Question about 2004 Pontiac Grand Am

1 Answer

My turn signal noise is still on sometimes after i've turned, my brights don't stay on, keyless entry not working,and rear defrost not working.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Pontiac Master
  • 14,036 Answers

TURN SIGNAL PROBLEM IS THE THE MULTIFUNCTION SWITCH.KEYLESS ENTRY REMOTES NEED NEW BATTERIES.THE DEALERSHIP WILL CHANGE REMOTE BATTERY AND REPROGRAM DOOR LOCKS.CHECK REAR DEFOGGER FUSE AND RELAY.IF BOTH GOOD.YOU HAVE A FAULTY DEFOGGER SWITCH OR OPEN IN THE GRID.YOU CAN BUY A GRID REPAIR KIT AT AUTO ZONE OR ADVANCE AUTO PARTS AND OREILLYS.

Posted on Jan 31, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

My daughter pushed a couple of buttons on the 2008 Ford Escape keyless entry. Now the car will turn over but not start. Where do I find the reset code for the keyless entry without taking it in.


Sometimes it's written in the owners manual .
Pushing buttons on that shouldn't cause any problem. I'd disconnect the battery for 10 minutes and reconnect. Might help. don-ohio (:^)

Jan 30, 2017 | Ford Cars & Trucks

1 Answer

Why both turn signals don't work


For the defroster:

Turn the defroster on and check for 12v at the connector on the window. If you have 12v, check for breaks in the element (the thin lines running across the window). If you do not have 12v and the fuse is good, the culprit will most likely either be the switch or the wiring.

For the right park light:

Check the bulb socket. You should have 12v at one terminal (with the park lights on) and ground at the other. If the voltage and ground are ok, you either have a bad bulb or possibly a bad socket. By bad socket I mean they can sometimes distort and not allow the terminals to make good enough contact.

Hope this was helpful.

Oct 20, 2011 | Cars & Trucks

1 Answer

My turn left signal stays on


possibly your keyless entry module keeping both front and rear lights on one side on. or indicator (flasher can) relay
remove flasher can and see if fault still there?
no - flasher can
yes - possibly keyless entry module/central door locking module or short to power on that circuit
remove now keyless entry modle to see if fault still there
no - that module
yes - try next module if fitted or if not find short in wiring.

Jan 20, 2011 | 1999 Isuzu Trooper

1 Answer

Periodic problems with keyless entry and tailgate


There is a ground strap, goes from frame to cab. normally toward front of cab

Apr 17, 2010 | 2005 Chevrolet TrailBlazer

1 Answer

Keyless locks dont work, Turn signals dont work,


sounds like you have 2 seperate problems..locks:there is software update for inoperative keyless entry/power locks..body control module software update..as far as i know,only dealer can do this..takes about an hour..signal lights:have seen a faulty multifunction switch cause this problem..switch is about 80 bucks

Sep 15, 2009 | 2005 Dodge Grand Caravan

1 Answer

Have a 2008 Chevy Cobalt, tire sensor is staying on all the tire, not reading the tire pressure at all, has 2 dashes instead. Called and talked to dealership mechanic, he said that re-registering the...


On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated....Next
  • Increase/decrease the tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate....Next
    1. After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 2 for the remaining 3 sensors in the following order:
    1. Right front
    2. Right rear
    3. Left rear
    4. When the left rear sensor has been learned and a double horn chirp has sounded, the learn process is complete and the RCDLR exits the learn mode.
    5. Ignition OFF, adjust all tires to the recommended pressures. Refer to Vehicle Certification, Tire Placard, Anti-Theft, and Service Parts ID Label

    Jul 29, 2009 | 2008 Chevrolet Cobalt

    1 Answer

    Brights stuck on along with turn signal


    Short in the turn signal switch. Should cost around $75 to replace and about 20 minutes.

    Jun 17, 2009 | 2002 Mitsubishi Galant

    1 Answer

    Key Pad Entry does not work


    does the key pad light when you press a button at night? If yes, the fuse is ok.
    Do you have the plastic card with the permanent code in your owner manual packet? If yes, tryit.
    report back.

    Keyless Entry The keyless entry keypad is hardwired to the GEM. The GEM interprets the inputs from the keyless entry keypad and then controls the associated operation. The keyless entry keypad will be illuminated for five seconds when any button is pressed. Additionally, it will request the illuminated entry feature to turn the courtesy lamps on. If a lock all doors code is entered, the illumination will turn off, as well as request the illuminated entry feature to turn off the courtesy lamps. When pressed, the keyless entry keypad supplies the ground signal to the GEM or the GEM receives a signal from the keyless entry remote transmitter. Then the GEM outputs a ground signal to the appropriate lock or unlock relay which supplies the power to the actuator to lock or unlocks all doors, including the luggage compartment. The keyless entry remote transmitter also unlocks the liftgate or activates the panic alarm by sending a signal to the GEM.
    --------------------------------------------------------------- Visual Inspection Chart Mechanical Electrical
    • Keyless entry keypad
    • Keyless entry remote transmitter
    • Central junction box (CJB) Fuse F222 (20A)
    • Circuitry
    • Generic electronic module (GEM)
    ------------------------------------------------------------------------
    • No communication with generic electronic module (GEM)
    • Generic electronic module.
    • Circuitry.
    • REFER to Section 419-10 .
    ------------------------------------------------------------------------------------

    Mar 08, 2009 | 2003 Ford Taurus

    1 Answer

    Gmc sierra 2008 low tire pressure problem


    You can follow this to reset it.
    Ignition ON, initiate the TPM Learn Mode
    using one of the following procedures:

    1. On vehicles equipped with keyless entry, simultaneously press the keyless entry transmitters lock and unlock buttons until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
    2. On vehicles not equipped with keyless entry, press and release the driver information center (DIC) INFO button until the TIRE LEARN message appears on the DIC display. Press and hold the SET/RESET button until a double horn chirp sounds indicating the Learn Mode has been enabled. The left front turn signal will also be illuminated.
    3. Increase/decrease the tire pressure for 8-10 seconds then wait for a horn chirp. The horn chirp may occur before or up to 30 seconds after the 8-10 second pressure increase/decrease time period has been reached. Once the horn chirp has sounded, the sensor information is learned and the turn signal in the next location to be learned will illuminate.
      After the horn chirp has sounded and the right front turn signal is illuminated, repeat step 2 for the remaining 3 sensors in the following order:
      3.1. Right front

      3.2. Right rear

      3.3. Left rear

      When the left rear sensor has been learned and a double horn chirp has sounded, the learn process is complete and the RCDLR exits the learn mode.
      Ignition OFF, adjust all tires to the recommended pressures

    Jan 22, 2009 | 2000 GMC New Sierra 1500

    Not finding what you are looking for?
    2004 Pontiac Grand Am Logo

    231 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Pontiac Experts

    yadayada
    yadayada

    Level 3 Expert

    76164 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22156 Answers

    Jeff Turcotte
    Jeff Turcotte

    Level 3 Expert

    8273 Answers

    Are you a Pontiac Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides

    Loading...