Question about 1997 Oldsmobile Cutlass Supreme

1 Answer

How do i remove and replace the rear brake/light bulb on my 2006 Seat Altea?

Posted by on

Ad

1 Answer

  • Level 1:

    An expert who has achieved level 1.

    Mayor:

    An expert whose answer got voted for 2 times.

  • Contributor
  • 1 Answer

Open the boot, Undo the 2 big screws... then go inside the boot, open the patch on the side... take out the connector... you should also see a white plastic cylinder... unscrew that... then you should be able to take the whole light out.. once you have... undo the 2 screws where the light bulb is.. and bobs ya uncle. :) by Fiz.

Posted on Sep 26, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

2005 Seat Altea 2.0 XL The ABS light is showing on the Panel from startup to running and switch off how can this be removed as I believe it will not pass the next MOT Thanks


it cannot ,its thats simple .You need to find the fault and fix it as the ABS computer is the only one which will reset itself once the faulty sensor is detected or the magnetic ring on the back of the wheel bearing ,if a 2005 seat then it could have drum brakes on the rear and the dust build up is causing the sensor not to pick up a reading ,if so try removing the rear drums and cleaning the dust out ,if disk brakes on the rear the try this old trick ,use a pressure washer in a garage and wash the backs of the wheels front and back this often clears the muck causing the sensors not to pick up a pulse ,then drive car for ahlf mile and it may go out the light will not go out without a short drive to reset the computer ,check the sensor multiplug connections as well as if a northern europe vehicle the weather leaves a lot to be desired .

Nov 10, 2016 | 2005 Seat Altea 2.0

1 Answer

I need to replace bulb on rear fog light on my 2006 seat altea, please help.


should just be a screw holding the light cover on either at the front or behind bumper then the bulb will just be a bayonet fit

Nov 27, 2013 | Cars & Trucks

1 Answer

How to change the third break light bulb in a 2007 hyundai sonata ?


From 2006 to 2010, the Sonata's 3rd brake lamp requires the rear package deck be removed to access that bulb.
1. Remove the rear passenger seat bottom (remove two12mm bolts between the seat back and the seat bottom - tilt the seat back forward to locate these bolts).
a. Press the two bottom front edge tabs to release the front of the seat bottom from the floor.
b. Remove seat bottom & set aside w/two 12mm bolts
c. Tilt both seat backs downward
2. Remove the left & right hand shoulder cushions (12 mm bolt at the bottom of each cushion)
a. Remove seat belt from shoulder cushion guide at the top of the cushion
b. Lift up and forward on shoulder cushions to remove them (if equipped with side airbags, disconnect wire harness connector).
c. Set shoulder cushions aside w/two 12mm bolts
3. Using a small flathead screwdriver, pop out the 'SRS' button cover from the C pillar panels on the left & right hand side to access either the phillips head screws, 10mm bolts, or #30 Torque Screws
a. Remove screws and set aside
b. Using a standard flathead screwdriver, pop out the C pillar panels on both sides (clips hold these panels in place)
c. Set these panels aside after removal w/screws/bolts
4. Trunk Access-way panels are held in place by phillips head screws (two at the bottom (left and right hand sides) and 4 to 5 at the top .
a. Remove left and right hand panels and set aside w/screws.
5. Rear package deck held in place with two plastic clips (white, yellow or pink)
a. lie on your back inside the trunk (trunk lid open to allow for more light). Looking through access hole find 3rd brake light wire harness connector & disconnect.
b. locate package deck clips, one on the left and another on the right on the underside of the pckage deck
c. Squeeze clips to push them out - package deck will come loose
d. Remove package deck & remove 3rd brake lamp bulb socket (turn counter clockwise to remove). Replace bulb & reassemble in reverse order.

Sep 05, 2011 | Hyundai Sonata Cars & Trucks

1 Answer

2006 Chevy Trailblazer...the top "third"


Brake light problem - if bulbs and fuses (#34 and #43 in rear fuse panel) are good, then only other possibility are the circuit boards where all the tail lights are located.

Noise coming from rear is the mode control actuator in the rear HVAC unit, it is trying to move a stuck blend door.

Aug 06, 2011 | 2006 Chevrolet Trailblazer

1 Answer

Replacing brake light above trunk on 2006 chrysler


This is quite a process....

Removal
1) Disconnect and isolate the negative battery cable.
2) Remove the rear shelf trim panel.

3ca61c4.jpg
3) Disconnect the CHMSL electrical connector (1).

7bde5c5.jpg

4) Remove the two mounting fasteners (3) to the CHMSL (2).

6793725.jpg

Installation is opposite of removal.

Rear shelf trim panel

Removal

1) Disconnect and isolate the battery negative cable.
2) Remover the right and left lower and upper C-pillar trim.
3) Remove the nut that secures the center rear seat belt lower anchor to the stud on the floor panel and feed the seat belt webbing back through the opening in the top of the rear shelf panel trim (2) to the retractor.
4) Remove the push-pin fastener (1) that secures the trim (2) to the rear shelf panel.
5) Slide the trim forward to disengage the S-clip that secures the underside of the trim to the to the center of the shelf panel.
6) Remove the trim from the rear shelf panel.

24614b2.jpg

Installation

1) Position the trim (2) onto the rear shelf panel(3).
2) Slide the rear edge of the trim rearward to engage the lens bezel of the center high-mounted stop lamp and far enough to engage the S-clip that secures the underside of the trim to the center of the shelf panel.
3) Install the push-pin fastener (1) that secures the trim to the rear shelf panel.
4) Pull the center rear seat belt lower anchor and belt webbing from the retractor through the opening the the top of the rear shelf panel trim and back down to the stud on the floor panel.
5) Install and tighten the nut that secures the seat belt lower anchor to the stud on the floor panel. Tighten the nut to 34 N m (25 ft. lbs.).
6) Reinstall the right and left upper and lower C-pillar trim.
7) Connect the battery negative cable.

841a5de.jpg

C-pillar trim removal

1a140ec.jpg

5ad047d.jpg

b674bd4.jpg
cf360b2.jpg

cd4ac09.jpg
2e5b4da.jpg

Seat removal

d276bae.jpg
60b3895.jpg

469e099.jpg

087d2a6.jpg

3ad2dc9.jpg


a09baad.jpg
4981771.jpg


Hope this all gets it done for you........

Feb 23, 2010 | 2006 Chrysler 300

1 Answer

How do I replace rear window brake light


You've got to remove the upper cushions of the back seat to access the screws to allow you slide the parcel shelf forward. $80 labor, $2.00 bulb.

Jan 19, 2010 | 2006 Hyundai Sonata

1 Answer

Replace rear brake light bulb in 2006 Pacifica


You can remove bulb from inside of the baggage cabin, just open the panel behind the rear lamps boc and replace the bulb

Sep 13, 2009 | 2006 Chrysler Pacifica

2 Answers

My high level brake light has bruned out,(third brake light). I was informed by the dealer the back window panel has to be removed to replace the 3.00 dollar bulb, total cost 75.00 dollars. With some


replace the bulb...??? This requires you remove the rear package deck (to access the bulb & socket). to do this, remove the seat bottom (two bolts hold the rear seat bottom to the chassis, then remove the bolts which hold the shoulder cushions (LH & RH - 12mm bolts) then remove the cosmetic molding around the trunk access (7 to 8 screws) then remove the "C" pillar covers (SRS curtain airbag LH & RH) to access the rear deck package & access the third brake lamp bulb. replace it, then reassemble.

May 26, 2009 | 2006 Hyundai Sonata

2 Answers

Hyundai 2006 Sonata high mount brake light.


the rear seat does NOT have to be removed in order to replace the stoplamp and/or its bulb.
you have to get into the trunk, and there are (2) philips screws holding the stoplamp secured to the package tray. the actual process takes about 15 minutes, because to do it right you have to actually get IN the trunk.

the price they charged you sounds about right if the price of the stoplamp is included, dealerships tend to overcharge for parts.

Apr 11, 2009 | 2006 Hyundai Sonata

2 Answers

PT Cruiser Brake Light


The bulb in the rear light has burned out and to replace it follow these instructions: 1) go to your owner's manual to find out the part number. You can find and purchase the replacement bulb at Target, any auto parts store and even at Walmart for under $4.00; 2) pop open the trunk door; 3) get a phillips screw driver and unscrew the 2 screws holding the rear brake light fixture to your car body; 4) as soon as you turn over the fixture you'll see where to pull out the burned out bulb and replace it with the new one(s). Good luck!

Jul 14, 2008 | 2006 Chrysler PT Cruiser

Not finding what you are looking for?
1997 Oldsmobile Cutlass Supreme Logo

3,135 people viewed this question

Ask a Question

Usually answered in minutes!

Top Oldsmobile Experts

yadayada
yadayada

Level 3 Expert

76132 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you an Oldsmobile Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...