Question about 1998 Subaru Legacy

1 Answer

I have a 1998 Subaru Outback Legacy 2.5 liter manual trans. When you turn the key it just clicks.

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Vice President:

    An expert whose answer got voted for 100 times.

  • Master
  • 431 Answers

Clicking in this situation is due to either a low battery, the solenoid and/or starter, or a bad connection at the battery, the ground, or the starter & solenoid connections.

Autoparts stores like autozone will lend you a good battery while they charge yours if it tests low & after making sure the battery is fully charged, clean the terminal connections and try again. If you still have the problem you will need to test the solenoid & starter independently after checking to be sure the starter is tightly installed, no wiggle & the wires all have good connections as mentioned above. Good luck.

Posted on Jan 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fuel filter located on a 1998 Subaru Legacy 2.2 liter outback?


I don't have a picture WHERE it is located but it is in your engine compartment. It looks like this:


b467b4b.jpg

Sep 13, 2010 | Subaru Legacy Cars & Trucks

1 Answer

I HAVE A 1998 LEGACY OUTBACK NO SMOKE NO SWEET


have you got heat in the car,what im saying is when you turn on the heater inside the car what happens?im not getting your drift,but get the thermostat checked out sounds like its not letting the coolant flow.adrian,,,,

Jul 21, 2010 | 1998 Subaru Legacy

3 Answers

On my 1998 Subaru Legacy, the light on heater/fan switches don't light up, any idea how to fix it?


Funny you should ask - we have the same problem on a '96 outback. Then i noticed those lights go out on our '90 legacy and come back on when i smacked the dashboard. it appears that there is a short somewhere behind the switches. Going to try and dig in today and will let you know what i find...

Jan 19, 2010 | 1998 Subaru Legacy

1 Answer

1998 Subaru Legacy Outback--Rough Idle


I have the same problem!Running on three.I have checked compression,wires,plugs.Changed injecters,plugs.
3 mech.cant figuire it out???

Nov 21, 2009 | 1998 Subaru Legacy

1 Answer

1999 Subaru Legacy Outback 5th gear popping out


WELL IT SOUND LIKE YOUR TRANS IS GOING DOWN YOU NEED TO LOOK AT TRANS FLUID TO SEE IF IT IS CLEAR LOOKING OR IS IT LOOK LIKE METAL MAY BE IN IT DRAIN A LITTLE IN A PAN THE LOOK AT IT IN SOME LIGHT AND SEE IF IT LOOKS LIKE GOLD FLAKES OR SHING METEL IF SO TRANS HAS INTERNAL ISUSES

Aug 13, 2009 | 1999 Subaru Legacy

1 Answer

Steering wheel clicks on 1998 Subaru Legacy Outback wagon


steering column bearing sounds like a worn out steering column... jack the front wheels off the ground both sides relieve load on steering wheel to see if it lessens the amount of feel and noise, if it does it shoud be the column bearing, replace bearings or complete column,,, also try with the wheels off the ground and safely supported to manualy steer the wheels by hand and see if you feel in roughness or hear any noises,should some minor resistance but be smooth in it movement if everything suspension and steering component wise is in good working condition... please rate my help.. thanks...

Aug 05, 2009 | 1997 Subaru Outback

1 Answer

How difficult is it to change the rear struts on a 1998 Subaru Legacy Outback, 2.5, automatic trans?


Removing and replacing is not the problem, easy job. Changing the springs is the only problem. Make sure you are very careful when removing springs. Better to have a parts store do it for you. If you do decide to change yourself just make sure clamps are tight and take your time to follow directions exactly. Be careful, good luck and have a great day.

Jun 24, 2009 | 1998 Subaru Legacy

1 Answer

1999 subaru legacy outback with manual trans won't go into gear?


ok maybe it needs adjustments or it may need some trans repairs

Jan 23, 2009 | 1999 Subaru Legacy

1 Answer

My running lights will not turn off unless I unhook the battery.


Subaru Outback Legacy Flashing
Q. I have a 1996 Subaru Outback Legacy AWD manual transmission. the hazards flash when I turn the car off. I tried to reset the system by pushing the little black button under the drivers' side dash but it won't reset the system. I had problems with the brakes so I did not drive it for about two months and when I tried to start the car the battery was dead.
mechanic.jpg Now the brakes are fixed but the hazards won't quit flashing and the guy who repaired the car said I needed to reset the system by pushing the little black button. And I don't know if I should have it looked at, or change the battery, or if it is something very simple I can fix by my self.
Thank you very much,
Patrick
A. Patrick, you are the third person in the last two days that has come to me with this same exact problem under the same conditions. As of now I don't have any concrete information on this, but I believe the problem to be in the alarm system.
I believe the battery being disconnected or dying does something to the Anti-theft and Alarm System module and having a Subaru dealer reset the system will correct it.
If you do this and it works, please, let me know and I will pass the information on to the others.
Added 11/7/2003
Dear Mr. Ciulla,
I read your Q&A titled "Subaru Outback Legacy Flashing". I recently had the same problem on my 1996 2.5 liter Subaru Legacy Outback and your response is correct but I can give you a little more detail on what worked for me to stop the light flashing (which occurs sometimes if the battery had been dead):
There is a black reset button under the I/P near the anti-theft module.
  1. Turn ignition on
  2. Hold button 20+ seconds (door locks will lock/unlock 3 times)
  3. Turn ignition off
This also resets the key FOB so as step 2.5 you should also press the "lock" button on the key FOB before releasing the black reset button (door locks will lock/unlock one more time--do this with each key FOB you own). That's all!
The questioner in your Q&A said he tried the reset button; I suspect he either didn't turn the ignition on/off or didn't hold it in for over 20 seconds.
PS... pulling the door lock fuse will stop it temporarily if you can't get the above to work and have to take it to the dealer
Regards,
John
subaru.jpg
Photo Courtesy John Spieth ©2003
Additional Information provided courtesy of ALLDATA

Nov 26, 2008 | 1998 Subaru Legacy

Not finding what you are looking for?
1998 Subaru Legacy Logo

272 people viewed this question

Ask a Question

Usually answered in minutes!

Top Subaru Experts

yadayada
yadayada

Level 3 Expert

77169 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22265 Answers

Brandon Johnson
Brandon Johnson

Level 2 Expert

251 Answers

Are you a Subaru Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...