Question about 1995 Jeep Grand Cherokee

1 Answer

95 jeep grand service 4x4 swich comesup on display whay does that mean

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 20 achievements.


    An expert that got 10 achievements.


    An expert that got 5 achievements.

  • Jeep Master
  • 17,970 Answers

According to the mechanic who works on Jeep, it's one of three things:
1) Corrosion on the connector to the switch (which is located on top of the transfer case).
2) A bad switch. Part cost about $22.00, or
3) A bad console display. he says they have had a fair number of console display units fail. That one runs about $240.

Hope helped.

Posted on Jan 31, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi there,
Save hours of searching online or wasting money on unnecessary repairs by talking to a 6YA Expert who can help you resolve this issue over the phone in a minute or two.

Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.

Here's a link to this great service

Good luck!

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

Wiring diagram grand cherokee jeep 1997

Specificaly, about whay wiring circuit diagram? We need the Service Manual of ZJ Grand Cherokee Series (1993-1998).

Keep us updated.

Jose ( ZJLImited )

Nov 03, 2011 | 1997 Jeep Grand Cherokee

1 Answer

I have parking sensors on my 2006 jeep grand cherokee front and back. they do not work any more. the computer is telling me to service them. how? I do have two red lights on the displays and i can't...

When you put your jeep into reverse you will see the red lights. These will still work even when is says service parking assist system needs service. The problem is in your transmission control unit. This is a common problem in the Grand Cherokees. You will have two options here. You can take it to your Jeep dealership and ask them to flash the TCU. This may or may not work. The other option is they will have to replace the TCU. They run about $600.00. Hopefully if they flash the TCU it will work again. Good luck

Oct 03, 2011 | 2006 Jeep Grand Cherokee

1 Answer

1995 4.0 4x4 jeep grand Cherokee Laredo blinking check engine code 38-55

Sorry I can't find a code 38 for '95 Jeeps in any of the data bases.
55 - End of codes

Jun 05, 2010 | 1995 Jeep Grand Cherokee

1 Answer

Service 4x4 switch what does that mean

it could simply mean change the oil, please put the key in the ignition and turn it forward not enouf to start it and then push down on the gas pedal 3 times all the way to the floor then wait 5 seconds and turn the key in the off position and then start vechile, this should reset that service light. for futher help please call 419 689 1114 and i will be happy to assist you.

Apr 24, 2010 | 1994 Jeep Grand Cherokee

1 Answer

How difficult is it to change a heater core?

yes, you gotta remove the dash,not too bad if your a jeep tech

Oct 07, 2009 | 1995 Jeep Grand Cherokee

2 Answers

Where is the location of the oil pressure sending unit on a 2000 jeep grand cherokee 4x4

Someone comments say...

- On my 95 4.0 it's right beside the distributor.
- The sensor is on the passenger side of the engine, back near the firewall.

Good luck!!

Jul 14, 2009 | 2000 Jeep Grand Cherokee

1 Answer

4x4 switch on my 95 jeep grand needs replaced and i can not find it

Are you referring to the switch in the vehicle or on your transfer case/transmission housing?

Jul 12, 2009 | 1995 Jeep Grand Cherokee

3 Answers

'93 Jeep Gr. Cherokee 4x4 switch warning

this switch does not switch the vehicle from 2 wheel to 4 wheel drive. Grand cherokee have a manual shifter for that. The 4x4 switch is on top of the transfer case and tells the driver information display what 4 wheel drive mode the Jeep is in. ex..if you have selectrac, in 2 wheel the rear wheels on the display will light up, in 4 wheel all 4 wheels will light up, in 4 wheel low it will have the word low lit up in yellow. This is the only purpose for this switch and a bad one will not affect the functioning of the 4 wheel drive. Check out and a new one can be purchased for about 35 dollars. If you call the dealership and ask for a 4 wheel drive switch, they will have no clue what you are talking about. The actual name is " 4WD indicator light switch"

Feb 22, 2009 | 1999 Jeep Grand Cherokee

1 Answer


Front wheel bearings can be done at home rear wheel bearings will require a hydraulic press and an axle puller. Either job can be difficult depending on amount of rust and availability of tools. The front wheel bearings are an assembly and once the jeep is up on jack stands, with the tires, brake calipers, and rotors removed, it is only a matter of removing the axle nut and 3 bolts (which can be difficult depending on rust) holding in the old bearing assembly

Feb 22, 2009 | 1995 Jeep Grand Cherokee

2 Answers

94 Jeep Grand Cherokee Transmission Problom

1994 is the same as 1997. parts are interchangeable

Dec 31, 2008 | 1994 Jeep Grand Cherokee

Not finding what you are looking for?
1995 Jeep Grand Cherokee Logo

Related Topics:

147 people viewed this question

Ask a Question

Usually answered in minutes!

Top Jeep Experts


Level 3 Expert

80608 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22326 Answers

Kevin Daniels

Level 3 Expert

1455 Answers

Are you a Jeep Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides