Question about 1988 Mitsubishi Pickup

1 Answer

How do i replace the front brake disc on l200 4 door pick up 02MY

Posted by on

1 Answer

  • Level 3:

    An expert who has achieved level 3 by getting 1000 points

    All-Star:

    An expert that got 10 achievements.

    MVP:

    An expert that got 5 achievements.

    President:

    An expert whose answer got voted for 500 times.

  • Mitsubishi Master
  • 2,030 Answers

Remove the wheel
Take out the caliper bolts
press piston back into caliper with a brake tool or c-clamp
put new pads in
replace caliper
replace wheel
PUMP BRAKES UP MANY TIMES TO SEAT PADS
Your Done

Posted on Jan 30, 2010

1 Suggested Answer

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya expert can help you resolve that issue over the phone in a minute or two.
best thing about this new service is that you are never placed on hold and get to talk to real repairmen in the US.
the service is completely free and covers almost anything you can think of (from cars to computers, handyman, and even drones).
click here to download the app (for users in the US for now) and get all the help you need.
goodluck!

Posted on Jan 02, 2017

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Hello, I am hearing a humming/grinding sound when I accelerate my vehicle. It only starts once the car gets going. Idle the car in fine. I am not sure if it has anything to do with my tires/axles. I...


Check your disc brake pads to see if they are down to the wear indicaters. When brakes are worn it creates a metal on metal grinding sound when vehicle picks up speed but will intermittenly stop when pressure is applied to brakes. Note that front brakes will be replaced 2 to 3 times more often than back brakes due to the front brakes being your primary souce of stopping power.

Apr 05, 2011 | 2006 Chevrolet Impala

1 Answer

Front disc brake assembly diagram


SECTION 206-03: Front Disc Brake 1999 Escort/Tracer Workshop Manual DESCRIPTION AND OPERATION Procedure revision date: 06/06/1998 Front Disc Brake Front Disc Brake System Components
Item Part Number Description 1 1125 Front Disc Brake Rotor 2 2B296 Disc Brake Caliper Locating Pin 3 2B120 Disc Brake Caliper 4 2001 Brake Pads 5 - Copper Washers (2 Req'd) 6 - Banjo Bolt 7 2078 Front Brake Hose 8 2W303 Brake Caliper Bolt- (2 Req'd) 9 2814 Brake Hose Clip The front disc brake system consists of a single-piston front disc brake caliper (2B120) and a ventilated front disc brake rotor (1125). The brake shoes and linings (2001) are held in the front disc brake caliper by two front disc brake caliper locating pins (2B296) and two springs. The inboard brake shoe and lining is equipped with a wear indicator that makes a squealing noise when the brake shoes and linings are worn beyond recommended use.

2010&c18=modelyear&c20=n41287&c35=wsm%2cfront%20disc%20brake%2csxf%2c206-03%2cdescription%20and%20operation&s=1366x768&c=32&j=1.3&v=y&k=y&bw=995&bh=428&ct=lan&hp=n&[aqe] ddll111_28.gif

Dec 15, 2010 | 1999 Mercury Tracer

1 Answer

How do you get the capierer pin off to put front brake pads on my Mercury Sable LS?


Section 06-03: Brakes, Front Disc 1999 Taurus, Sable Workshop Manual REMOVAL AND INSTALLATION Brake Shoe and Lining Removal
  1. Remove brake master cylinder filler cap (2162). Check fluid level in brake master cylinder reservoir (2K478) . Remove brake fluid until brake master cylinder reservoir is half full. Discard removed fluid.
  1. Raise vehicle on hoist.
  1. Remove wheel and tire assembly from front disc brake rotor mounting face. Use care to avoid damage or interference with disc brake caliper (2B120) , front disc brake rotor shield (2K004) or front wheel knuckle (3K185) .
  1. Remove rear brake pin retainers (2N386).
  1. NOTE: It is not necessary to disconnect hydraulic connections.

    Lift disc brake caliper from front disc brake caliper anchor plate (2B292) and front disc brake rotor (1125) . Do not pry directly against metal caliper piston or damage will occur.
  1. NOTE: To prevent damage, do not allow disc brake caliper to hang by the front brake hose (2078) .

    Position disc brake caliper out of the way.
  1. Remove inner outer brake shoe and lining (2001) assembly from front disc brake caliper anchor plate .
  1. Inspect both rotor braking surfaces. Minor scoring or buildup of lining material does not require machining or replacement of front disc brake rotor.
-----------------------------------------------------------------
remove the 2 pins, #10 in pic. Usually has a dust cover over pin accessopening. Usually torx haed or hex head bolts (pins).


snorkelbobby_7.gif

Nov 12, 2010 | 1999 Mercury Sable

1 Answer

What tools needed to replace front brake pads & rotors


Brake Pads
Removal & Installation
Front





3.4L front disc brake assembly
toy_4run_34_frontbrakeassembly.gif








4.0L and 4.7L front disc brake assembly
toy_4run_frontbrakeassembly.gif



To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Clip, 2 caliper pins, the anti-rattle spring then remove the 2 brake pads
      and the 4 anti-squeal shims

To Install:

CAUTION
Only replace brake pads on 1 side of the
vehicle at a time. Failure to use this procedure could cause the caliper pistons
on the opposite side of the vehicle to pop out requiring the reconditioning or
replacement of the brake caliper.


  1. Remove a small amount of brake fluid from the master cylinder.
  2. Install a used brake pad into the caliper and compress the caliper pistons.
  3. Apply disc brake grease to both sides of the inner anti-squeal shims.
  4. Install or connect the following:

    • Anti-squeal shims to the new brake pads
      NOTE: When replacing worn pads, the anti-squeal shims must be replaced
      together with the pads.

    • 2 brake pads
    • Anti-rattle spring and the 2 caliper pins
    • Clip
    • Front wheel

  5. Depress the brake pedal several times to seat the brake pads.
  6. Check the brake fluid level and top off as needed.

Rear
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Rear wheel






      toy_4run_rearcalbolts.gif



    • 2 cylinder slide pins from rear caliper assembly
    • Caliper assembly from rear caliper mounting
    • 2 brake pads with anti-squeal shims from rear caliper mounting
    • 2 anti-squeal shims from each disc brake pads
    • Pad wear indicator plate from the inner side disc brake pad
    • 4 pad support plates from the rear caliper mounting

To Install:


  1. Install or connect the following:

    • 4 pad support plates on the rear caliper mounting
    • Pad wear indicator plate on the inside brake pad
      Note: Install the pad wear indicator facing downward.

    • Anti-squeal shims on each brake pad
    • 2 disc brake pads with anti-squeal shims to the caliper assembly

  2. Apply lithium soap base glycol grease to the sliding part of 2 caliper slide
    pins.
  3. Install or connect the following:

    • Disc brake caliper assembly with 2 caliper slide pins
    • Torque to 65 ft-lbs (88 Nm)
    • Rear wheel

  4. Depress the brake pedal several times to seat the brake pads.
  5. Check the brake fluid level and top off as needed.
--- Removal & Installation
Front
To Remove:


  1. Before servicing the vehicle, refer to the precautions in the beginning of
    this section.
  2. Remove or disconnect the following:

    • Front wheel
    • Front brake caliper assembly

  3. Make matchmarks on the disc and the axle hub.
  4. Remove the front disc.

To Install:


  1. Align matchmarks and disc onto axle hub.
  2. Install or connect the following:

    • Front brake caliper assembly with the 2 bolts

      1. Torque to 90 ft-lbs (123 Nm)

    • Front wheel

Sep 23, 2010 | 2003 Toyota 4Runner

1 Answer

How do you replace the front brake caliber on a 1997 ford expedition


Caliper Removal
  1. svj~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Do not use heat to loosen a seized lug nut . Heat can damage the wheel and the wheel bearings.
    Loosen the lug nuts.
    1. Remove the center cap.
    1. With the weight of the vehicle on the wheels, loosen the lug nuts.
      1. svj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: THE ELECTRICAL POWER TO THE AIR SUSPENSION SYSTEM MUST BE SHUT OFF PRIOR TO HOISTING, JACKING OR TOWING AN AIR SUSPENSION VEHICLE. THIS CAN BE ACCOMPLISHED BY TURNING OFF THE AIR SUSPENSION SWITCH LOCATED IN THE RH KICK PANEL AREA. FAILURE TO DO SO MAY RESULT IN UNEXPECTED INFLATION OR DEFLATION OF THE AIR SPRINGS WHICH MAY RESULT IN SHIFTING OF THE VEHICLE DURING THESE OPERATIONS.
        Raise and support the vehicle.
      1. Remove the wheel and tire assembly.
        1. Remove the lug nuts.
        1. Remove the wheel and tire assembly.
      2. CAUTION: Replace the lining if worn to or past specifications. Replace the brake shoes and linings in complete axle sets. Inspect the brake shoes and linings for wear or contamination.
      3. svj~us~en~file=ani_caut.gif~gen~ref.gif WARNING: BRAKE FLUID CONTAINS POLYGLYCOL ETHERS AND POLYGLYCOLS. AVOID CONTACT WITH EYES. WASH HANDS THOROUGHLY AFTER HANDLING. IF BRAKE FLUID CONTACTS EYES, FLUSH EYES WITH RUNNING WATER FOR 15 MINUTES. GET MEDICAL ATTENTION IF IRRITATION PERSISTS. IF TAKEN INTERNALLY, DRINK WATER AND INDUCE VOMITING. GET MEDICAL ATTENTION IMMEDIATELY.
        Disconnect the front brake hose (2078).
        1. Remove the front brake hose bolt.
        1. Remove the copper washers. Plug the front brake hose.
        1. Disconnect the front brake hose
      4. Remove the disc brake caliper (2B120).
        1. Remove the two caliper bolts.
        1. Lift the front disc brake caliper (2B121) off the front disc brake caliper anchor plate.
      5. On 4x2 vehicles, measure the front disc brake hub and rotor (1102) thickness.
        • Replace the front disc brake hub and rotor if not within specifications 27.7mm Min.
      6. On 4x4 vehicles, measure the front disc brake rotor thickness.
        • Replace thhe front disc brake rotor if not within specifications. 27.7mm Min.
      7. Inspect the disc brake caliper for leaks.
        • If leaks are found, disassembly is required

Mar 10, 2010 | 1997 Ford Expedition

2 Answers

2001 brake pad replacement 2001 nissan quest


The hard part is pressing the caliper piston abck into the caliper so you can get the new, thicker pads over the rotor. A large C Clamp works best.

SECTION 206-03: Front Disc Brake 2001 Villager Workshop Manual
REMOVAL AND INSTALLATION Pads —Front Disc Brake Removal
  1. Remove the wheel and tire assembly. For additional information, refer to Section 204-04 .
  1. Remove the front disc brake caliper bolts. torx bit. T20?
  1. Support the front disc brake caliper from the front strut and spring assembly using mechanics wire.
  1. Remove the front disc brake pads.
    1. Remove the outboard front disc brake pad.
    1. Remove the inboard front disc brake pad.
Installation
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif CAUTION: Make sure the master cylinder reservoir does not overfill and spill brake fluid while retracting the front disc brake caliper piston.
    NOTE: It is necessary to fully retract the front disc brake caliper piston in the bore before installing the front disc brake pads.
    Install the front disc brake pads.
    1. Install the inboard front disc brake pad.
    1. Install the outboard front disc brake pad.
Caution. The outer pads are left and right. put left on driver side.
  1. Position the front disc brake caliper on the front-wheel knuckle and install the brake caliper pin bolts.
  1. s1v~us~en~file=ani_caut.gif~gen~ref.gif WARNING: It is necessary to depress the brake pedal several times to position the front disc brake caliper piston before driving the vehicle.

Apr 23, 2009 | 2001 Nissan Quest

1 Answer

88 ford t-bird


Hello, pick up a Haynes Repair manual from most auto stores or library. Front brakes are disc, rear are drum unless you have a Turbo. You will need a large adjustable C-clamp to compress the front caliper piston and a standard Brake Tool, spoon, & spring remover for the rear. The rear is complex so only replace one side at a time, using the other side as a map. The front caliper has 2 torx bolts holding it in place. They are mounted on the inside of the steering knuckle and are LH threads. Be sure to crack open the
bleeder valves. Drums will need (always) to be turned at a parts store. Disc may or may not have to be turned or replaced. If you press your brakes and you felt a shake in the steering then the rotors are warped. Rotors can only be turned once, or they become thinner then specs allow. Hope this helps...Dave

Dec 08, 2008 | 1988 Ford Thunderbird

3 Answers

Breaks


Your 89 Corolla has drum brakes at the rear.
The graciousness of a FIxYa rating would be greatly appreciated.

Nov 10, 2008 | 1989 Toyota Corolla 2 Door

Not finding what you are looking for?
Cars & Trucks Logo

682 people viewed this question

Ask a Question

Usually answered in minutes!

Top Mitsubishi Experts

yadayada
yadayada

Level 3 Expert

75197 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22095 Answers

Jeff Turcotte
Jeff Turcotte

Level 3 Expert

7782 Answers

Are you a Mitsubishi Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...