Question about Ford F-150

1 Answer

I will put 4by4 and does not work - F-150 Ford Cars & Trucks

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 396 Answers

You didn't specify if this is electric or lever activated. . If electric,,, The transfer case Motor nees replaced.

Posted on Feb 01, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

How does the 4x4 work in a 93 z71?

Stop your truck put transmission on neutral change level on your 4by4 on low or hi gear than put transmission on drive there you are ..

Jul 24, 2014 | 1993 Chevrolet K1500

1 Answer

When turning left or right and in backing (reversing) my ford explorere 2002 make a loud noise under and the tires jack some how, all check under do not show grinding or rubbing part and my battery run...

You have bad front drive axle CV Joints

Need to replace worn axle

You know the electrical circuit that has the
problem, since you removed the fuse

Now you need a wiring diagram or a repair shop

Jun 23, 2011 | Ford Explorer Cars & Trucks

1 Answer

2002 chey trailblazer 4by4 light on the swich stay on 2 wheel drive if i put into 4 wheel drive or all wheel drive and one light flash on where ever i put the swich on. feels like is goes in 4 wheel high...

The Transfer Case Control Module (TCCM) in this model year have been known to hang up, try pulling fuse #48 (4WD) in the rear fuse panel located under the left rear seat. Reinstall fuse and see if everything works OK, if not, you probably need to replace the TCCM.

Dec 07, 2010 | 2003 Chevrolet TrailBlazer

1 Answer

I would like to get a download of the 5speed trany so i can take it apart and put back together it a 93 4by4 it froze up setting out of truck would like to clean it up and get working again ,is there...

Check out faxonautoliterature. They list a manual specific to rebuilding that transmission that should do the trick. I've used them before and had excellent service. Hope this helps.

Dec 13, 2009 | 1993 GMC Sierra K1500

1 Answer

Can i take a 1992 full size blazer body and put it on a 1992 full size chevy 4by4 short bed frame?

If memory serves frame length on a CK10703 is about 121" and on the Blazer is about 111".

Can it be done? Anything can be done, depending upon how much work you'd like to do and how much money you want to spend.

Nov 28, 2009 | 1992 Chevrolet C1500

1 Answer

Why does my 2000 jimmy keeping trying to go in to 4lo

i had the same thing happen to me i put a new 4by4 switch and it fixed the problem

Oct 27, 2009 | 2000 GMC Jimmy

1 Answer

Hi i have a 04 cheve silverodo 2500hd 4by4 with a abs.problem

there is a ABS module or proportioning valve that could be a culprit. those do have an ABS diagnostics port that a good shop should be able to scan and tell u what is wrong.

Oct 22, 2009 | 2000 Chevrolet 2500

1 Answer

2000 mazda 4by4 problem

Do you know that you have to put the truck in N then put in 4X4 then put in gear.. do the same thing to take out.. I am sure you knew that but just in case you do not.. hope it helps

Jan 19, 2009 | 2000 Mazda Pickup Troy Lee Cab Plus 4

1 Answer

Stwitch problems

I recently had a similar problem but mine would not come out of the ignition. I took it to the shop and they had to replace the steering column. This is was a costly part to put in.

Dec 16, 2008 | 2000 GMC Jimmy

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

23 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts


Level 3 Expert

78289 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers


Level 3 Expert

5655 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides