Question about 2006 GMC Sierra

3 Answers

Changed front discs and pads on astra mk 5 sri but now brake pedal goes down half way befor working but if you press again quick its fine

Posted by on

3 Answers

  • Level 1:

    An expert who has achieved level 1.

    Corporal:

    An expert that has over 10 points.

    Mayor:

    An expert whose answer got voted for 2 times.

    Problem Solver:

    An expert who has answered 5 questions.

  • Contributor
  • 16 Answers

Did you push the pedal all the way to the floor first time,or did you pump several short pumps,if the former you may have damaged a seal in the master cylinder,the correct way is to open the bleed nipple as u force back the piston in the caliper,if the later,just take it for a test drive+the brakes should bed themselves in, from a vauxhall tech

Posted on Feb 01, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

    Sergeant:

    An expert that has over 500 points.

  • Expert
  • 212 Answers

MAKE SURE YOU HAVE NO AIR IN SYSTEM,YOUR MASTER CYLENDER MAY HAVE WORN SEALS,REPLACE WITH NEW OR REBUILT UNIT.

Posted on Feb 01, 2010

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Expert
  • 303 Answers

If you opened the bleaders you got air in the system and need to have it blead

Posted on Feb 02, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Brake peddle is low,


Pedal, not peddle. First make sure reservoir is full at the brake master cylinder. Then check your brake pads (for disc brakes) and/or brake shoes (for drum brakes). When the pads or shoes are very worn down, you will get a low pedal. If you have disc brakes on the front and drums on the rear wheels, first try just replacing the front brake pads. If you get a good pedal after the front is done, many people tend to let the rear brake shoes go unless they are making noise. These systems are designed to put most of the braking force on the front discs, so the rear shoes do not need changing as often.

May 11, 2017 | Cars & Trucks

1 Answer

I have 2003 astra Sri Turbo ts hatch the engine light is staying on but the car runs fine? Suggestions on what it could be?


Tags location of knock sensor

https://outofthebooks.top/term/location-of-knock-sensor
Need to locate knock sensor on 1999 camry V6. Where is ... Cabin filter · I have 2003 astra Sri Turbo ts hatch the engine light is staying on but the car runs fine?

Common problems with the Astra G [Archive] - Astra Owners Network ...

www.astraownersnetwork.co.uk > ... > Astra Chat > Astra G

Mar 20, 2007 - 100+ posts - ‎100+ authors
Also, rear disc brakes on the SRi models have a tendancy to seize up ... Pre 2003 2.2i.... about 10mins but the engine temperature stays fine when running. it .... theengine manigement light is constantly on, but car running like a dream! ..... I have a 2007 astra sport hatch sxi 1.6 and seem to have a strange ...

Holden Astra known issues? - Holden - Automotive - Whirlpool

forums.whirlpool.net.au > Automotive > Holden

WhirlpoolDec 12, 2012 - The TS Holden Astras, late 90s to early 2000s, stay away. Unreliable ...People give the TS Astra a lot of flak but its a superb car. We have one ...

Jan 20, 2016 | Cars & Trucks

1 Answer

Brake pedal goes to floor when engine running but is fine when engine off


bleed the brakes again starting at the longest line at the rear and work forward . The indication is still air in the lines.

Feb 05, 2015 | 2002 Saturn SC

1 Answer

Hi every one I have a astra 1.9 cdti sri x pack 5 door I'm started to here sqweeking noise from the driver side front wheel when I turn right.when I turn left all fine just right When I touch the...


did you put a new rattle plate in between the new pads and pistion, also check the splash guard is not contacting the disc. needs to have a gap of 1cm from the disc.

Jul 02, 2017 | Cars & Trucks

1 Answer

How to change front brake pads on a 2000 jaguar s type? and if i pressed the piston in on a car with abs can that problem be fixed without buying a part? if not then what part will i need?


These are done just like any other disc brake system. Just slowly push the piston in and once the pads are installed, push the brake pedal half way down and do this until the pedal is hard again. Let me know if you need anything else.

May 19, 2010 | 2000 Jaguar S-Type

1 Answer

Suzuki Grand Vitara 1999:


Going by your description I think it could be something different, I would have the brake master cylinder checked, if you are suffering brake failure and shuddering it sounds like your callipers arent getting equal pressure when you apply the brakes. Or a freat lack of pressure to suffer brake failure. I hope this helps.

Nov 02, 2009 | 1999 Suzuki Vitara

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

2002 tahoe breaks lock up during driving


It sounds like the rear calipers are bad. Raise the rear wheels and see if you can turn the tires. If you can't, open the bleeder. If you still can't replace the caliper. If you can turn the wheel after you open the bleeder, replace the brake hose to that wheel.

Apr 12, 2009 | 2000 Chevrolet Silverado 1500

2 Answers

Changed front brake pads. brake pedal goes to floor. no brakes


Something doesn't sound right, you shouldn't have to remove the brake line to install pads. Did you have to do this on both sides? Do the new pads and the old pads look the same? Did you get the caliper on crooked? Just recheck your work first before replacing more parts. When you install the caliper, You have to hook the pad on one side first before you slide it over the rotor.

Mar 26, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Brake problems


Thank you for allowing me to assist you, Before we do anyhing, I need some additional information.
Please respond to the following 5 questions so that I may be able to help you better.
Is you vehicle front disc/rear drum or front disc/rear disc?
When were the brakes changed last?
If so, front or rear?
If you apply the park brake, does the vehicle move at all when you put it in gear?
Finally, I am understanding that the brake pedal goes to the floor, you have no resistance on the pedal, and the vehicle does not stop when applying the brakes. Da?

Oct 08, 2008 | 1991 Toyota Previa

Not finding what you are looking for?
2006 GMC Sierra Logo

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top GMC Experts

yadayada
yadayada

Level 3 Expert

75797 Answers

Freddy

Level 3 Expert

1311 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Are you a GMC Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...