Question about Toyota Matrix

Open Question

Rear jack points for 2004 Matrix

Where are the jack points for the back of the Matrix? I want to jack up the back and put stands under it so I can remove both rear wheels.

Posted by on

5 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 30 Answers

SOURCE: where are the jacking points on the hyundi accent

http://econtent.autozone.com:24991/znetrgs/repair_guide_content/en_us/images//0900c152/80/07/33/62//medium/0900c15280073362.gif

this shows jacking points.

Posted on Sep 30, 2008

  • 4369 Answers

SOURCE: rear wheel bearing

SECTION 205-02B: Rear Drive Axle/Differential — Ford 8.8-Inch Ring Gear 2003 Mustang Workshop Manual IN-VEHICLE REPAIR Axle Shaft Removal

  1. Raise and support the vehicle. For additional information, refer to Section 100-02 .
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the rear brake disc (2C026). For additional information, refer to Section 206-04 .
  1. Remove the differential housing cover (4033) and drain the lubricant. For additional information, refer to Differential Housing Cover in this section.
  1. Remove the differential pinion shaft (4211).
    1. Remove the differential pinion shaft lock bolt (4241).
    1. Remove the differential pinion shaft.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Remove the U-washer (4N237).
    1. Push the axle shafts (4234) inboard.
    1. Remove the U-washer.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Damage to the rear brake anti-lock sensor (2C190) may occur if it is not removed before the axle shaft.
    Carefully remove the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Remove the axle shaft.
--------------------------------------------------------------------------------------
Rear Wheel Bearing and Axle Shaft Oil Seal Removal
  1. Remove the axle shaft (4234). For additional information, refer to Axle Shaft in this section.
  1. NOTE: If the wheel bearing oil seal is leaking, the axle housing vent may be plugged.
    Using the special tools, remove the rear wheel bearing and wheel bearing oil seal.
Installation
  1. Lubricate the new rear wheel bearing with the specified lubricant.
  1. Using the special tools, install the new rear wheel bearing.
  1. Lubricate the lip of the new wheel bearing oil seal.
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. Using the special tools, install the new wheel bearing oil seal.
  1. Install the axle shaft. For additional information, refer to Axle Shaft in this section.

-------------------------------------------------------------------
Installation
  1. Lubricate the lip of the wheel bearing oil seal
    • Use Premium Long-Life Grease XG-1-C or equivalent meeting Ford specification ESA-M1C75-B.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the wheel bearing oil seal.
    Install the two axle shafts.
  1. s3b~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not damage the rubber O-ring in the axle shaft groove.
    Install the U-washer.
    1. Position the two U-washers on the button end of the axle shaft.
    1. Pull the axle shaft outward.
  1. NOTE: If a new pinion shaft lock bolt is unavailable, coat the threads with Threadlock and Sealer EOAZ-19554-AA or equivalent meeting Ford specification WSK-M2G351-A5 prior to installation.
    Install the differential pinion shaft.
    1. Align the hole in the differential pinion shaft with the case lock bolt hole.
    1. Install a new differential pinion shaft lock bolt.
  1. Install the differential housing cover and fill the rear axle with the specified lubrication. For additional information, refer to Differential Housing Cover in this section.
  1. Install the rear brake anti-lock sensor. For additional information, refer to Section 206-09A .
  1. Install the rear brakes. For additional information, refer to Section 206-04 .
  1. Install the tire and wheel assembly. For additional information, refer to Section 204-04 .
  1. Lower the vehicle.

Posted on Apr 10, 2009

ghost45
  • 1280 Answers

SOURCE: how to remove brake drum rear wheel 2004 Hyundai Elantra

Jack up rear of car till tire is off the ground.
Remove lug nuts & remove wheel.
Remove phillips screw(s) from drum.
Using a hammer, strike the drum to loosen it from the hub.
Remove drum by simutaneously turning it and pulling it outward away from the vehicle.

Posted on Oct 04, 2009

  • 115 Answers

SOURCE: rear axle removal on a 2004 f150 fx4

First thing is to make sure you chock the front tires so the truck will not roll. Raise the rear end and set it on jack stands. Put the transmission in Neutral and make sure the parking brake is off. Remove the rear tires and disassemble the brakes on the side with the leaking seal. Place a drain pan under the rear differential and remove the cover. Remove the differential shaft lock bolt. You will need to turn the drive shaft by hand to access the bolt. It will be on the right side off the spider gear housing. Only use a 5/16 or 8mm 6 point box end wrench to remove the bolt. After you remove the bolt reach on the top of the spider gear housing and push the differential lock shaft down to remove it. Make sure the spider gears do not rotate after you remove the shaft. If they do you will need to realign everything to reinstall the lock shaft. Push the axle shaft in enough to remove the "C" clip from the tip of it. The axle will now slide out of the rear end. You can use the tip of the axle shaft to remove the axle seal. If you're changing the bearing as well you will need a slide hammer with axle bearing adapters to remove it. You can use a socket and hammer to install the new bearing and seal. Be careful not to damage the bearing and seal. I recommend packing grease in the back side of the seal. This helps prevent the spring on the seal lip from coming off. Assembly is the reverse. Clean off all the gear oil from the differential cover and the axle. You can use RTV as a gasket if the OEM gasket is damaged. Fill the rear end with new gear oil of the proper type. Refer to your owner's manual.

Posted on Jun 05, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

I would like to change the brake pads on my 2010 Kia Rio.But I'm having a hard time figuring out where to put the jack to jack it up, and then where to put the jack stands....


After you jack the vehicle up put your jack stands under the joint where the rear control arm hinges under the body. this link will show you where the jack goes. Kia Rio Lift And Support Points

Apr 30, 2017 | Kia Cars & Trucks

Tip

Replace brake pads on rear of car


  • First, you have to get a ratchet set. You may also need some everyday tools that you should have lying around the house. You also need a trolley jack and a car stand to go under your car to stop it from falling off of the jack.
  • After you have gathered the supplies, loosen the bolts to the rear left wheel with a 17mm ratchet. Do not fully remove the bolts, but loosen them enough. After loosening, find the jack point under the car near where the wheel is. Place the stand under the jack point and jack up the car then place the car stand under the jack point at the side of the trolley jack then remove the trolley jack slowly letting the car rest on the stand. Do the same thing on the other read wheel so that the entire back is lifted slightly making it easier to work with both wheels.
  • Now remove the wheel bolts completely and remove the wheels. Locate the two 15mm bolts on the back of the brake caliper, just under the caliper holder. Remove them and liberally apply force on the caliper to get it out of the way. It’s a good idea to rest the caliper on the trolley jack to prevent you from bending any of the break pipes.
  • Once the caliper is removed, take out the brake pads and replace them with the new ones. Place the caliper back and place the bolts back in the correct position from the start and tighten fully. Place the wheel back on the car hub and tighten the bolts. The bolts won’t be able to be tightened fully since the car is still suspended. Repeat this ending process on the other wheel. Only after, using the jack under the car stands, lower the car back to the ground. Once the car is back on the ground, use the 17mm socket to make sure each wheel is completely tightened.
  • When shopping for ratchets, try to find some that have long handles so it is easier to apply the force needed to tighten the wheels’ bolts completely.
  • Congratulations on changing your brake pads and saving money that would otherwise be spent at the garage.

on Jul 08, 2010 | Volkswagen Fox Cars & Trucks

1 Answer

How to remove rear axle from 2004 ba ford falcon


Hi there.
Well first jack up the rear end of car then block up the front wheels (front and rear) and put stands under the rear jacking points STILL keeping the pressure on the jack, clamp the rear brake pipe that comes from the body to the rear axle and clamp with a small clamp
but dont tighten to tight remove the flex pipe and also the rear shockers from the axle ,then the spring u bolts and then the hand brake cable from the center adjuster,now it should only leave your tail shaft 4 nuts/bolts.
But why are you removing the rear/axle????

May 04, 2014 | 2005 Ford Falcon

2 Answers

How to take a transmission out of a truck without it on a lift


There are car ramps that give enough clearance to be able to remove tranny from beneath vehicle. Most jack stands are too short for same. in the past I have had to do this, and with car not moving, required jacking truck up jjust to get ramps in place under tires. not fun but possible.

Sep 28, 2013 | Cars & Trucks

1 Answer

Where do i place a jack stand on a 1995 Jeep Grand Cherokee?


Hope this helps and please don't forget to rate...thanks!

Jacking points on all Jeep vehicles



c17hydro_1.gif

Your Jeep was supplied with a jack for emergency road repairs. This jack is fine for changing a flat tire or other short-term procedures not requiring you to go beneath the vehicle. Do not attempt to use the jack on any portions of the vehicle other than specified by the vehicle manufacturer. Always block the diagonally opposite wheel when using a jack.



c17hydro_2.gif

Placing a floor jack under the front frame rail



c17hydro_3.gif

Placing a floor jack under the rear frame rail at the leaf spring shackle. It may be necessary to place a block of wood between the frame rail and the jack



c17hydro_4.gif

Supporting the front of the vehicle with jack stands placed under each frame rail


A more convenient way of jacking is the use of a garage or floor jack. You may use the floor jack at the specified points in following the illustrations.

Never place the jack under the radiator, engine or transmission components. Severe and expensive damage will result when the jack is raised. Additionally, never jack under the floorpan or bodywork; the metal will deform



c17hydro_5.gif

Support the rear of the vehicle using jack stands placed underneath each side of the rear differential (inset photo)

Nov 04, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Jack points on 2004 Volvo S80 to change oil?


As always use extreme caution when lifting vehicle, but I have found that the easiest way to lift my car for oil change is to put jack under the cross member under engine.

Jan 20, 2010 | 2004 Volvo S60

1 Answer

The function that rsiaes and lowers the vehicle doesn't work,


Lifting

The following instructions must be carried out before raising the vehicle off the ground.

  • Use a solid level ground surface.
  • Apply hand brake.
  • Select 'P' on automatic gearbox selector.
Note: If the propeller shafts are to be removed, reference must be made to the relevant operation. To avoid damage occurring to the under body components of the vehicle the following jacking procedures must be adhered to.

DO NOT POSITION JACKS OR AXLE STANDS UNDER THE FOLLOWING COMPONENTS:
  • Body structure other than approved jacking points
  • Bumpers
  • Fuel lines
  • Fuel tank
  • Brake lines
  • Front or rear suspension arms
  • Transfer box
  • Steering linkage
  • Front or rear differential units
  • Engine sump
  • Automatic gearbox
NOTE: For certain repair operations, it may be necessary to support the engine under the sump. In this case, a block of hardwood or a rubber block should be positioned on the jack lifting cup to protect sump. Vehicle jack
The jack provided with the vehicle is only intended for use in an emergency, for changing a tyre. DO NOT use the jack for any other purpose. Refer to Owner's Handbook for vehicle jack location points and procedure. Never work under a vehicle supported solely by the vehicle jack.

Hydraulic jack
A hydraulic jack with a minimum 1500 kg, (3,300 lbs) load capacity must be used.

WARNING: Do not commence work on the underside of the vehicle until suitable axle stands have been placed in their correct position. Always chock the wheels when jacking. The handbrake may be ineffective when the wheels are off the ground. Raising and supporting the vehicle
To assist in raising the vehicle, jacking points are provided as shown in the following illustrations.

Raising the front of the vehicle
Apply handbrake, select 'P' on automatic gearbox selector and chock rear wheels.
Axle stand positions - front

Raise vehicle to enable axle stands to be positioned under, either, the front sub-frame, or the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.
Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack.
Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Raising the rear of the vehicle
Select 'P' on automatic gearbox selector and chock front wheels.

WARNING: Always chock the front wheels when jacking the rear of the vehicle.

Axle stand positions - rear

Raise rear of vehicle to enable axle stands to be positioned under the rear sub-frame. Alternatively, the axle stands may be positioned under, either, the recommended customer jacking points or the front mounting points of the rear sub-frame.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging the body / component. If any damage occurs to the washers on the front mounting points of the rear sub-frame, then the washers must be replaced. Carefully lower jack until vehicle sits securely on axle stands.

WARNING: Always support the vehicle on axle stands when using a jack. Before commencing work on underside of vehicle re-check security of vehicle on stands.

Reverse procedure when removing vehicle from stands.

Wheel-free lift
The following warning must be read before attempting to lift the vehicle.

WARNING: The vehicle cannot be supported safely in a wheel-free condition using the wheel-free facility of a four post ramp, and under no circumstances must this method be employedA wheel free condition may only be achieved on a four post ramp by raising each end of the vehicle and positioning axle stands beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between each axle stand and the jacking point to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox. WARNING: The front and rear suspension lower arms must NOT be used as lifting / jacking points. Alternatively, support the vehicle on an approved two post lift with the arms of the lift beneath the recommended customer jacking points.

CAUTION: Place a piece of hardwood or a rubber block between the lifting equipment and the jacking points to avoid damaging any components. If the propeller shafts are to be removed, select NEUTRAL in the main gearbox.

Oct 04, 2009 | 2003 Land Rover Range Rover

1 Answer

1995 n pug 306 td. how to change back axle mounts.


remove the rear box off the exhaust(2x13mm nuts)prop the front wheels then jack the back end of the car up put the jack on the tube of the axle use 2x axle stands on the rear jacking points on the sills lower the car on to the stands(leav the jack under the rear axle to help lower it to the ground) then release the hand brake.now in side the boot of the car you will find 3x16mm nuts on the left side and the same on the drivers side there are some times plastic gromits covering the nuts undo the nuts and lower the jack wala the axle is off.DO NOT FORGET TO UNDO THE BRAKE PIPES.the rest is simple.i have done this job by my self many times.

Jul 07, 2009 | 1991 Peugeot 405

1 Answer

2004 tiburon : front jacking points?


The official front jacking points are on the reinforced edge of the unit body, just behind the front wheels.

If you're using a hydraulic jack, you can jack the front of the car from the front tow hook, place your axle stands under the front jack points, then let the car down onto the axle stands.

Always use axle stands when working on your car, never trust the jack alone.

Jul 05, 2009 | 2004 Hyundai Tiburon

1 Answer

How to change oil in 04 toyota matrix


Go to Walmart buy four quarts of oil it will say in the owners manuel what to get, a oil filter the store will have a book to look up the car know the engine size and model,a filter wrench, a drain pan and a jack to carefully jack up the front area of the passenger side of the car . I use a old rag and double fold it so the jack dosent mess up the jack point of the car. It will tell you also in the owners manuel where to jack it. PLEASE do not use the factory jack to go under the car buy one. OR go to the dealer and ask for a oil change coupon or go to Goodyear .

Sep 30, 2008 | 2004 Toyota Matrix

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

675 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...