Question about 1970 Oldsmobile 442

1 Answer

1971 olds 442 th-400 gear selector stuck in drive. what could be the problem?

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Renaissance:

    An user who is expert in 3 categories / brands.

  • Oldsmobile Master
  • 1,949 Answers

The wire to the indacator has broken some are a small string some are cable if it is the cable u can soider it bake together

Posted on Dec 08, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Stuck in drive wont shift in any other gear any advice?


jack up and safely go under neath vehicle and check the shift selector connection if good check cable /linkage from tranny to selector for proper connections and operations if good --try moving selector if moves try to put in neutral if hard to move or selector wont move possible internal gear damage

May 09, 2016 | 1983 Pontiac Firebird

1 Answer

Extended cab. How do I uncross gears?


if you are stuck in gear it is not a basic rebuild but a bad rebuild
because of the design of the gear selection process , it is impossible to have 2 gears selected together as one selector shaft will not move unless another selector shaft is in the correct position ( neutral ) to allow the detente balls to move out of the way so the next selector shaft can move
it is possible that the gear stick is not in the correct position when it was installed back onto the top of the box and one gear was selected and the end of the lever came out of the selector slot or all the selectors were not in the neutral position and so the end of the lever went behind a selector rail
pull the gear lever turret of the top of the box, move the selector rails until they all line up as a slot across all of them , then put the gear lever end back in that neutral slot

Dec 27, 2015 | 1992 Ford Ranger

1 Answer

71 cutluss rear end moving back and forth why


Get under the car & find out why

Obviously rust is playing a part or someone failed
to make the proper repairs in the past

You provided nothing to go by in your question

Not many folks left that were around in 1971 to
even know the car

May 21, 2014 | 1971 Oldsmobile 442

1 Answer

My 1998 Landrover Discovery won't go into drive/ stuck in park now stuck in reverse won't go into drive. Professional say transmission is good. Silonoid was removed ???? Literally STUCK!


Check the condition and adjustment of the gear selector mechanism and cable all the way from the gear lever to the gearbox selector mechanism.

May 02, 2014 | Cars & Trucks

1 Answer

Have 1971 442 got 12.5 volts on gagego to start and gage goes down to zero.put battery charger on for seconds gage goes to 14 car starts shut car off wont start again.tryed new starternew battery can you...


got family here and they are all talking at once and its putting me off a slight bit ,right try charging the battery for about 2/3 days and see what happens then get back via this reply ,as i need to know is it cranking or is is turning over but not starting.

Jul 04, 2010 | 1970 Oldsmobile 442

1 Answer

All the gear indicators PRN321 on th dash of my 87 Tornado are flashing, what gives?


The gear selector switch is either out of adjustment or it is bad. Loosen the two bolts holding the gear selector in place and turn it slightly to see if the display stops flashing. You will have to manually shift the transmission lever at the switch into neutral, and then turn the switch until the display says neutral. Tighten the bolts and then check all gears. It's also possible the shift cable could also be out of adjustment. Does the display change if you simply wiggle the gear selector lever?

Dec 02, 2009 | 1987 Oldsmobile Toronado

1 Answer

70 Olds 442 ignition cylinder and ignition gear replace


check the internet there is a place in portland oregon that sells all these parts sorry I lost the number

Oct 20, 2009 | 1970 Oldsmobile 442

Not finding what you are looking for?
Cars & Trucks Logo

Related Topics:

170 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

75005 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7710 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...