 2011 | 1984 Chevrolet Blazer

1 Answer

How do i replace left door mirior


remove trim panel, remove mirror fasteners.

Glass, Outside Mirror—Town Car

Removal and Installation
  1. Push upper edge of outside rear view mirror glass (17K707) into the outside rear view mirror to expose latch release.
  1. Using a small flat-bladed screw driver or equivalent, move latch release to released position.
  1. Remove outside rear view mirror glass mounting back and outside rear view mirror glass from outside rear view mirror.
  1. Disconnect heater wire connectors and auto dimmer connector, if equipped.
  1. To install reverse Removal procedure.
------------------------------------------------------------
Mirror, Power—Outside Rear View
Town Car

Removal and Installation
  1. Disconnect battery ground cable (14301). Refer to Section 14-01 .
  1. Remove front door trim panel (23942). Refer to Section 01-05 .
Trim Panels, Door Front—Town Car
Removal
  1. Snap out two door pull strap retaining screw covers. Remove screws.
  1. Remove three screws on front and rear side and center of front door trim panel (23942).
  1. NOTE: The following procedure must be used during removal and installation of the door armrest and trim panel. Refer to the appropriate illustrations for component and vehicle model identification.

    Using the Trim Pad Removing Tool from Rotunda Windshield and Moulding/Trim Removal Kit 107-R0401 or equivalent, pry the trim panel retaining clips from the door inner panel.
  1. NOTE: Do not use front door trim panel to remove trim clips from door inner panel. Replace any bent, damaged or missing push pins.

    Remove window regulator control switch housing from front door trim panel. Lift up housing in front and disconnect all connectors.
  1. Disconnect wiring harness and heated seat switch electrical connectors if equipped.
  1. Remove the door trim panel.
  1. Disconnect two electrical connectors.
  1. Remove nut from outside rear view mirror mounting base.
  1. Swing outside rear view mirror (17682) toward driver door window glass to expose screw in mount base.
  1. Remove screw from outside rear view mirror base.
  1. Remove outside rear view mirror from front door (20124). Guide wiring and connectors through hole in front door.
  1. To install, reverse Removal procedure. Tighten nuts to 8-10 Nm (71-88 lb-

Nov 05, 2009 | 1996 Lincoln Town Car

1 Answer

Very little (almost nonexistent) rear brakes. Cannot stop rear wheels even with wheels off the ground. Replaced MC, wheel cyl.,Rubber hose, booster, proportioning valve, bypassed rear ABS, shoes, drums,...


What happens when you try to bleed the rear brakes? If nothing comes out, trace each line back toward the proportioning valve--something would be blocking flow of fluid. Disconnect each line at the forward end and see if fluid comes out of the valve openings. You will need a scan tool to complete the bleeding process with ABS. Suggest buying a Chilton's manual for this truck because of the complexity of the ABS system.

Sep 30, 2009 | 1997 Dodge Dakota

1 Answer

I need a diagram of the entire breaking system on a 1993 ford taurus i just replaced a rear line and i think i stripped the extention piece i had to add to the end of the break line. the one that goes into...


here is a 96 taurus

65160c0.gif
Item Part Number Description 1 2C296 Anti-Lock Brake Tube 2 2C219 Anti-Lock Brake Module 3 2005 Power Brake Booster 4 2263 Front Brake Tube 5 2B091 Brake Pressure Control Valve 6 2140 Brake Master Cylinder 7 2B547 Brake Load Sensor Proportioning Valve 8 N802191-S60 Bolt 9 2L568 RH Rear Brake Tube 10 2L569 LH Rear Brake Tube 11 2C287 Brake Fluid Distributor Tube 12 N808531-S301 Bolt 13 — Front Side Member 14 N802324-S56 Bolt 15 18124 Front Shock Absorber 16 2B121 Front Disc Brake Caliper 17 2078 Front Brake Hose 18 2264 Front Brake Tube 19 2553 Rear Disc Brake Caliper 20 2A442 Rear Wheel Brake Hose 21 N808728-S60 Bolt 22 — Side Rail 23 N802324-S60 Bolt
Brake Load Sensor Proportioning Valve

ef68fd0.gif
Item Part Number Description 1 2B547 Brake Load Sensor Proportioning Valve 2 — Body 3 N802191-S56 Bolt (2 Req'd) 4 2L568 Brake Tube Assy 5 2L569 Brake Tube Assy 6 2265 Brake Tube Assy 7 2B255 Brake Tube Assy 8 5500 Rear Suspension Arm and Bushing 9 W611634-S301 Bolt A — Tighten to 11.4-15.6 Nm
(8-12 Lb-Ft) B — Tighten to 10-14 Nm (7-10 Lb-Ft)

Brake Hose, Rear —Drum

ffe78ea.gif
Item Part Number Description 1 — Rear Side Rail 2 2L569 Rear Brake Tube 3 N602324-S60 Screw 4 N611193-S60 Screw 5 2C023 Left Hand Rear Hose and Connector 6 2210 Rear Drum Brake Backing Plate 7 18125 Rear Shock Absorber 8 2267 Rear Brake Tube A — Tighten to 16-20 Nm (12-15 Lb-Ft)

May 10, 2009 | 1993 Ford Taurus

1 Answer

No side lights or rear lights


You have a caroded or broken connection on the right inner fender skirt. Check your connection plug also for corrosion. The power goes out of the fuse block on the left fender across the front to right fender then to the rear taillights.

Dec 29, 2008 | 1998 Lincoln Town Car

1 Answer

Back brakes won,t bleed


you can prevent it from inflating by wearing a anti staic bracelet. it has an alligator clip that will attach to a ground. just take your time and you will do allright. when bleeding brakes always start with the right rear then the left rear then right front and finally left front. this is a two man operation. please rate this solution thanks

Aug 30, 2008 | 1990 Buick Reatta

Not finding what you are looking for?
1994 Lincoln Town Car Logo

Related Topics:

51 people viewed this question

Ask a Question

Usually answered in minutes!

Top Lincoln Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

fordexpert

Level 3 Expert

5501 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Are you a Lincoln Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...