Question about 1999 Mazda B-Series

1 Answer

Replace a 1999 b2500 control arm , i dont know how to seperate from the pin end

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 454 Answers

They make a special tool to press the ball joint (pin) out of the back of the wheel hub. I use a prybar and hammer. Position the prybar under the frame in such a way that you can apply downward pressure on the control arm. The bolt should still be installed holding the control arm to the frame. While applying as much downward pressure as possible on the prybar, hit the ball joint housing on the wheel hub with the hammer sharply and repeatedly until the ball joint falls free. I know it sounds terrible to hit your truck with a hammer, but you are not going to hurt it.

Posted on Jan 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What r problems to be on the look out for on a 1999 chevy malibu with the 3100 v6 in it and there is a rattle when i hit bumps or rough road the struts are fine


Broken stabalizer links, broken stabilizer bar, and worn out stabilizer bar bushings are fairly common. As well as the rear bushings on the front lower control arms. A quick inspection of the front end and you should be able to tell if the links are bad, bar is broken, or the lower control arm bushings are separated. If the rear bushings on the front lower control arms are seperated the lower control arm will look like it is resting on the subframe.

Oct 19, 2010 | 1999 Chevrolet Malibu

2 Answers

Ball joint problem


you can do it either way, but special tools are needed, pay a shop to replace them and have it aligned

Jun 12, 2010 | 2000 Ford Expedition

1 Answer

Replace lower ball joint


pull lowerball joint pin. seperate with pickle fork. remove the 2 lower control arm bolts. remove lower control arm.

reverse to install. yes the entire lower control arm must be replaced

May 20, 2010 | 1998 Ford Windstar

1 Answer

How to change the pittman arm and idler arm on a 1999 S10 Chevy Blazer 4x4?


Pitman arm requires a pitman arm puller, and a tie rod seperator or "pickle fork". Remove the cotter pin on from the joint on the pitman arm and center link, then remove the nuts from both ends of pitman arm. Use the pitman arm puller to remove the pitman arm from the steering gear, then use the tie rod seperator to remove the end from the center link. Reinstall and retighten nuts, do not leave out the cotter pin.
Idler arm will require tie rod seperator. Remove the cotter pin from the end at the center link, use the tie rod seperator to seperate the joint there. Unbolt the idler arm from the frame, and remove. On reinstalling remember to install a new cotter pin. It would be best to have the front end alignment checked after replacing these parts.

Apr 08, 2010 | 1999 Chevrolet S-10 Pickup

1 Answer

Need to know if 1999 mazda b2500 has a transponder


if the head of the key is made of black plastic covering it is

Feb 06, 2010 | 1999 Mazda Pickup

1 Answer

I need yo know how to replace the cv joint and


remove axle nut,seperate balljoint from control arm,usually a good whack with a hammer on the control arm near the balljoint will free it,pry control arm down to remove knuckle assy, remove roll pin from inner axle joint now you can remove axle,most of the time the inner joint boot tears this is called the d-o-j {double offset joint} replace this boot as well,my suggestion is consider replacing axle with reman depending on mileage 100k or more.remember when reinstalling axle splines need to be lined up on inner shaft so roll pin goes in without problem good luck

Jul 18, 2009 | 2001 Subaru Forester

1 Answer

Lower control arm replacement


lower control arm replacement is 0w/coil front springs isnot as tough as it looks. Just have the car high enough th get a floor jack under the control arm and be able to lower it at least six inches. Remove the shock,undo the bolts at the frame and lower the jack untul the spring can be removed. once spring is out, use a picke fork to seperate the lowe ball joint, you nooe have the control arm free. rememver to put the rubber pads on each end of the coil spring on reassembly or a sqeek will develop. new cotter pins an lube ball joints Good luck

Jul 08, 2009 | 2006 Chevrolet Malibu

5 Answers

I need to replace upper right ball joint, 98 honda civic


This is a pretty easy job.The way i do it is take the two 14mm bolts louse from the strut on the inner fender well,then take the 17mm bolt out of the bottom of the strut on the lower control arm this will make it drop down.Then take the 14mm bolt louse that fastens the ball joint to the spindle take a hammer and hit the upper spindle and it all will come apart.Now you will have the two bolts that holds the upper control arm in place these are 17mm bolts drop the strut down and remove the upper control arm now you can go in with the new one.Hope this helps !!!

Mar 19, 2009 | 1998 Honda Civic

2 Answers

Replacing Ball Joints on 2001 Mazda B2500 (upper and lower)


its easier to get the whole control arm and the lower one has to be pressed in. it is not and easy job if you dont have the right tools checkout rockauto.com to look at the replacement parts and to get a price on them

Jan 07, 2009 | 2001 Mazda B-Series

1 Answer

2000 Expedition Right Ball Joint


you have to get a ball joint seperator, remove the retaing pin, and then the nut, put the seperator between the ball joint and the mount, use a hammer and hit the end of the seperator with the hammer, this will pop it loose, then take a large crow bar and push down on the control arm, this will free it from the arm... use a drill with a 1/2" bit to drill the rivets out of the top of the ball joint....

the new ball joint with come with nuts and bolts to bolt the new one down....

slide the ball joint back into the arm, and put the nut on and tighten as much as you can, then replace the retaining pin.....

Jun 14, 2008 | 2000 Ford Expedition

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

143 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...