Question about 2004 Mazda RX-8

Open Question

MAF sensor diagram? 2004 RX8

MAF sensor diagram?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 1861 Answers

SOURCE: MAF Sensor 2004 Dodge Stratus

If your car has a MAF (Mass Air Flow) sensor, it would be located in the air delivery tube that runs from the air filter box to the throttle plate assembly on the intake manifold. It will have a wiring connector going to it, also. The MAF does exactly what it is called: It "senses" the volume, or "mass" of the air-flow; thusly it needs to be in the intake air tube. If you do NOT have such a device in the air-tube, you have a MAP sensor, (Manifold Absolute Pressure); this is another way of measuring the same air volume, albeit older technology. You will commonly find this device on the firewall, with a vacuum line running to the intake manifold.

I hope that this sheds some light on your question.

Thanks for choosing FixYa for advice!

Posted on Mar 06, 2009

  • 7353 Answers

SOURCE: 2004 Kia Amanti. Does not hold idle. Smoke and gas

Dont trust a wrecker driver. theres a reason they tow cars and not work on them. have a qualified shop check it and recommend repairs. you dont want to waste money guessing.

Posted on Oct 02, 2009

  • 347 Answers

SOURCE: Where is the coolant temprature sensor locating on

it is normally located on the engine block near the radiator hose.

Posted on Oct 03, 2009

melvi_99
  • 387 Answers

SOURCE: I need a wire diagram that shows were all 5 wires

i hope that this will help you, cdf6d0c.tif

Posted on Sep 05, 2010

taran_2005
  • 10515 Answers

SOURCE: 2004 F250 5.4L 6 pin

Hi,

Most of the models have the similar wiring. Check the one i have for 01 F250 and let me know :-

http://www.allfordmustangs.com/forums/attachments/v6-talk/24292d1172198458-need-wiring-diagram-maf-iat-6-pin-connector-2001maf.gif

Let me know,if needed further assistance.

Hope i helped you.

Thanks for using ' Fixya ' and have a nice day!!

Posted on Sep 26, 2010

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Rx8 engine sputter


Try cleaning your MAF sensor. Its on your air intake box held down by 2 screws. Can use MAF cleaning spray or electrical contact cleaner. e8e0082a-ebe4-49c3-9d91-dd3d16ae0387.jpg

Mar 20, 2013 | 2004 Mazda RX-8

1 Answer

Location of maf sensor on jaguar x type 2004


DON'T USE WD40 on the air intake this will destroy the Lambda sensors,
for info on the location go here http://www.bluejag.co.uk/X-Type-MAF-Sensor.php

Oct 04, 2012 | 2003 Jaguar X-Type

1 Answer

The mazda rx8 is hard starting and not idling properly. How do u set the timing for the rotas. Do u have a diagram


there are no timing on the rotors for a wankel engine. The timing is controlled by a computer for the RX-8. The sensors & distributors can be adjusted on the RX7's & other Mazdas but I know that there were major engine changes to the RX-8 so I can't tell you for sure. I use to have an RX-7 and worked on it all the time.

Aug 03, 2012 | 2004 Mazda RX-8

1 Answer

How do I repair my 2004 Monte Carlo as supercharged kicking out codes p102 and p171


you can try this:

Verify that the Mass Air Flow Sensor wiring is connected properly and that there are no broken / frayed wires.

Inspect for any air leaks near the MAF sensor.

Take the MAF out and clean it using a spray cleaner such as brake cleaner or electrical contact cleaner. Be gentle with the sensor.

Check the voltage of the MAF sensor (refer to a repair manual for vehicle specific information)

Replace the MAF sensor.

Sep 20, 2011 | 2004 Chevrolet Monte Carlo

2 Answers

Hi there, please can you help? I have a 2005 231bhp Rx8 thats not running properly. It is displaying fault code PO410, and the car will not rev, little better when cold but really struggles to get over...


CODE PO410 IS SECONDARY AIR INJECTION SYSTEM PROBLEM. POSSIBLE CAUSES AIR SYSTEM MALFUNCTION. RESTRICTED OR DAMAGED IN THE EXHAUST SYSTEM. RESTRICTED IN THREE WAY CATALYTIC CONVERTER.PCM MALFUNCTION.

May 05, 2011 | 2004 Mazda RX-8

2 Answers

Where is the map sensor located on a 2004 rodeo


check the right side of the intake manifold or the right rear of the intake manifold...

Feb 03, 2010 | 2004 Isuzu Rodeo

1 Answer

Where is the coolant temprature sensor locating on


it is normally located on the engine block near the radiator hose.

Sep 30, 2009 | 2004 Mazda RX-8

2 Answers

The power steering went out on my buddies 04 Mazda RX8 where is it located


this car has electric sterring rack.lots of sensors and relays

Mar 11, 2009 | 2004 Mazda RX-8

1 Answer

2004 mazda mpv geting fault code p0 174 .what should the problem be???


It means that you've got a too lean (too much oxygen) condition in the exhaust. It may only be a dirty MAF (mass airflow) sensor. Are you running an "oiled-type"air filter such as a K&N? This can contribute to a dirty MAF sensor. HERE is a diagram to help you out. Good luck.

Nov 20, 2008 | Mazda MPV Cars & Trucks

Not finding what you are looking for?
2004 Mazda RX-8 Logo

Related Topics:

639 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mazda Experts

yadayada
yadayada

Level 3 Expert

75744 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22114 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8123 Answers

Are you a Mazda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...