Question about 1999 Ford Expedition

1 Answer

How do i take th fan off my 1999 ford expedition 5.4L engine

Posted by on

Ad

1 Answer

  • Level 2:

    An expert who has achieved level 2 by getting 100 points

    MVP:

    An expert that gotĀ 5 achievements.

    Governor:

    An expert whose answer gotĀ voted for 20 times.

    Hot-Shot:

    An expert who has answered 20 questions.

  • Expert
  • 108 Answers

Remove the radiator fan shroud this is done by removing first the lower piece.unscrew the 2 screws pull it down next remove the other half by removing the two small bolts found at the corner of the radiator.pull up the shroud use a no. 34/36 open combination wrench.you may use a hammer to apply an impact force since it is a clutch fan it rotates on both directions

Posted on Jan 30, 2010

Ad

2 Suggested Answers

6ya6ya
  • 2 Answers

SOURCE: I have freestanding Series 8 dishwasher. Lately during the filling cycle water hammer is occurring. How can this be resolved

Hi,
a 6ya Mechanic can help you resolve that issue over the phone in a minute or two.
Best thing about this new service is that you are never placed on hold and get to talk to real repair professionals here in the US.
click here to Talk to a Mechanic (only for users in the US for now) and get all the help you need.
Goodluck!

Posted on Jan 02, 2017

Ad
emissionwiz
  • 77514 Answers

SOURCE: i ha myd 1999 ford

Hello
You can't program new keys at home after installing a completely new cylinder, you must have two one working keys to do the key programming procedure, To program the anti-theft system will now require you have the truck towed to the dealer. I am a Ford dealer technican and know this all to well. Below is the factory procedure for programming additional keys which only applies two working key. From the service manual:

To program a new Secure Lock ignition key yourself, you will need

two previously programmed Secure Lock keys (keys that already

operate your vehicle's engine). If two previously programmed

Secure Lock keys are not available (one or both of your original keys

were lost or stolen), you must bring your vehicle to your dealership to

have the spare Secure Lock key(s) programmed.

Procedure to program spare Secure Lock keys to your vehicle

New Secure Lock keys must have the correct mechanical key cut for

your vehicle.

Conventional (non-Secure Lock) keys cannot be programmed to your

vehicle.

You will need to have two previously programmed Secure Lock keys and

the new unprogrammed Secure Lock key readily accessible for timely

implementation of each step in the procedure. Please read and

understand the entire procedure before you begin.

1. Insert the first previously programmed Secure Lock key into the

ignition and turn the ignition from OFF to RUN (maintain ignition in

RUN for at least one second).

2. Turn ignition to OFF and remove the first Secure Lock key from the

ignition.

3. Within five seconds of turning the ignition to OFF, insert the second

previously programmed Secure Lock key into the ignition and turn the

ignition from OFF to RUN (maintain ignition in RUN for at least one

second but no more than 5 seconds).

4. Turn the ignition to OFF and remove the second Secure Lock key

from the ignition.

5. Within 10 seconds of turning the ignition to OFF, insert the

unprogrammed Secure Lock key (new key/valet key) into the ignition

and turn the ignition from OFF to RUN (maintain ignition in RUN for at

least one second). This step will program your new Secure Lock key.

6. To program additional Secure Lock key(s), repeat this procedure from

step 1.

If the programming procedure was successful, the new Secure Lock

key(s) will start the vehicle's engine. The theft indicator (located on the

instrument panel) will light for three seconds and then go out.

If the programming procedure was not successful, the new Secure Lock

key(s) will not operate the vehicle's engine. The theft indicator will flash

on and off. Wait at least one minute and then repeat the procedure from

step 1. If failure repeats, bring your vehicle to your dealership to have

the spare Secure Lock key(s) programmed.

Posted on Apr 04, 2011

Add Your Answer

Uploading: 0%

my-video-file.mp4

Complete. Click "Add" to insert your video. Add

×

Loading...
Loading...

Related Questions:

1 Answer

Where is the fan motor for a 1999 ford expedition?


Hvac blower motor is behind the glove box

Nov 28, 2016 | 1999 Ford Expedition

1 Answer

1999 Ford Expedition


99 and 02 have different motor 5.4-4.6 some early model have the same size engine check 02 for its size and 99 if they are the same you will only have to change the platinum..

Apr 15, 2014 | Ford Expedition Cars & Trucks

1 Answer

I have 1998 epxpedition my engine light is on truck run rough ,I t is saying the number cyl is miss firing I need to know what is the firing order on the expo it is a 5,4l. I think it may be the ignition...


a factory weatherstripping on the hood leaks causes the cylinders 2 &3 on the pass side to misfire. pull the coils for the cyl. .take off boot with long spring inside, thats your plug wire. they are rusty, no? clean them up, put some dielectric grease all over the spring and reassemble. theres your prob!!!!

Dec 10, 2010 | 1998 Ford Expedition

2 Answers

Removed spark plug wirers need firing order Ford Expedition 1999


Several engine sizes there...

1999 Ford Expedition 4.6 liter SOHC V-8 VIN "6"

895ec6a.gif



1999 Ford Expedition 4.6 liter SOHC V-8 VIN "W"

54be969.gif



1999 Ford Expedition 5.4 liter SOHC V-8 VIN "L"

b6523b8.gif


Hope this help to solve it (remmeber comment and rated this).

Apr 20, 2010 | 1999 Ford Expedition

1 Answer

1999 Ford Expedition XLT will not start


My ford expedition 99 has service engine soon light on. Hooked up to ODB and the equipment showed nothing; no power; checked on different car worked fine. what is cause. Equipment has worked on another ford expedition before by the way.

Jul 30, 2009 | 1999 Ford Expedition

1 Answer

1999 Ford Expedition new engine uses twice as much gas


Engine is still tight.After being run in, it should be the same fuel consumtion

Jun 28, 2009 | 1999 Ford Expedition

1 Answer

Over drive light on shifter blinks and check engine light is lit.


You need to have it scanned for codes. The flashing overdrive light means it has trouble codes that pertain to the transmission.

May 23, 2009 | 1998 Ford Expedition

1 Answer

1999 expedition overheating


Sometimes fords can be tricky. Try to be sure that all of the air is purged from the system. I usually do this with a manual release cap. run the engine then slowly release the pressure. then the system will stabilize. If that doesn't help then you may have something restricting flow inside the water jackets through the engine. some shops have those nifty little cameras that they can run through the system to look for potential problems. hope it works out for you. I know how how much of a pain some of these problems can be. Good luck.

Apr 22, 2009 | 1999 Ford Expedition

2 Answers

2000 Ford Expedition Overheating


this may be a cluster,wiring or sending unit problem.ask your dealer how hot the engine was getting,with a scanner they can tell what temp the coolant is at.yes your temp gague is rising but is the engine even overheating ?

Nov 05, 2008 | 1999 Ford Expedition

Not finding what you are looking for?
1999 Ford Expedition Logo

Related Topics:

337 people viewed this question

Ask a Question

Usually answered in minutes!

Top Ford Experts

yadayada
yadayada

Level 3 Expert

77499 Answers

Colin Stickland
Colin Stickland

Level 3 Expert

22306 Answers

fordexpert

Level 3 Expert

5626 Answers

Are you a Ford Expert? Answer questions, earn points and help others

Answer questions

Manuals & User Guides

Loading...