Question about 2008 Pontiac G6 Sedan

1 Answer

Windshield wiper arm

The wind shield wiper arm ball join snapped. i took the nut off the top of the blade arms but they still dont come off how do u get them to come off

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 474 Answers

You need to get a tool for that job or you can gently pry undernieth it with a small prybar reinstall the nut flush to the top of the stud and try to tap on it while prying it should pop off.remember be gentle it is pressed on and you do not want to ruin the threads to hold the arm unless you are replacing that as well.

Posted on Jan 31, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

Windshield wiper one stop moving on my 97 grand prix


Hello, you'll will need to remove wiper motor crouling to get the wiper motor. There will be two rods attached to the wiper motor. Now, this arms operate the wipers on your auto wind shield.
One of the arms have came loose from it ball joint. GB....stewbison

Sep 24, 2011 | 2002 Pontiac Grand Prix

3 Answers

Wind shield wiper arm does not hold blade tight against window


WIPER ARM SPRING BROKEN.YOU HAVE TO REPLACE WIPER ARM.I DONT THINK YOU CAN BUY REPLACEMENT SPRING INSIDE THE ARM BUT YOU CAN ASK.BUT I THINK THE WHOLE WIPER ARM HAS TO BE REPLACED.

Jun 23, 2011 | 2000 Mercury Grand Marquis

2 Answers

Wind shield wiper on pax side has stopped working. It just swings free. What could be wrong and how do I access it?


it has come disconnect or stripped out from the motor. it needs to be reconnected if it came apart if stripped apart the arm to the wiper needs to be replace. the teeth have warn away. open the hood there is a cover that is over the wipers. remove to see motor for wipers to see the problem

Nov 30, 2010 | 2004 Oldsmobile Alero

1 Answer

Wind shield wipper handle wont stay in place it broke how do you fix it


Hi there,

Well you can please follow the below steps -
1. Lift the wiper arm away from the windshield. If the tension spring is damaged or broken, the arm will not show resistance. If it is functioning properly, then pull the arm back until the hinge locks in a vertical position.
2. Remove the retaining nut at the base of the windshield wiper arm and pull the wiper arm off.
3. Slide the new wiper arm assembly on.
4. Tighten the retaining nut and lower the arm back down to the windshield.
Please post comments for any other help or information......

Good Luck!!

Thanks

Mar 26, 2010 | 1999 Chevrolet Silverado 1500

1 Answer

Replacing windshield wiper motor


Remove the wiper arms. Take out the screws that hold down the wind shield cowl. Unplug the wiper motor (center driver's side) by pulling out the red clip on it and squeezing the tab. (Mark which arm came off which side) remove the 13mm nut from the wiper motor idler arm and take out the 3 10mm bolts that hold it in.

Feb 23, 2010 | 1998 Plymouth Voyager

1 Answer

2004 grand prix driver side wind shield wiper going past windshield and now is not in sync with other wiper arm,and still moves past windshield and jams up.


The arm is stripped onto the stud its pressed into which is call a wiper transmission. That part mounts to eack ww blade then to the wiper motor. You need a new transmission and maybe a new wiper are as well

Jan 20, 2010 | 2004 Pontiac Grand Prix

1 Answer

The wiper motor on my 1983 Ford Ranger still works but the wipers no longer move. I think there is a failure of the mechanical linkage. Where do I go to find repair parts?


why do you think the motor still works if the wipers don't move? Can you hear the motor run or can you see a little movement when you turn the switch on?

What happens when you activate the washers?

go to a salvage yard that allows you to remove the parts yourself. Then you can see how the motor and linkage assembly comes out.


don't have 1983 info, but here is 1994:

Section 01-16A: Wiper and Washer System, Ranger/Explorer 1994 Ranger and Explorer Vehicles Workshop Manual
DESCRIPTION AND OPERATION Windshield Wiper System, Ranger/Explorer The windshield wipers are actuated by a permanent magnet, rotary-type electric windshield wiper motor (17504) . The two windshield wiper pivot arms (17526) and windshield wiper blades (17528) are mounted on a pivot shaft, one at each side of the windshield. The windshield wiper mounting arm and pivot shaft (17566) are connected to the motor by windshield wiper adapter and connecting arm clip (17531) . Ranger and Explorer vehicles are equipped with an interval wiper and washer (IWW) system featuring a lever-type turn signal and windshield wiper switch (13K359) mounted on the steering column. The IWW windshield wiper governor (17C476) uses a relay contact to control current to the windshield wiper motor . The governor electronic circuitry controls the contact to supply current to windshield wiper motor . A rear wiper/washer system is available on Explorer vehicles. The rear window wiper system consists of a windshield wiper motor mounted inside the liftgate (40010) , an articulating windshield wiper pivot arm and windshield wiper blade , a windshield wiper/washer switch (17A553) and an inline circuit breaker. The front electric windshield washer system consists of a control switch, integral with the turn signal, a windshield washer reservoir (17618) and windshield wiper motor and the necessary windshield washer hoses (17A605) , windshield washer nozzle jet and brackets (17603) and attaching parts.
------------------------------------------------------------------------------------------------
Pivot Shafts and Linkage Removal and Installation
NOTE: The left and right pivot and windshield wiper adapter and connecting arm clip assemblies are serviced separately.
  1. Perform Steps 1 through 9 of Windshield Wiper Motor Removal as described in this section.
  1. If servicing left windshield wiper adapter and connecting arm clip , remove left windshield wiper mounting arm and pivot shaft and windshield wiper blade assembly.
  1. Remove left windshield wiper adapter and connecting arm clip access cover.
  1. Remove left pivot nut, lower windshield wiper adapter and connecting arm clip and slide it out through left access opening. For installation, follow removal procedures in reverse order. Tighten nut to 10-13 Nm (7-10 ft-lb). Make sure the clip is fully seated in the windshield wiper adapter and connecting arm clip . Do not try to install clip with windshield wiper adapter and connecting arm clip on motor crank pin.
----------------------------------------------------------
Windshield Wiper Motor Windshield wiper motor are not serviceable. If worn or damaged, the windshield wiper motor must be replaced as an assembly. Removal
  1. Cycle windshield wiper blades until in straight-up position and turn ignition switch OFF.
  1. Disconnect battery and wiper motor electrical connector.
  1. Remove the right windshield wiper mounting arm and pivot shaft and windshield wiper blade .
  1. Disconnect the battery ground cable (14301).
  1. Remove the right pivot nut and allow the windshield wiper adapter and connecting arm clip to drop into the cowl top outer panel .
  1. Remove the linkage access cover, located on the right side of the dash panel near the windshield wiper motor.
  1. Reach through the access cover opening and unsnap the wiper motor clip.
  1. Push the clip away from the windshield wiper adapter and connecting arm clip until it clears the nib on the crack pin. Then, push the clip off the windshield wiper adapter and connecting arm clip.
  1. Remove the windshield wiper adapter and connecting arm clip from windshield wiper motor crank pin.
  1. Remove nut and ground strap.
  1. Remove three attaching nuts from windshield wiper motor. Remove the windshield wiper motor .
Installation
  1. Position the windshield wiper motor and install the three attaching screws. Tighten to 13.6-19.0 Nm (10-14 ft-lb).
  1. Install nut and ground strap.
  1. Connect wiper motor electrical connector.
  1. Install clip completely onto right windshield wiper adapter and connecting arm clip. Make sure the clip is fully seated. Do not put the windshield wiper adapter and connecting arm clip on the motor crank pin and then try to install the clip.
  1. Install the left windshield wiper adapter and connecting arm clip onto the wiper motor crank pin.
  1. Install the right windshield wiper adapter and connecting arm clip onto the wiper motor crank pin. Pull the windshield wiper adapter and connecting arm clip onto the crank pin until it snaps into place. The clip is properly installed if the nib is protruding through the center of the clip.
  1. Install the right windshield wiper mounting arm and pivot shaft and nut. Tighten the nut to 9.5-12.5 Nm (84-110 in-lb). NOTE: When the battery has been disconnected and reconnected, some abnormal drive symptoms may occur while the powertrain control module (PCM) (12A650) relearns its adaptive strategy. The vehicle may need to be driven 10 miles or more to relearn the strategy.
  1. Connect the battery ground cable and turn the ignition switch on. Turn turn signal and windshield wiper switch off so windshield wiper motor will park, then turn ignition switch off. Replace right windshield wiper adapter and connecting arm clip access cover.
  1. Install the windshield wiper mounting arm and pivot shaft and windshield wiper blade assemblies on the pivot shafts to dimension X. Dimension X is the distance between the centerline of the blade saddle and the top edge of the cowl top outer panel grille. The value of Dimension X for each vehicle is given in the Dimension X chart in the Specifications portion of this section.
  1. Test the system.
6bd608c.gif

Jan 04, 2010 | 1983 Ford Ranger

1 Answer

ROVER MGF.REMOVING WIPER MECHANISM.


Pivot Shafts and Linkage
The windshield wiper assembly is mounted below cowl top extension (021A36) . Linkages are connected with non-removable plastic ball joints. Windshield wiper mounting arm and pivot shafts are an integral part of the windshield wiper and are serviced as one unit. Removal
  1. Disconnect the battery ground cable (14301). Refer to Section 14-01 .
  1. Remove antenna mast from the antenna base.
  1. Remove cap on LH and RH windshield wiper pivot arms to expose nuts retaining the arms to pivot shafts.
  1. Remove two nuts, one from each of windshield wiper pivot arms . Lift wiper arms to service position, carefully rocking them back and forth to loosen them from the pivot shaft. Lift off windshield wiper pivot arms .
  1. Remove seven screws retaining the cowl top vent panel.
  1. Disconnect windshield washer hose (17A605) at LH side of vehicle just ahead of where it enters cowl top.
  1. Remove hood cowl seal.
  1. Carefully remove cowl top vent panel from vehicle.
  1. Remove three retaining screws to cowl drain tube that is connected to top cowl.
  1. Disconnect wiring harness leading to windshield wiper motor.
  1. Remove five screws retaining cowl top to vehicle and remove cowl top and windshield wiper from vehicle.
  1. Remove two screws and two nuts retaining windshield wiper to cowl top and separate the two parts.
  1. Remove drive linkage from motor shaft linkage.
  1. Remove remaining screws attaching windshield wiper and separate the two parts.
1086bde.gif

Item Part Number Description 1 02010 Cowl Top Panel 2 N621906-S2 Nut (2 Req'd) 3 17508 Windshield Wiper Motor 4 N805605-S36 Screw (2 Req'd) 5 17500 Windshield Wiper Assembly A — Tighten to 9-12 Nm (80-106 Lb-In)

Feb 23, 2009 | 1998 Ford Windstar

2 Answers

How do you remove old broken windshield wipers from its arm. what tool do you use.


Look on the wiper arm where it contacts the blade assembly. There should be a small plastic device that can compress between you finger & thumb. Once this clip is squeezed together, pull the wiper blade down towards the base, to dislocate it from the clipping area, and then wind it off of the arm itself, you should not need any tools.

Oct 14, 2008 | 2001 Toyota Camry

9 Answers

97 nissan sentra windshield wiper linkage arm disconnected


Most likely you will have to replace the wiper linkage from the center pivot to the left or drivers-side wiper pivot. The plastic piece in the linkage gets brittle over time and breaks down. To save a hassle in the future, replace both linkages. It should be under $20.00 for parts.

Jul 13, 2008 | 1997 Nissan Sentra

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

338 people viewed this question

Ask a Question

Usually answered in minutes!

Top Pontiac Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Pontiac Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...