Question about 1990 Nissan Minivan

Open Question

I need to find out the td27 cylinder head torque settings for a 1992 Nissan Caravan Van.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

c17hydro
  • 2984 Answers

SOURCE: cylinder head torque settings 1990 2.6L isuzu motor

From front to back is this:


7 3 1 5 9



8 4 2 6 10



First torque value is 58 ft lbs.....then final torgue is 72 ft lbs.

Posted on Mar 21, 2009

  • 383 Answers

SOURCE: replacement of a head gasket on 2.5 liter nissan altima 2002

frajogag: First off, be aware that these bolts are "torque to yield" bolts (streach bolts). What this means is that instead of torqueing the head bolts to a specific torque specification, they are torqued down to a set spec and then tightened by rotating the bolts a certain angle, like 90 degrees. and all of them are turned the same amount.
This means that the shanks of the bolts must be checked to make sure they are not too thin (or the bolt has already stretched beyond limits and is prone to snap if used)
Here is how you check the bolts. Measure the bolt using a micrometer, at the base, or within the first 13mm from the end where it threads in. Then go to about 10mm before the threads end heading toward the top of the bolt. There should not be more than a 0.23mm (.0091 inch) or less difference or the bolt should be discarded.
Torque the bolts down to 98.1Nm ( 72.ft lb)
Looking at the head from the side, so you are looking at the full length from side to side, I will number the head bolts in this fashion.
#1 & 2 are directly in front of you and in the center of the cylinder head crossing it width wise.
#3&4 are to the left of #1&2, / #5&6 are to the right of #1&2
#7&8 are to the left of #3&4 / #9$10 are to the right of #5&6
Now, you have the sequence.
After the initial pull, back off all the bolts in the same sequence and then retorque them to 36 Nm ( 28 ft lb)
Using a torque angle wrench or having the ability to accurately judge turning angles. Rotate (clockwise) to a 75 degree angle. do this to all the bolts using the sequence I had provided.
Rotate the bolts (clockwise) 75 degrees again on all bolts in the same sequence. The proceedure is complete!

Posted on Apr 23, 2009

  • 8 Answers

SOURCE: need cylinder head bolts torque settings for nissan 3.2d

what nissan model do you need the head torques for

Posted on May 01, 2009

NismoMaster
  • 146 Answers

SOURCE: torque settings for cylinder head nissan sentra

Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Posted on Jul 26, 2009

  • 88 Answers

SOURCE: Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36

BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Posted on Aug 29, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Authomatic nissan terrano model 2006 td27


You will need to have the transmission removed to access the torque converter. A new torque converter should fix things unless debris from the damage has spread throughout the trans, in which case a strip down of the trans is the way to go...or a new/secondhand trans is installed.......

Mar 29, 2014 | 2005 Nissan Terrano 2.7

1 Answer

Cylinder head torque settings for a Nissan KA24E engine


54 - 61 foot pounds of torque. Be sure to follow the tightening sequence!

Dec 25, 2013 | Nissan Cars & Trucks

1 Answer

Final torque settings for nissan navara d22 diesel engine cylinder head


You do not need to re-torque modern cylinder heads. That went out withe Buffalo.

Nov 07, 2012 | Nissan Cars & Trucks

1 Answer

TORQUE SETTINGS FOR CYLINDER HEAD ON TD27


not sure what engine this is but if its a diesel cargo or serena with a cast iron head no turbo then around 80lbs ,if a smaller petrol engine with a alloy head then about 60lbs ,personally i never use a torque wrench i do it by experiance and feel ,like feeling for the bolt stretch if this sounds right but ?? you have to do plenty of them to know

Apr 04, 2012 | Nissan Nissan Cars & Trucks

2 Answers

ENGINE SPECS FOR NISSAN TD27 ENGINE


need head bolt torque setting for nissan td27 deisel engine been checking pots after she reved out and couldnt be turned off turns out if sump gets overfilled the engine will **** oil from sump and rev out ntill it explodes lucky we managed bto stop ours

Apr 08, 2011 | Nissan Pickup Cars & Trucks

1 Answer

What is the valve clearance and head bolt torque on a nissan td27 engine 1996 model


valve clearance is .014 inch for intake and exhaust with engine warm.
head torque it 21 ftlbs, then 44 ftlbs, then loosen all, torque to 89 inchlbs, then to 21ftlbs, then mark and turn the bolts an additional 60 to 65 degrees.
cyl head sub bolts torque 80 to 100 inchlbs.
thanks.

Jan 13, 2011 | 1990 Nissan Hardbody King Cab

3 Answers

Torque settings for cylinder head nissan sentra


Tighten in sequence to 29ft.lbs then tighten in sequence to 58ft lbs. then loosen all bolts. Then tighten in sequence to 33ft lbs. then tighten each bolt in sequence 90 degrees then tighten each bolt again 90 degrees

Jul 18, 2009 | 1999 Nissan Sentra

3 Answers

Hi I'm looking for cylinder head torque settings for a 1992 BMW 316/318 e36


BMW cylinder torque setting all models

According to my service manual as follows.

Cyl head to engine block (torx e12 M10 bolts)

Stage 1 30nm (22 ft – lb)
Stage 2 + 90 degrees
Stage 3 + 90 degrees

Cyl head to lower timing chain cover 10nm (89in – lb)

The tightening sequence is from inside to outside crossover as normal. Loosening sequence is from outside to inside crossover. Remember to set torque wrench at low setting and work gradually up through the whole sequence until you get the desired torque.

Jun 16, 2008 | 1992 BMW 3 Series

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

292 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

705 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...