How do I get to the front side turn signal bulb to replace it? There is a screw I removed but the yellow lens felt like it would break if I popped it out.

Check this procedure for Signal and Marker Lights...


REMOVAL & INSTALLATION
Front Turn Signal and Parking Lights
1991-96 models
(see Figures 1, 2, 3 and 4)

1. Remove the lens upper retaining screw and the fender side retaining screw.
2. Slide the lens assembly forward until access to the rear is possible.
3. If necessary, unplug the bulb electrical connection.
4. Turn the bulb socket assembly counterclockwise and remove it from the lens.
5. Depress and twist the bulb approximately 1 / 8 turn counterclockwise, then remove it from the socket.
   

Fig. 1: Remove the lens upper retaining screw and the fender side retaining screw

Fig. 2: If necessary, unplug the bulb's electrical connection

Fig. 3: Turn the bulb socket assembly counterclockwise and remove it from the lens

Fig. 4: Remove the bulb from the socket

To install:

1. Align the bulb's locating pins, then install the bulb in the socket.
2. Attach the socket to the lens and turn it clockwise to engage it.
3. If removed, attach the bulb electrical connection.
4. Place the lens into position, then tighten the fender side and upper retaining screws.

Hope this helps.

you need to remove the front turn signal lens to gain access to the bulbs.4 screws

Bi-Xenons - 6000K D1S
High Beams - Osram Nightbreakers H7
Fogs - PIAA H11 Yellow Ion
Cornering Lights - Osram Nightbreakers H3
Front Park Lights - High-Powered LEDs with built-in resistors
Front Signal Lights - Sylvania Silverstar 7507A ST (Silver Bluish but lights up Amber)
Front Sidemarkers - InviSilver W5W (Silver but lights up Amber)
Rear Signal Lights - P21W Stealth Bulbs (Silver but lights up Amber)
Reverse Lights - Sylvania Silverstar 7506ST or Error-Free LEDs
License Plate Lights - C5W Error-Free High-Powered LEDs

Turn the engine off and approach the side of the porsch with the burn-out side-marker light. If you are replacing both, start at either side; the replacement procedure is the same.

2 Remove the screws from the plastic fender liner. Peel back the liner to access the area behind the fender.

3 Reach your hand inside to gain access to the side-marker light's backing. Push the backing forward to release the side-marker lens; it's held in place by small clips.

4 Grab the lens on the outer side and turn it over to access the back. Gently turn the bulb to release it from the plastic lens.

5 Pull the bulb straight out to remove it from the electrical socket. Insert a new bulb, but do not touch the glass part of the bulb with your hand.

6 Push the new bulb into the side-marker lens. Turn it clockwise to install it. Push the side-marker lens back into place. Apply gentle pressure to the lens to pop it back into its mount.

7 Replace the screws along the edge of the fender liner.

Signal and Marker Lights
REMOVAL & INSTALLATION
Front Turn Signal and Parking Lights
1991-96 MODELS

1. Remove the lens upper retaining screw and the fender side retaining screw.
   
2. Slide the lens assembly forward until access to the rear is possible.
   
3. If necessary, unplug the bulb electrical connection.
   
4. Turn the bulb socket assembly counterclockwise and remove it from the lens.
5. Depress and twist the bulb approximately 1?8 turn
   counterclockwise, then remove it from the socket.
   
   
   
   
   
   Fig. 1: Remove the lens upper retaining screw and the fender
   side retaining screw
   
   
   
   
   
   
   
   Fig. 2: If necessary, unplug the bulb's electrical connection
   
   
   
   
   
   
   
   Fig. 3: Turn the bulb socket assembly counterclockwise and remove it from the lens
   
   
   
   
   
   
   Fig. 4: Remove the bulb from the socket
   
   
   To install:
   
   
6. Align the bulb's locating pins, then install the bulb in the socket.
   
7. Attach the socket to the lens and turn it clockwise to engage it.
   
8. If removed, attach the bulb electrical connection.
   
9. Place the lens into position, then tighten the fender side and upper
   retaining screws.

Open the hood, remove the screws to the lens, pull out lens. Then take the bulb socket and turn it, then it will pull out. Then push in and turn bulb unitl it pops out so you can replace it.

remove the mounting screw on the lens, then remove the top 2 bolts holding the headlamp, pull headlamp out to gain access to the mounting nut on the turn signal. Remove the nut and the turn signal light will pull straight out allowing you to replace the bulb.

Front Turn Signal & Parking Lights



Remove the 2 parking light housing retaining screws ...



... then pull the housing away from the vehicle far enough to remove the bulb socket from behind the housing. Turn the socket counterclockwise and pull



Push the bulb in the socket gently and turn clockwise, then pull the bulb out of the socket. Note the offset retaining ears on each side of the bulb

1. Remove the screws from the lens and separate the lens from the headlight bezel.
   
2. Remove the headlight bezel.
   
3. Remove the screws from the turn signal housing and pull it out.
   
4. Turn the bulb socket counterclockwise 1/3 turn and remove it.
   
5. Installation is the reverse of removal.
   

Side Marker Lights

1. Remove the screws from the marker lens and separate the lens from the headlight bezel.
   
2. Pull the bulb from its socket in the back of the lens.
   
3. Installation is the reverse of removal.
   

only i could replace mine where to remove clips from the black wheel well cover then the light bulb un screws from the back of the lens

look at the turn signal lens, see if there are screws holding them, if they are, remove the screws and remove the signal light assembly, after removing, you can replace the bulb by removing the socket at the back of the lens assembly.

tnx 4 using fixya,

drcool

Here you go, removal & installation of:

Front Parking/Turn Signal Lights:

• Remove the screws from the the lens and separate the lens from the bezel
• Remove the screws from the turn signal housing and pull it out
• Turn the bulb socket CCW 1/3 turn and remove it
• Installation is the reverse of this procedure

Side (Front) Marker Lights:

• Remove the screws from the marker lens
  
• Separate the lens from the headlight
• Pull the bulb from the back of the lens
• Installation is the reverse of this procedure

Hope this helps

Mike