Question about 1995 Geo Tracker

1 Answer

How do i remove ignition key tumbler without key

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    Superstar:

    An expert that got 20 achievements.

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

  • Master
  • 10,319 Answers

You don't The only way is to drill it out although many other parts will be destroyed as well

Posted on Jan 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

What tool is needed to remove the bad ignition switch


I suggest a locksmith be called in to remove the barrel
he will be able to supply a new barrel and cut the key to suit what you have and set the tumblers to the new key

Jun 09, 2015 | Cars & Trucks

1 Answer

My key wont go into ignition of my 2003 Cadillac deville. Are there any solutions to getting the key to go into ignition?


If you are unable to insert the key it might be because the tumbler has been turned past the point of key release it happens a lot with worn ignition tumblers try turning the ignition tumbler forward as if to attempt to start it without the key then try to insert the key if that doesn't work try turning it the opposite direction when you get it inserted you need to replace the tumbler asap if anyone who entends on stealing your car the knowledge that you have reported is enough to raise eyebrows of anyone who has bad ententions! I hope that solves your problem?

Mar 01, 2015 | 2003 Cadillac Deville

1 Answer

How do i replace my ignition lock cylinder in my 2000 Mitsubishi mirage without the key?


best advice is to get a locksmith to do the job. They will be able to put in a new tumbler, supply the correct fob keys for the immobiliser and possible program it to the vehicle . IF not you will have to take the keys and the vehicle to a service dealer to have it programmed.

Dec 27, 2014 | 2000 Mitsubishi Mirage

1 Answer

What is the proper way to chisel out tumblers in an ignition lock cylinder


Without knowing what your driving I can only guess. But you don't chisel out the tumblers. You have to remove the lock assm. from the column and on the lock cyl. there will be a strip of metal which has to be gently pried off and you will find 5 springs. At the bottom of those springs are the tumblers. Be careful of those tumblers get one in the wrong place and your key will no longer work. What is the reason you want to chisel out the tumblers???? You may be going about the problem all wrong.

Mar 07, 2013 | Cars & Trucks

1 Answer

Ignition key tumbler


Look on the bottom of the housing, use a high speed 3/16 drill bit.

Apr 29, 2012 | Cars & Trucks

1 Answer

Remove broken key from gm ignition lock


Physically removing a piece of an ignition key from the tumbler is practically impossible. The tumbler is filled with spring loaded tabs which raise and lower against EVERY notch on a key. That resistance will fight your every motion as you try to back the key remnant out. As one tab releases, the next in line raises into the vacancy just created. GM, even with the "fob"/ chip installed in most of their keys, also put greater anti-theft detail into their ignition tumblers. IF this is an ignition lock that has a chip sensor, the practical repair is a complete key/tumbler replacement. This isn't a DIY repair. It will involve removing the steering wheel and column covers, air bag, AND re-coding the vehicle computer to accept and recognize the new key/chip code. The re-coding CAN be done at home. Immediately after the new tumbler is installed, leaving the ignition in the "run" position for 1 hour, will re-code the antitheft in the computer.

Feb 21, 2012 | Buick Regal Cars & Trucks

1 Answer

Removal and replacement of key tumbler 1994 Ford explorer


look at the steering column below the ign lock and tumbler there should be a small hole turn key to on pos and push a small rod up the holethis then should release the lock and tumbler,no hole then wheel and coumn has to be stripped to get to lock retainer

Oct 05, 2009 | 1994 Ford Explorer Limited

2 Answers

I took the key out of the ignition but the engine was still running


IS THE IGNITION IN THE OFF POSITION AND THE VEHICLE STILL ON, NEED MORE INFORMATION. THIS VEHICLE IGNITION KEY HOLE IS SLACK, AND THE KEY IS SOMETIME ABLE TO COME OUT, WHILE THE VEHICLE IS RUNNING.

Aug 03, 2009 | 1997 Dodge Caravan

1 Answer

Power is on all the time with or without the key in the ignition. There are no positions (ie...accessories, on, start). When the key is inserted it moves freely in all positions. I removed the steering...


ok some where on the tumbler there will be a very small pin hole you will have to put the key in turn it forward one click then take something that will fit in the pin hole and push in and pull out on the key this should remove the tumbler then follow the directions on the new tumbler to put it in

Jun 06, 2009 | 2001 Ford Ranger Regular Cab

1 Answer

Ford taurus 1996


Place key in ign. lock n tumbler and turn to "on" position. Under the column you'll see a small hole to put a small screwdriver or rod into and press it in. While you're pressing it, pull the lock n tumbler out. Installation is the reverse of removal but without the use of the rod. Just push the lock n tumbler in the hole and turn key to lock position and pull key out.

Jul 28, 2008 | 1996 Ford Taurus

Not finding what you are looking for?
1995 Geo Tracker Logo

Related Topics:

225 people viewed this question

Ask a Question

Usually answered in minutes!

Top Geo Experts

yadayada
yadayada

Level 3 Expert

75824 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8215 Answers

Are you a Geo Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...