Question about 2001 Buick Regal
/* Style Definitions */
mso-padding-alt:0in 5.4pt 0in 5.4pt;
font-family:"Times New Roman";
EXHAUST GAS RECIRCULATION (EGR) VALVE REPLACEMENT
REMOVAL PROCEDURE 1. Turn OFF the ignition. 2. Disconnect the EGR valve electrical connector 3. Remove the bolt retaining the pipe assembly from the EGR valve and carefully pull the pipe assembly back. 4. Remove the EGR valve retaining bolts. 5. Remove EGR valve assembly. 6. Remove the gasket. INSTALLATION PROCEDURE
Install the EGR Valve with a new gasket to the intake manifold. NOTE: Refer to Fastener Notice in Service Precautions. 2. Install the bolts through the EGR valve. Tighten Tighten the bolts to 30 N.m (22 lb ft) 3. Connect the pipe assembly to the EGR valve. 4. Install the bolt. Tighten Tighten the bolts to 30 N.m (22 lb ft) . Connect the EGR valve electrical connector.
Posted on Jan 30, 2010
A 6ya expert can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
The service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
Posted on Jan 02, 2017
SOURCE: Location of EGR Valve
Found the info!!
This Dodge EGR valve is a certain kind of device that is mounted right on your intake manifold which controls the amount of exhaust gasses back into your engine.
On a 2005 Dakota with 4.7 liter engine (non-HO), the EGR valve is located near the intake manifold on the driver's side right up against the firewall. It's hard to spot as it sits lower than the intake manifold. To change it, remove the electrical connector. There's a red tab that needs to be pushed to one side and then you have to squeeze down on a tab to get it free. Using a 13 mm socket, remove the bolt that you can see. I had to use a 3 inch wobble extention and then a 8 inch extension with a deep well socket to reach it with my 3/8 inch ratchet. There's a second bolt that you can't see between the EGR valve and the firewall. With a little trial and error and a lot more luck, you can reach the hidden bolt with the 3 inch wobble extension and a 13 mm deep well socket. Attach the ratchet after the socket is on and remove. This one isn't easy and if there's any Dodge engineers reading this one, a couple of extra inches of clearance between the valve and the firewall wouldn't have killed you no matter what the cost accountants said. With both bolts removed, you should be able to pull out the metal pipe that connects the manifold to the EGR valve out of the manifold (Pull to the right) and then you can lift the valve out. For assembly, the metal pipe connecting the intake manifold the EGR valve has to be removed and reinstalled on the new valve. It's held on with 2 5/16th" bolts. You should put the rear bolt on tight, but leave the front bold loose for the reinstall as some adjustment is necessary to get it put back together and the rear is a pain to tighten when installed. Line up the bolts that attach the valve and get the rear 13 mm bolt (The one you couldn't see on disassembly) started. Do not start the other 13 mm bolt as you'll need to pivot the valve and pipe to the left in order to reinsert the pipe into the intake manifold. Once the pipe is in the intake manifold. Start the other 13 mm bolt and tighten both 13 mm bolts and then the 5/16" bolts holding the pipe onto the valve. Reinstall the electrical connection. Please don't forget to rate!!!!
Posted on Mar 14, 2009
The electronic EGR valve and solenoid assembly is attached to the rear of the left cylinder head ,
Posted on Feb 05, 2009
SOURCE: egr valve location
The EGR Valve Location is typically housed on the intake manifold this schematic may help you
Posted on Mar 07, 2009
SOURCE: EGR Sensor/valve replacement
The EGR is a three part series; the valve, soleniod, and sensor. They are fairly easy to change, a few hours with a buddy. They are located on the top back, center of the engine. Take a look you will see something that is small and cylinder like with a wire connected to the top, that is the vavle. I would replace all three at once as they are all together and you have to take of one to take of the others. The total price will cost you about $250 in parts. However, you must know your engine type on the Sable/Tarus as the parts are different per engine.
Posted on May 02, 2009
The EGR, or exhaust gas recirculation valve, takes inert exhaust gasses
drawn from the exhaust system and reintroduces them into the combustion
chamber through the intake manifold. This process lowers the peak
combustion temperature and helps combat the formation of Nitrous Oxide
(NOx) in the exhaust.
Posted on Sep 07, 2009
Tips for a great answer:
Mar 08, 2016 | 2003 Pontiac Aztek
Dec 13, 2015 | Cars & Trucks
Apr 30, 2014 | Cars & Trucks
Mar 14, 2012 | 1991 Ford F150
Feb 07, 2012 | 2000 Mercury Sable
Aug 09, 2011 | Chevrolet HHR Cars & Trucks
Nov 25, 2009 | 1997 Toyota Camry
Nov 22, 2009 | 1993 Saturn SC2
Feb 05, 2009 | 2005 Dodge Ram 1500
1,664 people viewed this question
Usually answered in minutes!