Question about 1993 Ford Ranger SuperCab

1 Answer

I need to know what u use to remove the driveshaft from a 93 ford ranger

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 194 Answers

Make sure you block the wheels and apply the e brake. it only takes the right size wrench on the back by the axle then pull it out of the transmision if you dont plug the end of your tranny all the fluid will run out

Posted on Feb 05, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
  • 3 Answers

SOURCE: 2005 ford ranger 4wd front driveshaft

NO when in 2wd the front tires will not turn. I have the same truck

Posted on Apr 15, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Trouble shoot turn signals 1994 Ford Ranger 2.3 engine


Diane, There are 2 separate flashers on your vehicle, one is for the emergency/4 way lights and one flasher is for the signal lights. It may be worth the couple bucks and replacing the signal flasher as a first step. Recheck bulbs/sockets, fuses/relays, flasher. If all looks good possible signal switch is bad. Remove switch and try to clean contacts or replace switch. Check the attached links,instruction and guides, Good luck
"I hope this helped you out, if so let me know by pressing the helpful button. Check out some of my other posts if you need more tips and info."
https://ca.answers.yahoo.com/question/index?qid=20090405174036AARb2Uc
1994 Ford Ranger Turn Signal Electrical Problem 1994 Ford Ranger
93 Ranger Turn Signal Problem Ford Truck Enthusiasts Forums

Aug 20, 2016 | 1994 Ford Ranger Supercab

1 Answer

I need to know how to get the hex nut out of my 1993 ford Ranger pickup-rear end ??


Caution!!! Removing the driveshaft yoke retaining nut could cause misalignment of the ring and pinion gears and lead to more serious problems. If you are wanting to access the pinion bearing because your 8.8 rear end has started making noise then you really need to disassemble the unit as a whole. A job left in most cases to an expert.

Apr 10, 2011 | 1993 Ford Ranger SuperCab

1 Answer

Changing clutch on a 2003 ford ranger how do I


Well to start, you need to remove the shifter from the transmission. Then remove the driveshaft. Then unplug the plugs from the side of the transmission and disconnect the clutch fluid line. Then remove the crossmember. Unbolt the bellhousing bolts. Then have a friend help you remove the transmission. Then unbolt the clutch.

Jul 09, 2010 | 2003 Ford Ranger Regular Cab

2 Answers

How to change the oil pump of a ford ranger 1993


You didn't post your engine size so please pick the one that works for you....I'll post them all separately:

2.3L Engine The oil pumps are not serviceable. If defective, they must be replaced.
  1. Follow the service procedures under Oil Pan Removal and remove the oil pan assembly.
  2. Remove the oil pick-up and tube assembly from the pump.
  3. Remove the oil pump retainer bolts and remove the oil pump.
To install:
  1. Prime the oil pump with clean engine oil by filling either the inlet or outlet port with clean engine oil. Rotate the pump shaft to distribute the oil within the pump body.
  2. Install the pump and tighten the mounting bolts to 14-21 ft. lbs. (19-29 Nm)

WARNING Do not force the oil pump if it does not seat readily. The oil pump driveshaft may be misaligned with the distributor or shaft assembly. If the pump is tightened down with the driveshaft misaligned, damage to the pump could occur. To align, rotate the intermediate driveshaft into a new position.


  1. Install the oil pick-up and tube assembly to the pump. If there is a gasket between the pump and the pick-up, use a new gasket when installing.
  2. Install the oil pan as previously described.

e4df20b.gif

Jan 19, 2010 | 1993 Ford Ranger SuperCab

1 Answer

Master cylinder removal 93 ford ranger


lay some old rags under it before you remove it or get old turkey baseter that you will never use again and drain it out that way have a countainer ready.Note fluid and baseter no longer fit for use!

Dec 23, 2009 | 1993 Ford Ranger SuperCab

1 Answer

Need to know will a 3.0 v6 out of a 93 fit in my


you will need to change engine and transmission along with the engine wiring harness and computer also if your 2.3 was carburetorated you will need the fuel pump out of the fuel tank .
also remove the engine frame mounts and the transmission cross-member from the 93 might also need changed.

Nov 11, 2009 | 1986 Ford Ranger 2WD

1 Answer

Ring gear


You already know the axle is 4.10 gears. How did you determine that? Are you just wondering how many teeth the ring gear has? There are 3 ways to figure the ratio, 1st the tag, which is missing, 2nd mark the bottom of the tire, and mark the driveshaft, move the car forward and count the driveshaft rotations in one complete tire rotation, this determines the ratio, which in your case would be 4.10 turns of the driveshaft in one wheel rotation. 3rd would be to count the teeth on the ring and pinion, divide to get 4.10, or whatever it comes out to.

Aug 15, 2009 | 1999 Ford Ranger SuperCab

1 Answer

2005 ford ranger 4wd front driveshaft


NO when in 2wd the front tires will not turn. I have the same truck

Mar 24, 2009 | 2005 Ford Ranger

2 Answers

I paid for an answer about my 89 ford ranger drive shaft and did not get one. Can I get my money back or do I need to contact Pay-Pal??


To replace the centre bearing you first remove driveshaft from vehicle.
Pull the shaft apart at the middle universal joint.
On the back of the section that has the centre bearing you will see a nut that holds the uni ears onto the shaft.
Undo the nut and remove the ears. Then press the centre bearing off the shaft and reassemble with new one.
Hope this is more helpful.

Jan 01, 2009 | 1991 Ford Ranger Supercab

Not finding what you are looking for?
1993 Ford Ranger SuperCab Logo

Related Topics:

56 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22258 Answers

fordexpert

Level 3 Expert

5572 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...