Question about 2002 Volkswagen Beetle Turbo S

1 Answer

Another question, is the drain plug for the oil pan under the skid plate so i can change the oil myself? 2002 VW bug 2.0 motor Thanks, Matt

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 4,102 Answers

Hi, yes you need to remove this plastic skid plate then this will give you access to the oil drain plug.

Let me know how you get on or if you need further assistance ok

Posted on Feb 01, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What is the right oil and filter to use on the range2007 hse?


How To Change Oil and Oil Filter on Range Rover Sport or Land Rover LR3

  • Place an oil drain pan below the oil filter and drain plug and unscrew the oil filter.
  • Lubricate the rubber seal with clean oil and install the new filter. Tighten to 13 foot-pound torque.
  • Remove drain plug in the oil pan and drain the oil. Catch the oil in the drain pan. After draining the oil install and tighten the drain plug to 18 foot-pound torque.
  • Fill engine with 5W-30 weight oil. The 4.4 V8 takes 8 quarts; the 4.0 V6 takes 6 quarts. Start engine and check for leaks.
  • Recheck level and top up as necessary.
  • Reinstall the under engine shields / skid plates.

Apr 12, 2015 | Land Rover Range Rover Cars & Trucks

1 Answer

How do i change my oil?


Remove filler cap,
lift car
then from under the car remove oil pan drain plug.
Allow oil to drain into an oil waste pan.
Change oil filter also ..located under skid plate..use filter wrench to remove filter. Be careful as filter is full of oil ..drain in waste pan
wipe filter mounting plate clean..put a thin coating of oil on new filter gasket before spinning it on to the mounting plate..hand tighten and then tighten about 3/4 more turn.. reinstall drain plug. do not over tighten or you can strip the threads. Install correct viscosity and amount of oil start engine. let run to get pressure up. shut off engine, check level with dipstick and close cap....you are done.

Feb 12, 2015 | 2010 Nissan Frontier

1 Answer

How to replace oil pan


5.2 liter V8 engine?

Remove the four front skid-plate bolts holding the front skid plate, using a ratchet and socket. Remove the skid plate.

Pull the plastic splash shield away from the vehicle, loosening the retaining clips. Remove the splash shield.


  • Place an oil drain container under the oil pan. Loosen the drain fitting with a wrench until oil drains from the pan. When oil is done draining, tighten the drain fitting.

  • Disconnect the electrical connections running to the starter motor. Remove the starter motor mounting bolts with a ratchet and socket, then remove the starter motor.
  • Remove the oxygen sensor socket from the exhaust pipe, using a wrench.
  • Remove the exhaust manifold bolts where the exhaust meets the manifold on both sides, using a ratchet and socket
  • Place an jack under the transmission to support it. Remove the pressure on the transmission crossmember.

  • Remove the bolts that hold the transmission crossmember in place, using a ratchet and socket. Then remove the crossmember. Place a jack stand under the transmission to keep the transmission from falling off the jack if hit. Once removed, the exhaust will hang down, allowing enough room to remove the oil pan.
  • Disconnect the oil level sensor and the nut retaining the transmission cooling lines, using a wrench.
  • Remove the oil pan bolts with a ratchet and socket, then remove the oil pan and gasket.
  • Clean the mounting surfaces of the new oil pan and engine block. Make sure what ever you use to clean the surfaces dosn't gouge the metal.
  • Place a coat of RTV (gasket) sealer on the engine block where the pan will meet the rear main cap.
  • Place the new gasket on the pan and push the new oil pan into place. Finger tighten the oil pan mounting bolts to hold it in place. Tighten the bolts with a torque wrench to 18 ft-lbs. DO NOT OVER TIGHTEN THE BOLTS! Doing so will cause the gasket to deform and create leaks!

  • Connect the oil level sensor and the nut retaining the transmission cooling lines, using a wrench.
  • Place the exhaust back into position and replace the transmission crossmember bolts and crossmember with a ratchet and socket.
  • Remove the jack supporting the transmission.
  • Connect the exhaust back to both sides of the manifold, tightening the bolts with a torque wrench to 20 ft-lbs.
  • Attach the oxygen sensor socket to the exhaust pipe with a wrench.

  • Replace the starter motor by installing the starter motor mounting bolts with a ratchet and socket. Connect the electrical connections to the starter motor that were disconnected during removal.
  • Push the retaining clips on the plastic splash shield into the appropriate retaining clip holes.
  • Replace the front skid plate by replacing the four front skid plate bolts with a ratchet and socket.
  • Fill the engine with 5 quarts of oil. Make sure to check the level on the dipstick to find the exact level when filling.


  • Jun 28, 2012 | 1997 Jeep Grand Cherokee

    2 Answers

    I'd like to do an oil change on my trailblazer 04' but i cant find the drain plug,,,,where is it? Is there a guard i have to remove?


    Hello,

    The drain plug of the chevrolet 2004 trial blazer is located under the engine skid plate it is with the oil filter. And there is a guard to be removed. There is a trap door before it.

    The skid plate door is located by the drivers side door, directly midway underneath the vehicle. You will need a flat/phillips hear screwdriver to open the trap door. Do not worry, the screws are 'loss-proff' and will not fall off the trap door plate. Once this has been removed, the oil drain plug and oil filter are now visible and accessible.

    Oil change should not take you more that 15/20 minutes.

    Hope this helped.
    Take care and good luck

    Jan 03, 2011 | 2004 Chevrolet TrailBlazer

    1 Answer

    Can't find oil drain plug on my 2003 kia sorento


    it is located under the skid plate under the engine. there are two screws in the front under the radiator, two on the side, and two under the transmission. Once you take the plate off you will see the oil pan and plug

    Nov 14, 2010 | 2003 Kia Sorento

    1 Answer

    Is the oil pan drain plug located under the ground skid plate on a 3.5 trooper 4x4 2002. Is there a drain plug on the automatic transmission same vehicle or is it a sealed transmission?


    Hi

    Do you know which gearbox it is? some are GM and some BMW I know that sounds crazy but this model has 2 types of gearbox neither made by Izusi. Look here at this diagram tell me if that is the correct box http://www.unofficialbmw.com/images/BMW_Automatic_4L30E.pdf

    get back to me if not and I will be able to locate for you.

    Regards
    Dan

    Jul 22, 2010 | 2002 Isuzu Trooper

    1 Answer

    Where is the oil drain location on isuzu axiom


    Engine oil drain plug is on the bottom of the oil pan, To access it, you have to remove the front skid plate. Uses a 10mm socket and ratchet, and is not difficult to do.

    Nov 09, 2009 | 2002 Isuzu Axiom

    2 Answers

    2001 audi a4


    Transmision oil for 2001 Audi A4 1.8 l turbo:
    Manual gearbox (5 speed):
    - Capacity = 2,25 liters
    - Specification: Gear oil SAE 75 W 90 (synthetic oil)
    Part number G 052 145 S2 (1 liter)
    - To check oil level, unscrew oil filler plug placed on the left side of the gearbox in front and near of transmission axle, using an Allen 17 mm key.
    - Check oil level with locally manufactured tool, e.g. a piece of angled wire.
    - Specification: oil level 7 mm below bottom edge of oil filler hole.
    - Install oil filler plug, tightening torque = 25 Nm.
    Please Rate my Response! Thanks!

    Sep 27, 2009 | 2004 Audi A4

    Not finding what you are looking for?
    2002 Volkswagen Beetle Turbo S Logo

    Related Topics:

    151 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Volkswagen Experts

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22095 Answers

    yadayada
    yadayada

    Level 3 Expert

    75005 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    7710 Answers

    Are you a Volkswagen Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...