Question about 1990 Nissan 300ZX

1 Answer

I have a 1991 nissan 300zx 5spd manual wont start i have full power in the dash i have check the clutch pedal for the safety switch and little activation button all is ok can you help

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Scholar:

    An expert who has written 20 answers of more than 400 characters.

  • Expert
  • 70 Answers

Check the starter solenoid and the starter connections. if either of them burned up the car wouldnt start.... wait... is it turning over or no? if not then check your power transistor unit on the passenger side timing cover. could also cause it to not start..

Posted on Feb 01, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
New users get to try the service completely Free afterwhich it costs $6 per call and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

1985 nissan 300zx has start signal failure how do you repair the problem


Start signal comes from the clutch engagement switch. When you press the clutch the pedal arm hits a switch and signals the motor to be able to start. Look and see if you have a little rubber piece pushed through a hole on the clutch pedal arm

Mar 18, 2013 | 1985 Nissan 300ZX

1 Answer

Whats the problem when the truck wont start and i tap the clutch slave cylinder and it does start? but then that wont work anymore. what do i do? smugman697@yahoo.com


I'd take a look up near where clutch pedal pivots for a switch similar to brake light switch, that has to be depressed or released by pedal when pushed. Probably a safety feature to insure vehicle won't start unless clutch in, just in case it's in gear. May be adjustable, but if not, or adjustment doesn't help, replace it.

Jan 11, 2011 | 1991 Nissan Pickup

1 Answer

Where is the brake light switch on a 1991 300zx


I would guess it its located under the dash near the top of the brake pedal assembly.

May 28, 2010 | 1991 Nissan 300ZX

1 Answer

91 300zx N/A 5spd power loss and engine chatter


i had same thing and my cataletic converter was plugged. red hot . after it cooled i could start it and only crawl home.and check timing belt.and battery cablesneed to be clean and vasilene for good connection no corrosion ,no green on any connections. if.check engine lite on do self diagnostic. info on internet nissan ecm codes

May 01, 2010 | 1991 Nissan 300ZX

1 Answer

I have a 1992 nissan 300zx and i just installed a new clutch master cylinder and a new clutch slave. i'm tring to get the pedal to get firm so i can bleed it and get a full pedal,but when the pedal gets a...


you need to bleed the cluch slave cylinder located on the transmission and the clutch operating cylinder located in the passenger front hood compartment next to the power steering resivoir

Mar 30, 2010 | 1992 Nissan 300ZX

1 Answer

I have a 1990 Nissan 300zx 5spd manual wont start i don't have power in the dash and i replaced the battery and it still wont start unless i jump it can you help?


if it starts when you jump it and have a new battery, the altanator is your next step....next time you jump it, leave it run with the lights and accesories on, take off the cables, is it kills the altanator is not doing its job.

Mar 21, 2010 | 1990 Nissan 300ZX

1 Answer

I have a 1992 nissan 300zx and i just installed a new clutch master cylinder and a new clutch slave. i'm tring to get the pedal to get firm so i can bleed it and get a full pedal,but when the pedal gets a...


Try using 2 people , get the person inside to press the pedal and you undo the bleed valve a little, tighten the valve and get them to release the pedal (or pull it up if it is a little stiff) keep going untill no more air is expelled.

Nov 15, 2009 | 1992 Nissan 300ZX

1 Answer

90-96 Nissan 300zx auto/5spd starter the same?


The starter should fit either an automatic or manual.

Jun 27, 2009 | 1991 Nissan 300ZX

2 Answers

Neutral safety switch....I think


The switch is located at the top of the clutch pedal assembly, above your feet. Its a little cramped, but its a simple dc two wire switch, you should be able to check it with a meter for power and to see if the switch does indeed need replacement. If thats the problem, when you see the new switch, you'll know it goes in, very easy. good luck

Aug 12, 2008 | 1988 Ford F 150

Not finding what you are looking for?
1990 Nissan 300ZX Logo

Related Topics:

318 people viewed this question

Ask a Question

Usually answered in minutes!

Top Nissan Experts

yadayada
yadayada

Level 3 Expert

76630 Answers

Phil Lovisek
Phil Lovisek

Level 3 Expert

726 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22219 Answers

Are you a Nissan Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...