Question about 2001 Chevrolet Blazer

Open Question

Replace broken headlight adjustment screw on 2001 Chevy Blazer

Recently I had a headlight burn out on my 2001 Chevy Blazer so I decided that maybe I would be able to replace it myself. I sucessfully replaced the bulb but when I was turning the adjustment screws to put the headlight back into it's orginal position and finish the job, the adjustment screw snapped in half. Now my headlight does not aim straight. I was wondering how to remove the broken screw and install a new adjustment screw for the headlight so I will be able to make it aim straight again.

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 10 Answers

SOURCE: Electrical low-beam headlight wire on 02 Chevy Trailblazer burnt

Get yourself to a junkyard and pack yourself a light lunch while you're at it. Take a leisurely stroll through the junk that closely resembles the one you need parts for. Go to the closest wiring harness to the headlight assembly, take your time and don't go trying to **** it, and unplug it from the bulbs up front. Make a simple and straight forward swap and do take the time to stop and smell the junkers, it's quite relaxing! Then, you should seriously make sure your new wiring harness is properly grounded (!), which I suspect to have been a contribing factor to your problem of overheating the bulb socket. Do take the time to go over the stuff that should be grounded and make it so. Th e job is quite simple and well worth you taking the time to do it yourself.

Posted on May 27, 2009

  • 2 Answers

SOURCE: headlight alignment

I ran into this same issue about 2 months ago. Had to replace the bulb and for the life of me I could not get it back in right. Kept aimed very high and hitting the hood. Had to go in and pay the dealer to fix and aim it. This is the first vehicle I have ever owned where I have been unable to change my own lightbulbs.

Posted on Sep 12, 2008

  • 1 Answer

SOURCE: how to replace low beam headlight bulb on 1999 chevy malibu

just have a philip screw driver, remove the screw, pull out the light and take the light to the nearst aurozone and they will give you the right light, and put it back the same way.

Posted on Dec 30, 2008

emissionwiz
  • 75822 Answers

SOURCE: 2001 Chevy S-10 Headlight bulb replacement?

There are two tabs that hold the Headlight assembly in place. Pull one up, then holding the Headlight assembly, pull the other one up. Locate the light that is burned out. Remove the harness from the light, then twist the light to remove. Replace with new one, and reverse process. Be careful to not touch the glass of the new bulb. The oil from your fingers and hands will shorten the life of the bulb

Posted on Mar 11, 2009

  • 832 Answers

SOURCE: replace headlight bulbs on a 2000 chevy blazer LT.

Yes, you can. Just take off the front grill, and the
headlights assembly. Don't tinker with the head-
light assembly adjusting nut, as this would change your headlight level. Take headlight bulb
off and change it. Replace the headlight, then, the
grill, and it's done.

Posted on Sep 21, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I have a 2001 chevy malibu which had to replace front bumper and now i need to adjust the headlights. On my brights tye left headlight shines upward really high and the right one shines to the left not as...


There are 2 screws on EACH headlight. One Screw does UP and DOWN and the other does LEFT/RIGHT.

These are normally an E Socket to adjust on a Chevy. there are some models taht use a Phillips Screwdriver Head to do the adjustments

Apr 06, 2013 | Cars & Trucks

1 Answer

I have a 2001 Chevy blazer windows don't work rear


If windows are electric, check switch and replace if needed.
Check window motors wiring connections. If motors are bas, replace as needed.
If manual, window could be off track or cranking mechanism may be broken. Replace as needed.
If light fuses are good, replace bulbs to the lights.

Jan 21, 2013 | Cars & Trucks

1 Answer

How do you adjust the headlights on a 2000 model Chevy Silverado 2500HD


Raise the hood and look for two small screws on the headlight, one is closer to the radiator for side to side adjustment and the other is for up and down adjustment.

Jul 28, 2010 | 2001 Chevrolet Silverado 2500HD

1 Answer

Head lights want come on my 2001 chevy blazer S10


Check headlight fuses and relays.Two locations possible.End of dash on Dr.side and relays maybe under the hood to thr rear of batterie on Dr.side.

Feb 05, 2010 | 2001 Chevrolet Blazer

1 Answer

How do i remove the dash of a 2001 chevy blazer to replace a heater core?


big job maybe you should buy a manual for that blazer, also label everything, the steering colum and every thing has to be removed before dash can be removed, good luck.

Oct 09, 2009 | 2001 Chevrolet Blazer

2 Answers

How do you adjust the headlights on a 1997 chevy blazer (S-10) 4WD.


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Sep 29, 2009 | 1997 Chevrolet Blazer

1 Answer

Replace headlight bulbs on a 2000 chevy blazer LT.


Yes, you can. Just take off the front grill, and the
headlights assembly. Don't tinker with the head-
light assembly adjusting nut, as this would change your headlight level. Take headlight bulb
off and change it. Replace the headlight, then, the
grill, and it's done.

Sep 21, 2009 | 2000 Chevrolet Blazer

2 Answers

How to adjust headlights on 1995 chevy blazer


The adjustment screws/nuts should be located either on the top of the headlamp assembly, behind the headlamp assembly, or near the frame rail by the radiator support.

You will have vertical adjustment screws for each independent beam (separate highs and separate lows, but will be same screw if highs and lows are the same bulb). You may also have additional horizontal adjustment screws as well

Park your car on a level ground 30 feet from a wall and measure the height from the ground to the bulb and mark on a wall (do this for highs beams and low beams if the bulbs are separate, if highs and lows are the same bulb, only do it for the lows)

For Low Beams: If the headlights read VOR, then aim the brightest part or cutoff part just below the mark on the wall. If it says VOL or nothing, aim them 2 inches below the mark on the wall.

For High Beams (if separate from low beams): Aim the headlight directly at the line you marked on the wall.

Jul 05, 2009 | 2000 Chevrolet Blazer

1 Answer

2001 Chevy S-10 Headlight bulb replacement?


There are two tabs that hold the Headlight assembly in place. Pull one up, then holding the Headlight assembly, pull the other one up. Locate the light that is burned out. Remove the harness from the light, then twist the light to remove. Replace with new one, and reverse process. Be careful to not touch the glass of the new bulb. The oil from your fingers and hands will shorten the life of the bulb

Mar 11, 2009 | 2001 Chevrolet S-10

1 Answer

How to adjust headlights on 1995 chevy blazer


park the truck about 10 feet from a wall. I have allways liked to use a garage door.now pop the hood .on each headlight. there is a screw to move up and down left and right.

Mar 07, 2009 | 2000 Chevrolet Blazer

Not finding what you are looking for?
2001 Chevrolet Blazer Logo

Related Topics:

405 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8195 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...