Question about 2002 Toyota Sequoia

Open Question

Need to get rear hatch open on '02 toyota sequoia to replace cable, got it torn down but the latch doesn't seem to disengage? do you have a diagram of the hatch assembly for breakdown?

Posted by on

6 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

  • 5 Answers

SOURCE: Broken rear hatch door handle on Toyota Sequioa

It sounds like the handle has become disconnected from the mechanism. You will have to remove the inner door panel and reattch. It is not a complicated or difficult job but if you get a professional it could cost upwards of $100.

Posted on Jul 16, 2009

  • 1348 Answers

SOURCE: DIAGRAM FOR 2002 TOYOTA SEQUOIA STARTER REMOVAL

the big red cable from the battery goes right to it.

Posted on Sep 09, 2009

  • 13 Answers

SOURCE: I broke the latch from the handle of my 2003

It will be about $200-280 at the dealer, they know all about this problem on the Sequoia.

If you want to do it yourself, it will take about 1.5 hours and some patience.

Depending on the level of corrosion in the back of your window area, the part number you need to order is the handle assy rear door. If you have a big problem, you may need the cable also:

toyotapartscheap.com (Mossey Toyota)
Parts:
1. Lock sub Assy - 69301 0C010 (($99)
2. Handle Assy Rear Door - 69090 08010 ($70)
3. Cable - 64680 0C010 ($24) .

The design is the same from 01-05 and is common to break after time. A poor design on an otherwise excellent truck.

If you want to DIY - visit Tundra Solutions.com and read up on the problem:

First, take off the license plate2_bing.gif.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.

Posted on Dec 12, 2009

  • 13 Answers

SOURCE: 2003 toyota sequoia rear door latch broken

First, take off the license plate2_bing.gif.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.

Posted on Dec 12, 2009

  • 13 Answers

SOURCE: 2001 Toyota Sequoia lift gate latch broken, door is locked closed

Take a look at my other Sequoia posts about this.

You need to remove the interior pull handle first then gently pry away the interior panels from the top down. Go look at Tundra Solutions.com for the detailed procedure on the handle assemlby replacement but here is a rundown:

First, take off the license plate2_bing.gif.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.

Posted on Dec 12, 2009

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

HOW TO OPEN HATCH BACK LOCK, IF ITS BROKEN


the sequoia hatchback handle breaking is a known problem due to the extremely low quality of the plastic. 1st you have to open the back door! there is a small pin to the right side of the hatchback door exterior handle. bend a coat hanger and put it on the small pin, pull down and the door will open. Then remove inside panel and you can undo screws and replace the hatchback door handle.

Dec 02, 2010 | 2001 Toyota Sequoia

1 Answer

Rear hatch latch was broken, replaced but now when the lock button is pressed on the transmitter the rear hatch releases and opens.


sounds like the linkage is hookup wrong and may be backwards, the release and lock/unlock linkage are in the wrong holes reverse the two and try it, this sounds like the problem.

Aug 25, 2010 | 2006 Toyota Sequoia

3 Answers

Cannot open rear hatch. have all internal panels off and can manipulate cable attachment to the locking mechinism but door still does not release. Im thinking that I will have to cut out lock mechnism just...


You can pry open the latch with a screw driver or lastly grind the latch. Try grabbing rod or cable with locking pliers and try pulling while prying at the same time.

Oct 22, 2009 | 2004 Toyota Sequoia

1 Answer

Same problem!


Yoy need to replaced the rear door handle and poss latch.
You can get the door open by removing the door panel and manually pulling on the latch cable

Aug 04, 2009 | 2006 Toyota Sequoia

1 Answer

Back Hatch latch broken


no.. common concern.. back handle breakes becausr of bad latch.. remove back panel from inside.. gain acess. will be able to open from there.. replace handle latch or both

Aug 03, 2009 | 2006 Toyota Sequoia

3 Answers

2003 toyota sequoia rear door latch broken


First, take off the license plate2_bing.gif.
Since the hatch wouldn't open, I started from the inside and took down the top trim piece. After that the two side pieces come down, then the main trim piece which covers the bulk of the door comes out. These are all popped in with the white tabs.
There are 3 access hole covers to pop out (don't forget to install them back in when done) and through the left hole you can see the mechanism to unlatch, press it down with a screwdriver and open the door. If anytime you close the door you will have to do this to unlatch, up until you disconnect the cable and pull out the handle, then you have to locate the cable and pull that directly.
Behind the large trim piece you will find a metal access cover, remove the 7 or 8 10mm bolts holding that on and pop the 3 white tabs and let it hang off to the side. Disconnect the cable from the handle assembly by reaching in from the right hand side and popping of the cable from the handle assembly.
From the left and right access holes, locate the two 10mm nuts which hold the license plate assembly to the door and remove them. Then there are 4 plastic tabs that come in from the outside that hold the license plate assembly on in each corner, try and locate those and using some pliers squeeze them together and push it through. Next locate the license plate lamps wire connector and release that from the left side, it’s the simple push in and pull out square white connector.
After these are out, put back in 1 or 2 bolts into the large metal access cover so the hatch can be lowered (don’t close it).
Here is where I had fun, begin to pop out the assembly that it was bolted to. I ended up breaking 3 of the 4 plastic tabs in each corner because I did not use pliers from the other side to pull them out, however it remained somewhat useable (hindsight 20/20).
Now the license plate assembly can be taken to a bench to replace the handle assembly (Toyota doesn't sell just the handle, it is a small assembly). Two screws out and the assembly is replaced.
Before pressing the license plate assembly back onto the truck, make certain all the plastic tabs are in the assembly and not in the truck. Reverse the process to re-install.

Jul 06, 2009 | 2003 Toyota Sequoia

2 Answers

My rear hatch door handle broke i need to replace it. how do i replace it?


how do i get the rear gate panel off so I can replace the latch on the 2003 sequoia.

Jul 06, 2009 | 2002 Toyota Sequoia

2 Answers

2003 rear door latch broken how do I get the panel open


if the door is shut, it is a real doozy but i have done it. you have to pry the inner panel off the door using hook tools and small, crowbar shaped tack pullers....kinda like a mini wonder bar. once the panel is off, you have to fish around inside the door and pull the cable on the latch by hand.

Jun 29, 2009 | 2001 Toyota Sequoia

2 Answers

Rear door latch replacement 2003 sequoia


Fig. The latch bracket shown is moved by loosening the mounting fasteners and sliding it as necessary. Matchmark the bracket to the door pillar before moving-1.8L Passat model shown

Jun 02, 2009 | 2003 Toyota Sequoia

1 Answer

Trunk won't open


latch assb has probley rust or the cable has broken inside rear hatch

May 30, 2009 | 2006 Toyota Sequoia

Not finding what you are looking for?
2002 Toyota Sequoia Logo

Related Topics:

354 people viewed this question

Ask a Question

Usually answered in minutes!

Top Toyota Experts

yadayada
yadayada

Level 3 Expert

75822 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8210 Answers

Are you a Toyota Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...