Question about 1995 Ford Ranger Supercab

1 Answer

Trouble code on 1995 ford ranger 3.0 egr flow

I have a trouble code for egr malfunction i replaced the egr valve and it didn't fix it. there is a miss when the engine is under load when driving. Any ideas?

Posted by on

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 105 Answers

You have an intake leak

Posted on Jan 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2003 ford expedition engine light code po401 .


From the looks of my research, it sounds like you have an EGR flow insufficient malfunction. This could be a circuit problem, a plugged port, a defective EGR valve or solenoid. You need to get a good flow chart if you are intending on trouble shooting this yourself, along with a digital volt ohm meter.

May 17, 2016 | Ford Cars & Trucks

2 Answers

99 maxima ran till it was parked now it turns over will not start gave code p0400 any ideas


The fault is somewhere around the EGR valve - probably the EGR valve or the throttle position sensor.

Before replacing any sensors try removing and cleaning the EGR.

Here's a Youtube link that may be of help to you:

1999 maxima egr Google Search

This link explains about the EGR:
P0400 Exhaust Gas Recirculation Flow Malfunction

CEL code P0400 EGR Flow Malfunction

Mar 27, 2016 | Cars & Trucks

5 Answers

ENGINE RUNS FINE. SERVICE LIGHT IS ON AND THE CODE NUMBER SHOWING IS PO401. WHAT IS THIS FOR SAYING?


  1. po401 refers to an insuffient flow of EGR gasses
  2. locate egr valve
  3. with engine running at idle
  4. on the underside of the valve you can access the diaphram.
  5. wearing glove if ness
  6. lift diaphram while idling
  7. does engine stall or run very rough?
  8. if not remove valve
  9. start engine
  10. you should hear a very large vaccum leak and exhaust noise
  11. if either are missing investigate cause
  12. if ok reassemble.
  13. locate DPFE sensor
  14. inspect sensor for damage
  15. inspect hose to sensor for damage
  16. replace sensor
  17. 9ecffd7.gif

Aug 10, 2010 | 1999 Ford Taurus

1 Answer

2002 FORD RANGER 6CYL. 4.0L I GOT A P1400 TROUBLE


Exhaust gas recirculation flow insufficient detected.
Maybe you got a bad DPFE sensor, or the pintel inside the egr valve is not opening all the way causing the insufficient flow.

May 14, 2010 | 2002 Ford Ranger Regular Cab

2 Answers

98 ford ranger 4.0L runs very rough when mass air flow sensor is plugged in. runs, but still a little rough but drivable when unplugged. tried new sensor, still the same. any ideas?


did you try cleaning the idle control valve and the egr valve out with carb cleaner.try that before replacing any parts,also if there is any codes in the system those should also lead you in the right direction.

Oct 27, 2009 | 1998 Ford Ranger SuperCab

1 Answer

1995 ford ranger Xlt it idles like its missing but when i put in drive and drive off its fine i tried injector cleaners ran higher octane did wires plugs cap/rotor cheacked all the leads im hoping its a...


they have egr issues that cause that they also have valve issues that could cause that! i have replaced a few injector here and there also so i would start there and then go to the egr valve! and so on...

Sep 18, 2009 | 1995 Ford Ranger Supercab

1 Answer

1995 mercury villager check engine code p1200 injector open


P0400 = EGR Flow
P0325 = knock sensor (Do not ever change a knock sensor, they don't affect anything and cost $600 to replace for absolutely no gain)
P1200 = I can't find this one. I think it's injector flow
report back on what you find.
Egr flow may be plugged egr passages or a bad solenoid.
--------------
1996 PCED OBDII-Villager SECTION 1B: Description and Operation
Exhaust Gas Recirculation System
Exhaust Gas Recirculation (EGR) System Operation The exhaust gas recirculation (EGR) system (Figure 1 below) recirculates a portion of the exhaust gases into the intake manifold under average vehicle driving conditions to reduce combustion temperatures and exhaust gas NOx content. The amount of exhaust gas recirculated varies according to operating conditions and will be cut completely under:
  • Engine starting condition
  • Low engine coolant temperature condition
  • Excessively high engine coolant temperature condition
  • Engine idling condition
  • High engine speed condition
  • Mass air flow sensor failure
The exhaust gas recirculation (EGR) system on the Villager uses the exhaust gas recirculation/evaporative emission (EGR/EVAP) control solenoid valve to provide vacuum to both the EGR valve and the EVAP canister when commanded by the PCM. If the exhaust backpressure is sufficient to close the EGR backpressure transducer valve, vacuum is sent to the EGR valve and allows EGR gas to flow into the intake manifold. If the exhaust backpressure is not sufficient, the EGR backpressure transducer will remain open and allow vacuum from the EGR/EVAP control solenoid to vent to the atmosphere.
The EGR system monitor, for OBD II regulations, uses an EGR temperature sensor to monitor the EGR system. The EGR temperature sensor is a thermister located in the EGR passageway. When hot exhaust gas is recirculated into the engine, the temperature at the EGR passageway increases. This increase is sensed by the EGR temperature sensor and a signal is sent to the PCM to indicate EGR flow. If the EGR temperature sensor does not detect EGR flow when commanded by the PCM after two consecutive drive cycles, the malfunction indicator lamp (MIL) will be illuminated and a diagnostic trouble code (DTC) will be stored. The MIL will be turned off after three consecutive drive cycles are completed with no malfunctions detected. The DTC will remain stored in the PCM memory until 80 drive cycles have been completed without the same malfunction detected in the system.
Figure 1: Exhaust Gas Recirculation (EGR) System Diagram Item Number Description 1 — EGR/EVAP Control Solenoid 2 — Air Cleaner Housing 3 — Throttle Valve 4 — EGR Temperature Sensor 5 — EGR Valve 6 — EGR Backpressure Transducer 7 — EVAP Canister
Exhaust Gas Recirculation (EGR) Backpressure Transducer Valve The exhaust gas recirculation (EGR) backpressure transducer valve is used to control EGR. The EGR valve is operated by ported vacuum, but the ported vacuum will normally be vented off at the EGR backpressure transducer valve. As rpm increases, exhaust pressure increases and pushes on the diaphragm in the EGR backpressure transducer valve and closes the vacuum vent.
Figure 2: EGR Backpressure Transducer Value
Item Number Description 1 — Throttle Valve 2 — Vacuum Port 3 9D475 EGR Valve 4 9F452 EGR Backpressure Transducer Valve 5 — EVAP Canister 6 — EGR/EVAP Control Solenoid 7 — Vent
EGR/EVAP Control Solenoid The exhaust gas recirculation/evaporative emission (EGR/EVAP) control solenoid (Figure 3) is controlled by the powertrain control module (PCM). The EGR/EVAP control solenoid controls vacuum to both the exhaust gas recirculation (EGR) valve and to the evaporative (EVAP) emission canister. When the EGR/EVAP control solenoid is off (12 V signal from the PCM) vacuum is supplied to both the EGR valve and to the EVAP canister. When the EGR/EVAP control solenoid is on (ground supplied by PCM) vacuum is vented to the atmosphere keeping the EGR valve closed and no vacuum to the EVAP canister. The PCM will command the EGR/EVAP control solenoid on at:
  • Engine starting condition
  • Low engine coolant temperature condition
  • Excessively high engine coolant temperature condition
  • Engine idling condition
  • High engine speed condition
  • Mass air flow sensor failure
Figure 3: Exhaust Gas Recirculation/Evaporative Emission (EGR/EVAP) Control Solenoid
Exhaust Gas Recirculation (EGR) Temperature Sensor
The exhaust gas recirculation (EGR) temperature sensor (Figure 4) is a thermister type sensor that monitors the temperature of the exhaust in the EGR passageway. As the EGR flow increases, the temperature increases. This process creates a change in the resistance of the sensor, which decreases as the temperature increases. The signal is sent to the powertrain control module (PCM) to indicate that the EGR system is working properly. If the EGR temperature sensor does not change resistance as the PCM expects on two consecutive drives, the malfunction indicator lamp (MIL) will be illuminated and a diagnostic trouble code (DTC) will be stored.
Figure 4: EGR Temperature Sensor Exhaust Gas Recirculation (EGR) Valve
The exhaust gas recirculation (EGR) valve (Figure 5) recirculates portions of the exhaust gas back into the intake manifold to reduce the amount of the NOx released during combustion and to reduce combustion temperature. The amount of exhaust gases that are released into the engine is proportional to the load on the engine.
Figure 5: EGR Valve

Mar 20, 2009 | 1995 Mercury Villager

1 Answer

1992 ford ranger 2.3 liter engine


on code 328 Replace the EGR valve. and code 332 Replace the EGR valve man !

Aug 09, 2008 | 1992 Ford Ranger

1 Answer

Ob2 code p14444


P1444 Purge Flow Sensor circuit Input Low
Evaporative emmision control system control valve malfunction
You can find all the fault codes here:
http://www.ford-trucks.com/article/idx/0/247/article/Ford_OBDII_Diagnostic_Trouble_Codes__P1000P1999__Codes_Specific_to_Ford_vehicles.html

Jul 24, 2008 | 1995 Ford Ranger Supercab

1 Answer

1995 Ford Ranger ( engine light ) and stuff need help plz


if your obd2 scanner fits the connection you have obd2, obd1 connector is way differnt.

your code p1443
Control System
Canister Purge
Valve (Mechanical)
Malfunction
Monitors the fuel vapor
flow between the
engine intake manifold
and the EVAP
canister. The system
failure occurs when a
leak or blockage
between the intake
manifold, the EVAP
canister purge valve
and the EVAP canister
is detected by the
PCM.
l Pinched, blocked or
plugged fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister
l Disconnected, cracked
or cut fuel vapor
tubes/hoses (except
between fuel tank and
EVAP canister)
l Damaged EVAP
canister purge valve
Check for audible vacuum
noise in the engine
compartment or significant
fuel odor in the engine
compartment or near the
EVAP canister.

This link has all the codes you need.
http://rockledge.home.comcast.net/~rockledge/RangerPictureGallery/DTCs.pdf

Jul 17, 2008 | 1995 Ford Ranger Supercab

Not finding what you are looking for?
1995 Ford Ranger Supercab Logo

Related Topics:

234 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

fordexpert

Level 3 Expert

5481 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...