Question about 2000 Jeep Grand Cherokee

1 Answer

How do i take out the oil pressure switch having trouble getting the plug off. 2000 grand jeep

Posted by on

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Hot-Shot:

    An expert who has answered 20 questions.

    Corporal:

    An expert that hasĀ over 10 points.

    Mayor:

    An expert whose answer gotĀ voted for 2 times.

  • Contributor
  • 31 Answers

Hi on the connector there is a safety lock you pull it to the side and then remove the connector then you will need a tube socket 26mm then remove the oil pressure switch

Posted on Jan 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2002 Jeep Grand Cherokee Limited P0846 code



Trouble Code: P0846

A/T 2/4 Pressure Switch Circuit Malfunction
Possible Causes:


2/4 pressure is incorrect, or internal transmission faults exist 2/4 pressure switch circuit is open, shorted to ground or power 2/4 pressure switch is damaged or it has failed TCM relay power circuit to L/R switch is open (loss of B+) PCM/TCM has failed

May 16, 2012 | 2000 Jeep Grand Cherokee

1 Answer

What is the correct oil pressure for 2000 grand jeep cherokee larado its about 75 now. i want to buy this car but worried about the oil pressure.


Normal oil pressure should be between 40 and 60 psi. A cold engine will normally have higher pressure. If you're seeing 75 psi on a warm engine I would recommend having the pressure checked with a manual gauge to verify the gauge in the Jeep is working correctly. If the gauge is correct oil viscosity may be too high (oil too thick) or there may be a problem with the oil pump pressure relief valve. If the gauge is not correct the sending unit may be at fault.

Apr 09, 2011 | 2000 Jeep Grand Cherokee

1 Answer

How to change oil pressure sending unit on jeep grand cherokee laredo 2000.


First things first do you have a repair manual? If you don't have one get one, Changing the unit is realitively simple, you just disconnect the battery, disconnect the oil pressure sending unit's electrical connector, remove the sending unit, now most sending units are small and look like a short chubby spark plug with an electrical blade connector on the end of it. simply use a wrench to loosin and remove and install by screwing in and tightening and reconnecting the electrical connecter then the battery and your as good as new!

Feb 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

2000 Jeep Grand Cherokee Limited oil pressure gauge is dropping to 0 when idling in gear. What is wrong and what do I have to do to ix it?


First check the oil level and top up as necessary. If the oil pressure is at 0 , then it would very quickly sieze the engine, that not being the case, it sounds like you need to replace the oil pressure switch/sensor, which will be mounted either on the engine block or on the oil filter housing. Hope this helps

Jan 21, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Where is the oil pressure sending unit located on a 2000 jeep grand cherokee 4.0 liter


Removal & Installation
  1. Disconnect the negative cable from the battery.
  2. Raise vehicle on hoist.
  3. Remove front splash shield.
  4. Disconnect oil pressure sender connector (4).
  5. Remove the pressure sender (2).
6eaedba.gif
Oil pressure sending unit


To install:
  1. Install oil pressure sender.
  2. Connect oil pressure sender wire.
  3. Install front splash shield.
  4. Lower vehicle.
  5. Connect the negative battery cable.

Jan 12, 2010 | 2000 Jeep Grand Cherokee

1 Answer

Oil pressure gage at 50


if pressure is higher than what it normally is after an oil change, you may have used the wrong grade of oil (too thick). Foam could be from overfilling, or from water in the oil (maybe antifreeze getting into the oil?).

Apr 01, 2009 | 2000 Jeep Grand Cherokee

1 Answer

2000 jeep grand cherokee


You definitely need to put a mechanical gauge on there and check for ACTUAL oil pressure. It is possible that the passageway to the sending unit may be plugged with gunk. If oil pressure is not correct or if in doubt, do not drive it 'till you know for sure what's going on in there. No noises tells me that it is likely not serious but an engine is just too expensive to gamble!!!

Feb 14, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Irradic reading at oil pressure guage


The sending unit would be the first thing to change, at least it would eliminate that.

Jan 25, 2009 | 2000 Jeep Grand Cherokee

1 Answer

Oil pressure gauge on my 2000 jeep is on


The most common problem is a bad oil pressure switch on the 99-02 grand cherokee with the 4.7l v8. The part has failed on 90% of all 99-02 grand cherokees I have worked on. The housing is junk,but since it has lasted longer then 36,000 miles the factory would not issue a recall. The oil pressure switch can be purchased at any outlet. but have found the duralast was decent. that being said Go to autozone and get part # PS471 (oil pressure switch for 1999-2002 N code 4.7L V8.) chances are if you encounter the same problem after replacement you will need to drop the oil pan and un clog the oil sump.

To replace the switch, under the hood look for the power steering pump on the driver side of the vehicle, to the right and under the p/s pump is the oil pressure switch, If it is wet, its bad for sure, remember to disconnect the battery before service,as not to harm the gauges.

Jul 22, 2008 | 2002 Jeep Grand Cherokee

Not finding what you are looking for?
2000 Jeep Grand Cherokee Logo

Related Topics:

94 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts

yadayada
yadayada

Level 3 Expert

75807 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22133 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8172 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...