Question about 2001 Chevrolet Tracker

1 Answer

I need to take off my door panel to change the speakers in my truck how can i get it over the window crank?

Posted by on


1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points


    An expert that got 10 achievements.


    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 593 Answers

There is a tool made just for this purpose. Go to any auto parts store
autozone/advance or napa etc. and ask for a window crank removal tool.
They cost about $10.00. There is a spring clip between the crank and the door panel. Locate the open end of the clip, and slide the tool between the crank and panel, the clip should pop right off. Be sure not to loose the clip. To put it back , slide the clip over the two slits on the
crank and push it back on. I hope I was of some help. Good luck.

Posted on Jan 30, 2010


1 Suggested Answer

  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

a 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of.(from cars to computers, handyman, and even drones)
click here to download the app (for users in the US for now) and get all the help you need.

Posted on Jan 02, 2017


Add Your Answer

Uploading: 0%


Complete. Click "Add" to insert your video. Add



Related Questions:

1 Answer

No sound from speakers in 2000 GMC Yukon? Whats going on?

1 Disconnect the trucks negative battery cable.
  • 2 Unhook the clip for the door's manual window crank with a hooked tool behind the handle (or rub a rag behind the handle), or for a power window, pry off the window switch assembly from the door handle with a trim stick and disconnect its electrical connector.
  • 3 Pry off all small panels and bezels on or near the door with the trim stick, including the triangular panel on the mirror mount and the bezel surrounding the door handle.
  • 4 Unscrew and remove all of the mounting screws for the door's inner trim panel then pull the panel out to detach the clips. Disconnect all remaining electrical connectors on the door panel.
  • 5 Peel off the plastic water deflector sheet from the door.
  • 6 Press down on the speaker's upper mounting tab while grasping the speaker, then tilt the speaker out of the door frame and lift it off the tabs on the bottom. Disconnect the speaker's electrical connector.
  • Connect the replacement speaker to the electrical connector.
  • 8 Secure the speaker to the lower tabs and pivot it into the mounting hole, clipping it in place with the door's mounting tab.
  • 9 Press the plastic shield back into place on the door.
  • 10 Reconnect the trim panel onto the door, connecting all needed electrical connectors and engaging all its clips, then apply its mounting screws. Reconnect all smaller panels and bezels to the panel.
  • 11 Reinstall the window crank or control switch with its clip or electrical connector.
  • 12 Reconnect the black battery cable onto the negative terminal.


  • Jun 01, 2012 | GMC Yukon XL Cars & Trucks

    2 Answers

    The window on my 2004 Ford F-150 fell into the door. How do I take the door apart to put the window back on track?

    There are usually screws holding the door panel in place. Look around the edge of the inner door panel for any screws. There are also some screws under the arm rest on the door. Any items that penetrate the door panel must also be moved out of the way or removed (like window cranks).
    Once you get all screws and obstructions out, the panel moves away from the door and lifts up and away. You may find that the window didn't come off track, but you may need to replace some parts as well.


    Aug 09, 2011 | 2004 Ford F150

    1 Answer

    Need to know the proper way to tack off the rear door panel on my 2009 1500 dodge truck so I can put new speakers in

    1426215.jpg 1. Using trim stick C-4755 or equivalent, release the door switch/bezel (1) from the door trim and disconnect the electrical connectors (2).

    1426183.jpg 2. Using trim stick C-4755 or equivalent, release the upper trim bezel (1).

    178637.jpg 3. If equipped, remove the manual window crank (1) using a window crank removal tool (2).

    1426196.jpg 4. Remove the screw (3) and remove the interior handle bezel (5). 5. Release the plastic screw/rivets (4). 6. Raise the trim panel (2) up and off the hooks and door lock knob (1).

    Apr 22, 2011 | Dodge Ram 1500 Cars & Trucks

    1 Answer

    Passenger door removal for radio speaker access.


    Apr 04, 2010 | 2007 Chevrolet Cobalt Coupe

    1 Answer

    Need to remove driver side door panel?

    1. Disconnect the negative battery cable.
    2. If equipped with an accessory switch panel, carefully pry the switch panel up and away from the door panel. Tag and disconnect the switches from the panel.
    3. On 1981-86 models, remove armrest attaching screws.
    4. On 1987-96 models, remove the retainer screws secure the pocket in the molded armrest on the door panel.
    5. If equipped with crank type windows, remove window crank handle with the appropriate clip removal tool.
    6. If equipped with manual remote mirrors, remove the control knob bezel.
    7. Remove inside door handle cover attaching screw and trim plate.
    8. If equipped with door mounted speakers, remove the speaker, and disconnect the speaker wires. For speaker removal and installation steps, refer to .
    9. Remove all external screws securing the door panel. Insert an appropriate prytool between the door panel and door frame to remove the hidden clips securing the panel.
    10. Holding door panel vertical lift straight up to release the upper clip.
    11. Inspect all retaining clips and replace any broken or missing pieces.

    To install:
    1. Position the door to the door and carefully press on the retainer clips to engage. If a clip will not engage, inspect the mounting hole behind the panel to make sure the clip is properly aligned. Install any panel-to-door retainer screws.
    2. If equipped with crank windows, attach the washer and crank to the window regulator stud.
    3. On 1981-86 models, attach the armrest to the door using the retainer screws.
    4. On 1987-96 models, insert the armrest pocket and secure in place with retainer screws.
    5. If equipped with door panel mounted speakers, attach the speaker wires to the speaker and secure the assembly to the door panel.
    6. If equipped with remote cable mirrors, attach the control knob to the door panel with the retainer bezel.
    7. If equipped with an ashtray, insert the holder assembly, and secure in place with retainer screws. Install the ashtray to the holder assembly.
    8. Position the door handle trim panel around the door handle assembly, and secure in place with the retainer screw.
    9. If equipped with accessory switch panel, attach the harnesses to the switches, and press the accessory plate into the door panel.
    10. Connect the negative battery cable.
    11. Check and make sure all panel components function correctly.

    Apr 03, 2010 | 2002 Ford Explorer Sport Trac

    1 Answer

    Remove a door panel on a mazda atenza in order to change the speakers?

    the panel is held on by plastic clips and a few phillips head screws remove the screws, they are probably in the arm rest and the handle, also if you have a manual window crank that needs removed also then just give a slight tug and the panel should come right off

    Mar 15, 2010 | 2005 Mazda 6

    1 Answer

    How to remove the inside door panel from a dodge 2005 2500 pick up

    Release door latch and open door.
    Roll window down.
    Remove window crank Window Crank - Typical , if equipped.
    Remove screws attaching trim panel to door Door Trim Panel and Trim Panel Screw
    CAUTION: Do not forcibly pull trim panel from door, damage to trim panel may occur.

    Simultaneously lift upward and outward to release retainer steps from inner door panel Trim Panel Retainer
    Disengage inside handle linkage rod from inside handle.
    Disconnect speaker harness wire connector Speaker And Power Mirror Connector
    Disengage power mirror wire connector, if equipped (driver's side only) Speaker And Power Mirror Connector
    Disengage clips attaching power window/lock switch panel to door trim panel. Disengage wire connector from switch panel, if equipped Power Door Lock/Window Connector
    Separate door trim panel from vehicle.
    Position trim panel at door.
    Engage wire connector for window/lock switch panel, if equipped. Engage clips attaching power window/lock switch panel to door trim panel.
    Engage power mirror wire connector, if equipped.
    Connect speaker harness wire connector.
    Engage inside handle linkage rod to inside handle.
    Align trim panel retainer steps with inner door panel and slide trim panel into place.
    Install screws attaching trim panel to door.
    Install window crank, if equipped.

    Hope helped with this; remember rated this help. Good luck.

    Nov 12, 2009 | 2005 Dodge Ram 2500 Truck

    1 Answer

    I need to take the window crank handle off of my door

    auto parts store h as special tool to remove clips but u can use a flathead scerw driver gently pull handle from door panel and sneak screw driver behind handle pushing c clip out but becarefull they sometimes shoot out

    Mar 26, 2009 | 1995 Dodge Neon

    1 Answer

    How do I remove the door panels to change the speakers in the front doors of a 1999 Ford Escort?

    remove the front door pull cup screw
    remove the screw cap and screw from inside handle and slide the handle rearward to disengage the hook from the inner sheet metal. disconnect inside handle from latch remote link if manual windows- remove crank with store bought remover tool. Remove the 2 pushpins from the door trim panel using trim tool pry away door panel [7] fasteners holding panel and push panel in and up . if elect windows disconnect switches

    Feb 17, 2009 | 1998 Ford Escort

    1 Answer

    97 VW Jetta right rear power window off track

    There should be six or seven allen wrench screws around the edge of the door panels. Loosening these releases the retaining clips inside. You will then want to remove the manual window crank if you have one by laying two fingers flat on the door panel and pushing the ring around the base of the crank sideways. You might have to rotate around this as it only pushes one way. Next you will have to remove the two large golden screws directly under the door panels handle. If you have rear door panel speakers you will have to politely pry off the speaker grill with a flat blade screwdriver and remove the speakers four screws and the wire clip from behind the speaker. You will also have to unscrew the door lock post. Then you should be able to lift the door panel up to release the top lip of it from the door.

    Dec 29, 2008 | 1997 Volkswagen Jetta

    Not finding what you are looking for?
    2001 Chevrolet Tracker Logo

    141 people viewed this question

    Ask a Question

    Usually answered in minutes!

    Top Chevrolet Experts


    Level 3 Expert

    76846 Answers

    Colin Stickland
    Colin Stickland

    Level 3 Expert

    22246 Answers

    Ronny Bennett Sr.
    Ronny Bennett Sr.

    Level 3 Expert

    6927 Answers

    Are you a Chevrolet Expert? Answer questions, earn points and help others

    Answer questions

    Manuals & User Guides