Question about 2004 Suzuki Grand Vitara

1 Answer

Cost to replace right rear axle bearings - 2004 Suzuki Grand Vitara

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    Brigadier General:

    An expert that has over 10,000 points.

  • Master
  • 3,533 Answers

It depend somewhere around $175-to $250 but this is something you can do yourself give these websites a try www.alldatadiy.com and www.autozone.com if all fails stop by your local library and get your hands on a Haynes auto repair manual for your car wish you the best of luck Michigan Man.

Posted on Jan 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

2 Answers

I hit the curb realy bad in an accident, my rear right side rim wabbles , I replaced the rim thinking it was jst the rim,!But I think its the axle!,shld I replace the whole rear end?


I dont know whar kind of vehicle or how many miles on it but if its rear wheel drive you can replace either. the rear end will cost more than an axle but if it has alot of miles on it plus you dont know about the rest of the componenents inside do the whole thing

Apr 01, 2015 | Cars & Trucks

3 Answers

2007 ford sport trac rear wheel bearing replacement


Jeff is describing how to replace the front wheel bearings. In the front, the bearing is part of a "hub cartridge". Randy is describing how to change the rear bearings on a truck with a "dead" rear axle. The sort of differential which is one massive cast iron assembly from rim to rim. However, your truck has an IRS [Independent Rear Suspension] design. You need to remove the wheels, brakes & the complete rear knuckle assembly. To remove the bearing from the knuckle requires a hydraulic press and a "knife edge" bearing removal tool. I doubt that you have these tools available. If not, find an auto parts store or auto machine shop with these tools. They can press the old bearing out and install the new one for you. Then you can reassemble the knuckle assembly from that point on. The video linked below should help you.


Ford Explorer Independent Rear Suspension Rear Wheel Bearing and Hub...


With the knuckle off, you can easily replace the ball joints at the same time. Odds are you will ruin the original ball joints getting the knuckle assembly off, anyway.

Jan 11, 2015 | 2007 Ford Explorer Sport Trac

2 Answers

What is the cost to replace rear axle?


If it is just the bearing that has failed then the cost will be 1 hour + the bearing cost. If it has damaged the axle then get a second hand unit from the wreckers and fit a new bearing and the cost will be second hand axle cost + bearing + 1 hour labour.

May 03, 2014 | 2004 Jeep Grand Cherokee

2 Answers

Hi. how would i repair a rear axle for a 2006 toyota corolla? i dont have a lift so will i need to take it to an autobody shop? if so how much do these repairs cost usually?


What are going to do to repair the axle? There really is no axle on front drive cars, the wheel assembly is connected to a hub that is mounted to the frame through swing arms. And, you would not take your car to a autobody shop for mechanical work. The cost of repairs depends on what is being done.

Nov 29, 2010 | 2006 Toyota Corolla

1 Answer

Need to remove rear axle to replace bearing


Open the rear diff cover you will see what is holding the axle in place.

Nov 21, 2009 | 2002 GMC Safari

1 Answer

Rear axle bearing lock washer and nut coming loose


You may have incorrect axle end play. The left axle is fitted with a 1mm shim and an o-ring between the bearing housing and diff flange. The right bearing housing should be shimmed to suit specs. If the right axle has too much end play, it may try to walk.

Aug 16, 2009 | 1988 Mitsubishi Pickup

1 Answer

How do you remove right rear axle on a 2004 ford crown vic to replace seal on wheel?


Section 05-02A: Axle, Integral Carrier — 8.8-Inch Ring Gear 1994 Town Car, Crown Victoria/Grand Marquis. Workshop Manual REMOVAL AND INSTALLATION Axle Shaft NOTE: Whenever replacing the rear axle lubricant, use Rear Axle Lubricant XY-90-QL (ESP-M2C154-A) or equivalent.
Removal
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: The rear brake anti-lock sensor must be removed before the axle shafts are removed. The rear brake anti-lock sensor is bolted on the rear disc brake caliper anchor plate.
  1. Raise vehicle to desired working height. Refer to Section 00-02 . Remove rear wheel (1007) and tire assembly. Remove rear disc brake calipers (2552) and rear disc brake rotors (2C026) .




  1. Clean all dirt from area of axle housing cover with a wire brush and/or cloth.
  1. Drain rear axle lubricant by removing the axle housing cover .
  1. Remove differential pinion shaft lock pin and differential pinion shaft .


    9979cb3.gif
  1. Push flanged end of the axle shafts toward the center of the vehicle and remove the rear axle shaft retaining u-washer from the button end of the axle shaft .



  1. Remove axle shaft from the rear axle housing , being careful not to damage the inner wheel bearing oil seal (1177) and rear brake anti-lock sensor ring.
Installation
NOTE: Check for presence of rear axle shaft o-ring (4A332) on the spline end of the shaft and install if not present.
sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Care must be taken not to let axle shaft splines damage oil seal or bearing assembly.
  1. Carefully slide axle shaft into rear axle housing without damaging rear wheel bearing (1225) or rear brake anti-lock sensor indicator (2C189) . Start splines into side gear and push firmly until the button end of axle shaft can be seen in the differential case .
  1. Install the rear axle shaft retaining u-washer on the button end of the axle shaft splines, then pull the shaft outboard until the shaft splines engage and the rear axle shaft retaining u-washer seats in the counterbore of the differential side gear .
  1. Position the differential pinion shaft through the differential case and differential pinion gears , aligning the hole in the differential pinion shaft with the lock bolt hole. Apply Rear Axle Lubricant to differential pinion shaft lock pin . Install differential pinion shaft lock pin and tighten to 20-41 Nm (15-30 lb-ft). sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Differential pinion shaft lock pin must be tightened to specification using Stud and Bearing Mount E0AZ-19554-BA (WSK-M2G349-A1) or equivalent.




    NOTE: Axle housing cover must be installed within 15 minutes of application of the silicone rubber or new silicone rubber must be applied.
    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure machined surfaces on both axle housing cover and rear axle housing are clean before installing the new silicone sealant. Inside of axle must be covered when cleaning the machined surface to prevent axle contamination. Tighten the cover bolts in a crosswise pattern to ensure uniform draw on axle housing cover .
  1. Apply Silicone Rubber D6AZ-19562-AA or BA (ESB-M4G92-A or ESE-M4G195-A) or equivalent. Install axle housing cover and tighten retaining bolts to 28-38 Nm (38-52 lb-ft).



  1. Add Motorcraft Rear Axle Lubricant XY-90-QL or KL (ESP-M2C154-A) or equivalent until it is 6-14mm (1/4-9/16 inch) below bottom of fill hole. Add 118.3 mL (4 oz) of Ford Additive Friction Modifier C8AZ-19B546-A (EST-M2C118-A) or equivalent to Traction-Lok axles. Install fill plug and tighten to 20-41 Nm (15-30 lb-ft).
  1. Install rear brake anti-lock sensor indicator . Tighten retaining bolt to 4.5-6.8 Nm (40-60 lb-in).
  1. Install rear disc brake caliper and rear disc brake rotor .
  1. Install wheels and tires.
---------------------------------------------------------
  1. Insert Rear Bearing Remover T85L-1225-AH in bore and position it behind bearing so tangs on tool engage bearing outer race. Remove rear wheel bearing and inner wheel bearing oil seal as a unit, using Impact Slide Hammer T50T-100-A.

    Rear Disc Brake Caliper Anchor Plate




  1. Lubricate the rear wheel bearing with Rear Axle Lubricant.



  1. Install rear wheel bearing into the housing bore using Axle Tube Bearing Replacer T78P-1225-A.



    sra~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Installation of rear wheel bearing or inner wheel bearing oil seal assembly without proper tool may result in an early bearing or seal failure. If inner wheel bearing oil seal becomes cocked in bore during installation, remove it and install a new one.
  1. Install the inner wheel bearing oil seal using Axle Tube Seal Replacer T78P-1177-A. Use Premium Long-Life Grease XG-1-C or K (ESA-M1C75-B) or equivalent between the lips of the inner wheel bearing oil seal .



  1. Install axle shafts as outlined.

May 13, 2009 | 2004 Ford Crown Victoria

1 Answer

Bad rear axle bearing with probable damage to inner bearings


If you have a bad bearing than there is probably metal throughout the whole rear end. I would contact a toyota wrecking yard and price a complete rear end for your vehicle. Search online for a toyota wrecking yard in your area. A complete rear end will be around $600 dollars.

Mar 01, 2009 | 1994 Toyota Previa

1 Answer

I have a 91 4 runner that just started making a (hard to describe) periodic buzz/whine sound coming from the right front driveshaft/axle area mostly when 4x4 is disengaged


Neal, it may not be the right front axle. I thought I had the same problem with 97 4Runner but it turned out to be the right rear axle bearing. Even the technican thought the niose was coming from the right front axle when he test drove it with me. Seems those rear bearings go out if you do a lot of towing with the truck. Cost about $ 400.00 to replace make sure they replace the ABS sensor collar and replace the axle breather tube vent ( they get plugged and when they replace the bearing , they have to replace the seal in the axle also and mine leaked after because of a plugged axle vent.

Dec 20, 2008 | Toyota 4Runner Cars & Trucks

3 Answers

2002 ford Ranger 3.0 v6 (auto) rear end noise when accelerating on curves.


Remove the drums and check your rear brakes. If okay, you may try testing a couple different tires in the rear. Belts separating and flat spots show worse at higher speeds.
It could be bearings if truck is used alot while loaded. Remember 1/4 ton is only 500lbs. High miles, hard driving, or if it was wrecked in rear could all cause these smptoms.

Jul 17, 2008 | 2002 Ford Ranger Regular Cab

Not finding what you are looking for?
2004 Suzuki Grand Vitara Logo

530 people viewed this question

Ask a Question

Usually answered in minutes!

Top Suzuki Experts

yadayada
yadayada

Level 3 Expert

75077 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Boyet Soriano
Boyet Soriano

Level 2 Expert

293 Answers

Are you a Suzuki Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...