Question about 1999 Honda CR-V

1 Answer

My 2002 CR-V keyless remote quit working yesterday. When I tried the key it would not in the lock?? I was stranded and then finally I was able to unlock with the key. Today the keyless will lock all doors except the drivers side and key will still not fit in lock...I have no way of locking my car. Help!

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Vice President:

    An expert whose answer gotĀ voted for 100 times.

    Sniper:

    An expert who has posted more than 50 answers, of which 90% or more were rated as helpful.

  • Expert
  • 105 Answers

With the problem you are describing i would say you need to replace to drivers door lock actuator. or remove the door panel and see if a rod has popped off, or a clip broke holding the rod in place. actuators are somewhat of a pain to replace if you've never done one before. i've seen this exact problem many times and with a new door lock actuator you'll be all set.- hope this helps

Posted on Jan 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Key won't unlock driver door


the key or fob?
the key is bad,
use the spare key that came with all new cars.
always keep a spare. or get stranded.

Feb 22, 2014 | 2007 Honda CR-V

1 Answer

I replaced batteries in keyless remotes for 2002 chevrolet monte carlo ss. how do I resynchronize the keyless remotes?


Hello: To resynchronize the keyless entry close all doors, key out of ignition. Hold lock and unlock buttons till the doors (all) lock then unlock. If the transmitter still doesn't work you have other problems. Go to auto zone they can check your transmitter to see if it is working.

Oct 24, 2011 | 2002 Chevrolet Monte Carlo

1 Answer

Drivers door will not open with key or battery hand piece,,other doors okay with both. 2002 crv


-If the problem is that keyless remote does unlock or lock door, but the lock lever still move when pulling up and down by hand. Door still open and close with both inner and outer, then might the driver door lock actuator is bad. The actuator lock and unlock the door for you when using the keyless remote or door lock/unlock switch.

-if you try using the key to unlock door and the key doesn't turn the door cylinder, then you have a bad door lock cylinder.

-if the lock lever doesn't move up or down and you can't open door using any handle, then you got a bad lock latch assembly.

I'm not sure what the issue is but hope this helps you.

Jan 18, 2011 | 2002 Honda CR-V

1 Answer

I am not able to use the hand held lock/unlock now. The driver door lock tries to work, but it won't. If I push the lock down manually, it will lock all locks. What could be wrong?


Note:
Entering the programming mode cancels all learned keyless remotes, so none of the
previously programmed remotes will work. You must reprogram all of the keyless
remotes once you are in the programming mode. You must complete each step within 5 seconds of the previous step to keep the
system from exiting the programming mode.

1. Turn ignition switch to ON (II)
2. Press the LOCK or UNOCK button on one of the remotes. (An unprogrammed
remote can be used for this step.)

3. Turn ignition switch to LOCK (0)
4. Repeat steps 1, 2 and 3 two more times using the same keyless remote used
in step 2

5. Turn the ignition switch to ON (II)
6. Press the LOCK or UNLOCK button the same remote. Make sure the power door
locks cycle to confirm you are in programming mode.

7. Press the LOCK or UNLOCK button on each remote you want to program. Make
sure door locks cycle after you push each remote button to confirm system has
accepted the remote.

8. Turn the igniton switch to LOCK (0) to exit programming mode.
9. Test remote(s)

Mar 07, 2010 | 2002 Honda CR-V

1 Answer

Car alarm


dear friend- it appears that your remote lost it code if this is a factory system you can disconnect the battery for a while,but before you do that press the lock and unlock buttons similtanious if it does work disconnect the battery.reconnect and try again do not leave the key in the car when doing this.

Jul 05, 2009 | 2002 Nissan Altima

1 Answer

2003 Honda CR-V door lock switch does not work


try replacing the switch yourself the dealer could be lying to you to make some money

Jun 25, 2009 | 2002 Honda CR-V

1 Answer

Car won't start without keyless entry


Sounds like the anti-theft system isn't working. You might be able to get a bypass kit for your car. Check with an auto parts store.

Mar 13, 2017 | 1996 Pontiac Firebird

2 Answers

Keyless entry remote


Try this, it works on several 2002 models:


Step 1: Open drivers door and leave open.

Step 2: Lock and unlock the drivers door using the power door lock switch on the door.

Step 3: Insert key into the ignition.

Step 4: Turn key to on position and return to off position. (IMPORTANT - use ON position NOT ACC position). Do this 3 times within 10 seconds. Leave key in the ignition.

Step 5: Open and close the drivers door 3 times. (Door should be left open after this step).

Step 6: ECU should respond by locking and unlocking the doors.

Step 7: Press any button on remote #1. ECU responds by locking and unlocking the car doors.

Step 8: Press any button on remote #2 (etc.) Each time the ECU will respond by locking & unlocking the doors.

Step 9: Remove the key from the ignition and the ECU will respond a final time with a series of door locks and unlocks.

Jun 20, 2008 | 2002 Mazda Protege

Not finding what you are looking for?
1999 Honda CR-V Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Honda Experts

yadayada
yadayada

Level 3 Expert

75235 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7795 Answers

Are you a Honda Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...