Question about 2005 Chevrolet Uplander

1 Answer

2008 chev uplander headlight

Ownersmanual says to pull the pin and ans unscrew the headlight retaining screw and the entire assy is suppose to pull away from the vehicle. it does not want to pull away from the vehicle at all

Posted by on

Ad

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Chevrolet Master
  • 1,564 Answers

You must reach around to the body of the headlight switch and feel for a small round dot about 1/8 inch in diameter. This button is spring loaded and pushes in as you pull on the lightswitch knob, then you must push it a second time to release the knob. Please make sure your battery is disconnected while performing this procedure for the headlights will stay on otherwise. Then remove the retaing collar at the center and the switch will pull "back" from the dash enough to remove the wiring harness. Thank you, Dana

Posted on Jan 30, 2010

Ad

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Ad

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

How to replace the headlights on 96 jimmy


96 had two types of retaining set ups --open hood and behind lens are two locking tabs that has elongated slot with a hole the pin in the elongated slot is what holds light in place [[retaining pin]]pull up till pin is lined up with hole on both and lens falls out so keep a hold of it ----or you have the 2 long skinny bolts down to the lens unscrew them and pull lens forward from truck remove connector and to remove bulb push in and turn 1/4 counterclockwise put in new and and done the following link showes the screw type
96 jimmy headlight Yahoo Video Search Results

Jul 06, 2016 | 1996 GMC Jimmy

1 Answer

How to change headlight on 2007 saturn outlook


i found that you can reach it bye on screwing the fourr 8m bots that hold the inner wheel weld. Once you remove the bolts just pull inner plastic fender away and you will be able to unscrew the outer retainer cup then unscrew bulb housing..

Sep 10, 2011 | 2008 Saturn Outlook

1 Answer

How do I access the H-1 headlamp bulb on drivers side to replace. Is there a retaining screw under the wheelwell for the entire headlamp assembly that must be removed ? Does the airbox and battery have to...


there is a retainer that holds headlight assembly in it a slide you pull up a headlight should come out as an assembly looks like a hook and it slides up

Jan 26, 2011 | 1999 Volkswagen Beetle

1 Answer

Removal of head light assy 1989 ford ranger.


Hello,

To remove the front head light please follow the steps below:
  1. Place the Ford Ranger in "Park." Turn the engine off. Turn the headlights off. Remove the key from the ignition. Allow the truck to cool for about 20 minutes.
  2. Open the hood of the vehicle. Locate the two retainer pins on the headlight assembly of the light that needs to be replaced. Pry the retainer pins open with your finger. This releases the headlight assembly from the Ranger.
  3. Pull the headlight assembly forward. Unplug the electrical connector from the back of the assembly by hand. Rotate the retaining ring counterclockwise and slide it off the plastic bulb base.
  4. Pull the burned out bulb straight out of the headlight assembly. Discard the used bulb. Insert a replacement bulb into the headlight assembly and push it straight into the socket until it clicks into place. Slide the retaining ring around the bulb and rotate it clockwise to secure it.
  5. Plug the electrical connector into the back of the unit. Slide the headlight assembly back into the Ranger. Push the retaining pins back down to secure the headlight assembly.
Hope this helped. thank You for using FixYa!!!

Jan 19, 2011 | 1989 Ford Ranger

1 Answer

How to change headlight fo 2005 chevrolet uplander


Headlamp Removal & Installation Bulb Replacement To Remove:
  1. Remove the Headlamp Assembly. Headlamp bulbs gm-06-00-3206.gif

  2. Turn the high/low beam bulb socket counterclockwise to remove.
To Install:
  1. Turn the high/low beam bulb socket clockwise to install.
  2. Install the Headlamp Assembly.
Headlamp Assembly (Park, Turn, Cornering and Side Marker Lamps) To Remove:
Headlamp assembly R &I gm-06-00-3207.gif

  1. Rotate the headlamp assembly retainer pins and pull up to remove.
  2. Remove the mounting bolts.
  3. Disconnect the harness connectors.
To Install:
  1. Connect the harness connectors.
  2. Position the headlamp assembly on the panel.
  3. Rotate the retainer pins and push down to lock in place.
  4. Install and secure the mounting bolts.
prev.gif next.gif

Oct 07, 2010 | 2005 Chevrolet Uplander

1 Answer

Need to remove and repair headlight motor on a 1988 corvette


REMOVAL & INSTALLATION 1984–88 Vehicles
  1. Open the hood, then turn the headlights on.
  2. Detach the headlight motor wire on the outer side of the headlight.
  3. Turn the headlights off (the disconnected light should stay open).
  4. Unfasten the 4 screws at the bezel. There are 2 at the front and 2 at the sides. Fig. 1: With the hood in the raised position, unfasten the Torx® screws from the outer side of the headlight bezel/trim piece 91036p23.jpg
    Fig. 2: You must then remove the screws from the inner side of the bezel/trim piece 91036p24.jpg

  5. Remove the bezel. Fig. 3: Remove the first of the top bezel/retaining ring screws . . . 91036p25.jpg
    Fig. 4: . . . then remove the remaining Torx® screw 91036p26.jpg
    Fig. 5: Lift the bezel/trim piece away from the headlight assembly 91036p27.jpg

  6. Remove the retaining spring by carefully using a hooked end tool, such as a cotter pin removal tool to move it to the side.
  7. Remove the headlight from the aiming pins by rotating the headlight toward the center of the car.
  8. Unfasten the 4 retaining ring screws, then remove the ring. Fig. 6: With the hood closed, you can see the 4 headlight retaining ring screws (1) and 2 aiming screws (2) 91036p28.jpg
    Fig. 7: Remove ONLY the 4 retaining ring screws, do NOT touch the aiming screws 91036p29.jpg

  9. Remove the headlight pump from the mounting bracket, unplugging the socket as you pull it away. Fig. 8: Remove the headlight away from the mounting bracket, unplugging the socket as you pull it away 91036p30.jpg
    To install:
  10. Install the headlight bulb, making sure it is plugged in properly.
  11. Position the retaining ring and secure with the 4 screws.
  12. Position the headlight into the aiming pins. Move the retaining spring back into place.
  13. Install the bezel and secure with the retainers.
  14. Turn the headlights on, then connect the headlight motor wire.
  15. Turn the headlights off. Both should lower.
  16. Close the hood. Check the aim of the headlights, and adjust if necessary.
1989–96 Vehicles
  1. Open the hood.
  2. Open the headlight door halfway. This can be done either by turning the headlight switch on, then back to the parking lamp on position, or by the manual headlamp control knob (which is located on the inboard side of the headlight door). NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
  3. Remove the screws from the front of the headlight bezel. NOTE: Before removing the screws from the side of the headlight bezel, place your hand under the bezel to support and prevent damage to it.
  4. Remove the Phillips head screws from each side of the headlight bezel.
  5. Remove the bezel by pulling it straight out from the engine side of the hood. Fig. 9: View of the headlight bezel mounting 91036g28.gif

  6. Unfasten the screws from the headlight retaining ring.
  7. Remove the headlamp from the assembly, unplugging the electrical connector as you are pulling it away. Fig. 10: Exploded view of the headlight assembly 91036g29.gif
    Fig. 11: Location of the headlight mounting and aiming screws 91036g30.gif
    To install:
  8. Attach the headlight electrical connector.
  9. Position the retaining ring and install the screws securing the ring to the headlight.
  10. Position the bezel in place on the headlight assembly.
  11. Install the screws on each side of the bezel and tighten to 51 inch lbs. (5.8 Nm).
  12. Install the screws on the front of the bezel and tighten to 17 inch lbs. (1.9 Nm).
  13. Cycle the headlamps, then close the hood. Check the headlight aim, and adjust if necessary.
prev.gif next.gif

Jul 07, 2010 | 1988 Chevrolet Corvette

1 Answer

Replace headight assembly on 2005 buick lacrosse


The procedure to replace head light assembly on buick lacrosse is as follows:--- 1)To remove and replace the headlight assembly you will need to remove 1 retaining bolt on the top of the headlamp assembly and 2 sliding retainers at the rear. 2) The carefully Pull up the retainers and that will release the headlight assembly and allow you to pull it out the front. 3) When installing the new headlight assembly make sure you have it lined up correctly before trying to install the retainers, don't force them it may get cracked . 4) Both the cover and the bulb are removed by a standard twist to the counterclockwise and replaced by a twist to the clockwise. 5) Now to the dim light. You have to release the entire light assembly before you can remove the screw-on cover to reach the light. 6) On the rear edge of the light unit closest to the engine is a white locking tab. Pull that tab up just to the point where it releases…pull too far and it locks again. 7) Next, locate the other locking bracket which is a metal bracket in the center-rear of the light assembly. This bracket is held down by a screw. 8) Remove the screw with a 10mm wrench. Lift the bracket just like you did the white bracket. You should now be able to pull (or pry) the entire light unit forward a little. Depending on the size of your hands this might be enough. Note:-- The turn signal is part of the headlight assembly on your 2005 Buick LaCross. 9) To replace the headlight bulb you need to remove the front bumper cover. 10)To release the plastic bumper assembly to give you a little more space. This is done by removing two expansion locking pins, one that holds the little plastic strip down between the bright and dim lights and one that is located inside a rubber bumper on the engine side of the light unit. 11)To remove these locking pins, pull or pry up the little tab in the center of the pin. Thanks.

May 23, 2010 | 2005 Buick LaCrosse

1 Answer

Need picturss on how to change headlights for 2005


if you have a owners manual its in there, if not there is a pin and a screw on top on headlight assm. you take out and assm. pulls out to access headlight and turn signal bulbs.

Oct 13, 2009 | 2005 Chevrolet Uplander

1 Answer

Fender bender, bought new assembly. How to remove old for replacement? "89 seville driver side headlight.


LIGHTING Headlights REMOVAL & INSTALLATION
  1. Unscrew the Torx retaining screws and remove the headlight bezel.
  2. Remove the headlight bulb retaining screws. These are the screws which hold the retaining ring for the bulb to the front of the car. Do not touch the two headlight aiming screws, at the top and the side of the retaining ring (these screws will have different heads), or the headlight aim will have to be re-adjusted.
  3. Pull the bulb and ring forward, then separate them. Unplug the electrical connector from the rear of the bulb.
  4. Plug the new bulb into the electrical connector. Install the bulb into the retaining ring and then install the ring and the bulb. Install the headlight beze

Aug 23, 2009 | 1989 Cadillac Seville

Not finding what you are looking for?
2005 Chevrolet Uplander Logo

342 people viewed this question

Ask a Question

Usually answered in minutes!

Top Chevrolet Experts

yadayada
yadayada

Level 3 Expert

76164 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22156 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

8273 Answers

Are you a Chevrolet Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...